Effect of Al₂O_3sf addition on the friction and wear properties of (SiC_p+Al₂O_3sf)/Al2024 composites fabricated by pressure infiltration

Abstract

Aluminum (Al) 2024 matrix composites reinforced with alumina short fibers (Al₂O_3sf) and silicon carbide particles (SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al₂O_3sf on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al₂O_3sf, characterized by the ratio of Al₂O_3sf to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al₂O_3sf to SiC_p was increased from 0 to 1, the rate of wear mass loss (K _m) and coefficients of friction (COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K _m increased rapidly and the wear mechanism became adhesive wear.

Keywords

aluminum matrix composites / silicon carbide particles / alumina short fibers / friction properties / wear properties / infiltration

References

[1] Cui W., Xu H., Chen J.H., Ren S.B., He X.B., Qu X.H. Effect of graphite powder as a forming filler on the mechanical properties of SiCp/Al composites by pressure infiltration. Int. J. Miner. Metall. Mater., 2016, 23(5): 601.

[2] Veeresh Kumar G.B., Rao C.S.P., Selvaraj N. Studies on mechanical and dry sliding wear of Al₆0₆₁–SiC composites. Composites Part B, 2012, 43(3): 1185.

[3] Kalaichelvi V., Sivakumar D., Karthikeyan R., Palanikumar K. Prediction of the flow stress of 6061 Al–15% SiC–MMC composites using adaptive network based fuzzy inference system. Mater. Des., 2009, 30(4): 1362.

[4] Mangin C.G.E., Isaacs J.A., Clark J.P. MMCs for automotive engine applications. JOM, 1996, 48(2): 49.

[5] Torralba J.M., da Costa C.E., Velasco F. P/M aluminum matrix composites: an overview. J. Mater. Process. Technol., 2003, 133(1-2): 203.

[6] Abhik R., Umasankar V., Xavior M.A. Evaluation of properties for Al-SiC reinforced metal matrix composite for brake pads. Procedia Eng., 2014, 97, 941.

[7] Wang Y.Q., Song J.L. Dry sliding wear behavior of Al₂O₃ fiber and SiC particle reinforced aluminum based MMCs fabricated by squeeze casting method. Trans. Nonferrous Met. Soc. China, 2011, 21(7): 1441.

[8] Umasankar V., Xavior M.A., Karthikeyan S. Experimental evaluation of the influence of processing parameters on the mechanical properties of SiC^particle reinforced AA₆0₆₁ aluminium alloy matrix composite by powder processing. J. Alloys Compd., 2014, 582, 380.

[9] Geng L., Zhang H.W., Li H.Z., Guan L.N., Huang L.J. Effects of Mg content on microstructure and mechanical properties of SiC_p/AlMg composites fabricated by semi-solid stirring technique. Trans. Nonferrous Met. Soc. China, 2010, 20(10): 1851.

[10] Dong R.H., Yang W.S., Yu Z.H., Wu P., Hussain M., Jiang L.T., Wu G.H. Aging behavior of 6061Al matrix composite reinforced with high content SiC nanowires. J. Alloys Compd., 2015, 649, 1037.

[11] Lai S.W., Chung D.D.L. Fabrication of particulate aluminum-matrix composites by liquid-metal infiltration. J. Mater. Sci., 1994, 29(12): 3128.

[12] Cheng N.P., Zeng S.M., Liu Z.Y. Preparation, microstructures and deformation behavior of SiC_p/6066Al composites produced by PM route. J. Mater. Process. Technol., 2008, 202(1-3): 27.

[13] Black S. Metal-matrix composites used to lighten military brake drums. High Perform. Compos., 2010, 18(3): 101.

[14] Young J.L. Jr Kuhlmann-Wilsdorf D., Hull R. The generation of mechanically mixed layers (MMLs) during sliding contact and the effects of lubricant thereon. Wear, 2000, 246(1-2): 74.

[15] Pramila Bai B.N., Biswas S.K. Effect of magnesium addition and heat treatment on mild wear of hypoeutectic aluminium-silicon alloys. Acta Merall. Mater., 1991, 39(5): 833.

[16] Venkataraman B., Sundararajan G. Correlation between the characteristics of the mechanically mixed layer and wear behaviour of aluminum, Al-7075 alloy and Al-MMCs. Wear, 2000, 245(1-2): 22.