Friction-stir-welded overaged 7020-T6 alloy joint: an investigation on the effect of rotational speed on the microstructure and mechanical properties

Abstract

Commercial A7020-T6 plates in the overaged state were subjected to friction stir welding with four different tool rotational speeds of 500, 710, 1000, and 1400 r/min and a single traverse feed rate of 40 mm/min. The resultant changes in the welding heat input, microstructure, and the mechanical properties of the joints were investigated. The changes were related to the processes of growth, dissolution, and re-formation of precipitates. The precipitate evolution was examined by differential scanning calorimetry, and the microstructural analysis was conducted using optical, scanning, and transmission electron microscopes. The results showed that the grain size in the stirred zone (SZ) decreased substantially compared with the base metal, but increased with tool rotational speed because of the rise in temperature. We found that the width of the heat-affected zone increased with tool rotational speed. The hardness and the tensile strength in the SZ increased with increasing heat input compared with the base metal in the overaged condition. This recovery in mechanical properties of the joints can be attributed to the dissolution and re-formation of precipitates in the SZ and the thermomechanically affected zone. This process is referred to as an “auto-aging treatment.”

Keywords

A7020-T6 / overaged / friction stir welding / precipitates / rotational speed / heat input / auto-aging

References

[1] Mishraa RS, Ma ZY. Friction stir welding and processing. Mater. Sci. Eng. R, 2005, 50(1–2): 1.

[2] Threadgill PL, Leonard AJ, Shercliff HR, Withers PJ. Friction stir welding of aluminium alloys. Int. Mater. Rev., 2009, 54(2): 49.

[3] Rathee S, Maheshwari S, Siddiquee A N. Issues and strategies in composite fabrication via friction stir processing: a review. Mater. Manuf. Processes, 2018, 33(3): 239.

[4] Ma T, den Ouden G. Softening behaviour of Al—Zn—Mg alloys due to welding. Mater. Sci. Eng. A, 1999, 266(1–2): 198.

[5] Mousavi MG, Hermans MJM, Richardson IM, den Ouden G. Grain refinement due to grain detachment in electromagnetically stirred AA7020 welds. Sci. Technol. Weld. Joining, 2003, 8(4): 309.

[6] Çam G. Friction stir welded structural materials: beyond Al-alloys. Int. Mater. Rev., 2011, 56(1): 1.

[7] Dehghani K, Ghorbani R, Soltanipoor AR. Microstructural evolution and mechanical properties during the friction stir welding of 7075-O aluminum alloy. Int. J. Adv. Manuf. Technol., 2015, 77(9–12): 1671.

[8] Çam G, Mistikoglu S. Recent developments in friction stir welding of Al-alloys. J. Mater. Eng. Perform., 2014, 23(6): 1936.

[9] Mishra RS, Ma ZY. Friction stir welding and processing. Mater. Sci. Eng. R, 2007, 50(1–2): 1.

[10] Golezani AS, Barenji RV, Heidarzadeh A, Pouraliakbar H. Elucidating of tool rotational speed in friction stir welding of 7020-T6 aluminum alloy. Int. J. Adv. Manuf. Technol., 2015, 81(5–8): 1155.

[11] Kumar K, Kailas SV, Srivatsan T. The role of tool design in influencing the mechanism for the formation of friction stir welds in aluminum alloy 7020. Mater. Manuf. Processes, 2011, 26(7): 915.

[12] Mahoney MW, Rhodes CG, Flintoff JG, Bingel WH, Spurling RA. Properties of friction-stir-welded 7075 T651 aluminum. Metall. Mater. Trans. A, 1998, 29(7): 1955.

[13] İpekoğlu G, Erim S, Çam G. Effects of temper condition and post weld heat treatment on the microstructure and mechanical properties of friction stir butt-welded AA7075 Al alloy plates. Int. J. Adv. Manuf. Technol., 2014, 70(1–4): 201.

[14] Jata KV, Sankaran KK, Ruschau JJ. Friction-stir welding effects on microstructure and fatigue of aluminum alloy 7050-T7451. Metall. Mater. Trans. A, 2000, 31(9): 2181.

[15] Su JQ, Nelson TW, Mishra R, Mahoney M. Microstructural investigation of friction stir welded 7050-T651 aluminium. Acta Mater., 2003, 51(3): 713.

[16] Gaafer AM, Mahmoud TS, Mansour EH. Microstructural and mechanical characteristics of AA7020-O Al plates joined by friction stir welding. Mater. Sci. Eng. A, 2010, 527(27): 7424.

[17] Sato YS, Urata M, Kokawa H. Parameters controlling microstructure and hardness during friction-stir welding of precipitation-hardenable aluminum alloy 6063. Metall. Mater. Trans. A, 2002, 33(3): 625.

[18] Paulisch MC, Wanderka N, Haupt M, Selve S, Driehorst I, Reimers W, Driehorst I, Reimers W. The influence of heat treatments on the microstructure and the mechanical properties in commercial 7020 alloys. Mater. Sci. Eng. A, 2015, 626, 254.

[19] Hamilton C, Dymek S, Senkov O. Characterisation of friction stir welded 7042-T6 extrusions through differential scanning calorimetry. Sci. Technol. Weld. Joining, 2012, 17(1): 42.

[20] Colegrove PA, Shercliff HR. Experimental and numerical analysis of aluminium alloy 7075-T7351 friction stir welds. Sci. Technol. Weld. Joining, 2003, 8(5): 360.

[21] Mishra RS, De PS, Kumar N. Friction Stir Welding and Processing, 2014, Switzerland, Springer International Publishing 227.

[22] Yan JH, Sutton MA, Reynolds AP. Process-structure-property relationships for nugget and heat affected zone regions of AA2524–T351 friction stir welds. Sci. Technol. Weld. Joining, 2005, 10(6): 725.

[23] Fuller CB, Mahoney MW, Calabrese M, Micona L. Evolution of microstructure and mechanical properties in naturally aged 7050 and 7075 Al friction stir welds. Mater. Sci. Eng. A, 2010, 527(9): 2233.

[24] Fonda RW, Bingert JF, Colligan KJ. Development of grain structure during friction stir welding. Scripta Mater., 2004, 51(3): 243.

[25] McNelley TR, Swaminathan S, Su JQ. Recrystallization mechanisms during friction stir welding/processing of aluminum alloys. Scripta Mater., 2008, 58(5): 349.

[26] Ma ZY, Sharma SR, Mishra RS. Effect of friction stir processing on the microstructure of cast A356 aluminum. Mater. Sci. Eng. A, 2006, 433(1–2): 269.

[27] Kumar K, Kailas SV. The role of friction stir welding tool on material flow and weld formation. Mater. Sci. Eng. A, 2008, 485(1–2): 367.

[28] Jin H, Saimoto S, Ball M, Threadgill PL. Characterisation of microstructure and texture in friction stir welded joints of 5754 and 5182 aluminium alloy sheets. Mater. Sci. Technol, 2001, 17(12): 1605.

[29] Zhang Z, Chen DL. Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites. Mater. Sci. Eng. A, 2008, 483–484, 148.