Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes

Abstract

During the production of Ti-bearing Al-killed ultra-low-carbon (ULC) steel, two different heating processes were used when the converter tapping temperature or the molten steel temperature in the Ruhrstahl–Heraeus (RH) process was low: heating by Al addition during the RH decarburization process and final deoxidation at the end of the RH decarburization process (process-I), and increasing the oxygen content at the end of RH decarburization, heating and final deoxidation by one-time Al addition (process-II). Temperature increases of 10°C by different processes were studied; the results showed that the two heating processes could achieve the same heating effect. The T.[O] content in the slab and the refining process was better controlled by process-I than by process-II. Statistical analysis of inclusions showed that the numbers of inclusions in the slab obtained by process-I were substantially less than those in the slab obtained by process-II. For process-I, the Al₂O₃ inclusions produced by Al added to induce heating were substantially removed at the end of decarburization. The amounts of inclusions were substantially greater for process-II than for process-I at different refining stages because of the higher dissolved oxygen concentration in process-II. Industrial test results showed that process-I was more beneficial for improving the cleanliness of molten steel.

Keywords

low carbon steel / cleanliness / RH process / heating / inclusions

References

[1] Tsunekawa H., Yamashita T., Aoyama T., Sugihara R. Mechanism of formation of streak-shaped defects on ultra-low carbon IF steel for automobile outer panels after press forming and influence of slab reheating temperature before hot rolling and Sb-addition on defects. Tetsu-to-Hagane, 2016, 102(4): 202.

[2] Palai P., Sahoo P.P., Dey A., Roy T.K., Mahashabde V.V. Constitutional segregation of Al₂O₃, in mold slag and its impact on steel cleanliness during continuous casting. Metall. Mater. Trans. B, 2013, 44(5): 1185.

[3] Jo J.O., Kim W.Y., Kim D.S., Pak J.J. Thermodynamics of titanium, nitrogen, and oxygen in liquid alloy steels. Met. Mater. Int., 2008, 14(4): 531.

[4] Qin Y.M., Wang X.H., Huang F.X., Chen B., Ji C.X. Influence of reoxidation by slag and air on inclusions in IF steel. Metall. Res. Technol., 2015

[5] Gutiérrez E., Garcia-Hernandez S., Barreto J.D.J. Mathematical analysis of the dynamic effects on the deposition of alumina inclusions inside the upper tundish nozzle. ISIJ Int., 2016, 56(8): 1394.

[6] Li P.H., Bao Y.P., Yue F., Huang J. BOF end-point control of ultra low carbon steel. Iron Steel, 2011, 46(10): 27.

[7] Basu S., Choudhary S.K., Girase N.U. Nozzle clogging behaviour of Ti-bearing Al-killed ultra low carbon steel. ISIJ Int., 2004, 44(10): 1653.

[8] Zhang F., Li G.Q. Control of ultra low titanium in ultra low carbon Al−Si killed steel. J. Iron Steel Res. Int., 2013, 20(4): 20.

[9] Qin Y.M., Wang X.H., Li L.P., Huang F.X. Effect of oxidizing slag on cleanliness of IF steel during ladle holding process. Steel Res. Int., 2015, 86(9): 1037.

[10] Liu C.Y., Huang F.X., Wang X.H. The effect of refining slag and refractory on inclusion transformation in extra low oxygen steels. Metall. Mater. Trans. B, 2016, 47(2): 999.

[11] Zinngrebe E., Hoek C.V., Visser H., Westendorp A., Jung I.H. Inclusion population evolution in Ti-alloyed Al-killed steel during secondary steelmaking process. ISIJ. Int., 2012, 52(1): 52.

[12] Wang M., Bao Y.P., Yang Q., Zhao L.H., Lu L. Coordinated control of carbon and oxygen for ultra-low-carbon interstitial-free steel in a smelting process. Int. J. Miner. Metall. Mater., 2015, 22(12): 1252.

[13] Doo W.C., Kim D.Y., Kang S.C., Yi K.W. The morphology of Al−Ti−O complex oxide inclusions formed in an ultra low-carbon steel melt during the RH process. Met. Mater. Int., 2007, 13(3): 249.

[14] Yang W., Wang X.H., Zhang L.F., Shan Q.L., Liu X.F. Cleanliness of low carbon aluminum-killed steels during secondary refining processes. Steel Res. Int., 2013, 84(5): 473.

[15] Yoon B.H., Heo K.H., Kim J.S., Sohn H.S. Improvement of steel cleanliness by controlling slag composition. Ironmaking Steelmaking, 2002, 29(3): 214.

[16] Sun M.K., Jung I.H., Lee H.G. Morphology and chemistry of oxide inclusions after Al and Ti complex deoxidation. Met. Mater. Int., 2008, 14(6): 791.