Carbon and oxygen behavior in the RH degasser with carbon powder addition

Abstract

for ultra-low-carbon (ULC) steel production, the higher oxygen content before Ruhrstahl-Heraeus (RH) decarburization (de-C) treatment could shorten the de-C time in the RH degasser. However, this would lead to oxidation rates being exceeded by molten steel production, affecting ULC steel surface quality. In this work, a carbon powder addition (CPA) process was proposed to reduce the dissolved oxygen content at the end of RH de-C through addition of carbon powder to molten steel in the vacuum vessel. Carbon and oxygen behavior during the CPA and conventional process was then studied. The results demonstrated that the de-C rate with CPA was lower compared to the conventional process, but the carbon content at the end of de-C presented no difference. The de-C reaction for CPA process took place in the four reaction sites: (1) within the bulk steel where the spontaneous CO bubbles form; (2) splashing area on the liquid steel surface; (3) Ar bubble surface; (4) molten steel surface. The CPA process could significantly reduce the dissolved oxygen content at the end of de-C, the sum content of FeO and MnO in the slag, the aluminum consumption, and the defect rate of rolled products. This was beneficial in improving ULC steel cleanliness.

Keywords

ultra-low-carbon steel / ruhrstahl-Heraeus degasser / carbon powder / de-C / pre-deoxidization

References

[1] Takahashi M, Matsumoto H, Saito T. Mechanism of de-C in RH degasser. ISIJ Int., 1995, 35(12): 1452.

[2] Chen GJ, He SP. Circulation flow rate and de-C in the RH degasser under low atmospheric pressure. Vacuum, 2018, 153, 132.

[3] Li YH, Bao YP, Wang R, Ma LF, Liu JS. Modeling study on the flow patterns of gas-liquid flow for fast de-C during the RH process. Int. J. Miner. Metall. Mater, 2018, 25(2): 153.

[4] Guo J, Cheng SS, Guo HJ, Mei YG. Novel mechanism for the modification of Al₂O₃-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium. Int. J. Miner. Metall. Mater, 2018, 25(3): 280.

[5] Wang M, Bao YP, Yang Q, Zhao LH, Lin L. Coordinated control of carbon and oxygen for ultra-low-carbon interstitial-free steel in a smelting process. Int. J. Miner. Metall. Mater, 2015, 22(12): 1252.

[6] Geng DQ, Zheng JX, Wang K, Wang P, Liang RQ, Liu HT, Lei H, He JC. Simulation on de-C and inclusion removal process in the ruhrstahl-heraeus (RH) process with ladle bottom blowing. Metall. Mater. Trans. B, 2015, 46(3): 1484.

[7] Li YH, Bao YP, Wang R, Min M, Huang QX, Li YG. Modeling of liquid level and bubble behavior in vacuum chamber of RH process. J. Iron. Steel Res. Int., 2016, 23(4): 305.

[8] Kuwabara T, Umezawa K, Mori K, Watanabe H. Investigation of decarburization behavior in RH-reactor and its operation improvement. Trans. Iron Steel Inst. Jpn., 1988, 28(4): 305.

[9] Li BK, Fumitaka T. Modeling of circulating flow in RH degassing vessel water model designed for two-and multi-legs operations. ISIJ Int., 2000, 40(12): 1203.

[10] Chen GJ, He SP. Mixing behavior in the RH degasser with bottom gas injection. Vacuum, 2016, 130, 48.

[11] Takechi H. Metallurgical aspects on interstitial free sheet steel from industrial viewpoints. ISIJ Int., 1994, 34(1): 1.

[12] Qin YM, Wang XH, Li LP, Huang FX. Effect of oxidizing slag on cleanliness of IF steel during ladle holding process. Steel Res. Int., 2015, 86(9): 1037.

[13] Zinngrebe E, Van Hoek C, Visser H, Westendorp A, Jung IH. Inclusion population evolution in Ti-alloyed Al-killed steel during secondary steelmaking process. ISIJ Int., 2012, 52(1): 52.

[14] Zhang F, Li GQ. Control of ultra low titanium in ultra low carbon Al-Si killed steel. J. Iron Steel Res. Int., 2013, 20(4): 20.

[15] Li GH, Wang B, Liu Q, Tian XZ, Zhu R, Hu LN, Cheng GG. A process model for BOF process based on bath mixing degree. Int. J. Miner. Metall. Mater., 2010, 17(6): 715.

[16] Li PH, Bao YP, Yue F, Huang J. BOF end-point control of ultra low carbon steel. Iron Steel, 2011, 46(10): 27.

[17] Jia N, Zhang YB, Wu MW. Deoxidation practice with high-quality carbon powder to substitute part of Ferro-Aluminum in tapping of converter. Hebei Metall., 2015, 237(9): 56.

[18] Guo JL, Bao YP, Wang M. Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes. Int. J. Miner. Metall. Mater., 2017, 24(12): 1370.

[19] Kishimoto Y, Yamaguchi K, Sakuraya T, Fujii T. De-C reaction in ultra-low carbon iron melt under reduced pressure. ISIJ Int., 1993, 33(3): 791.

[20] Inoue S, Furuno Y, Usui T, Miyahara S. Acceleration of de-C in RH vacuum degassing process. ISIJ Int., 1992, 32(1): 120.

[21] Liu BS, Zhu GS, Li HX, Li BH, Cui AM. De-C rate of RH refining for ultra low carbon steel. Int. J. Miner. Metall. Mater., 2010, 17(1): 22.

[22] Liu CY, Huang FX, Wang XH. The effect of refining slag and refractory on inclusion transformation in extra low oxygen steels. Metall. Mater. Trans. B, 2016, 47(2): 999.

[23] van Ende MA, Kim YM, Cho MK, Choi J, Jung IH. A kinetic model for the Ruhrstahl Heraeus (RH) degassing process. Metall. Mater. Trans. B, 2011, 42(3): 477.

[24] Higuchi Y, Ikenaga H, Shirota Y. Effects of [C], [O] and pressure on RH vacuum de-C. Tetsu-to-Hagané, 1998, 84(10): 709.

[25] Park YG, Yi KW. A new numerical model for predicting carbon concentration during RH degassing treatment. ISIJ Int., 2007, 43(9): 1403.