Studies on induction hardening of powder-metallurgy-processed Fe–Cr/Mo alloys

Abstract

Induction hardening of dense Fe–Cr/Mo alloys processed via the powder-metallurgy route was studied. The Fe−3Cr−0.5Mo, Fe−1.5Cr−0.2Mo, and Fe−0.85Mo pre-alloyed powders were mixed with 0.4wt%, 0.6wt%, and 0.8wt% C and compacted at 500, 600, and 700 MPa, respectively. The compacts were sintered at 1473 K for 1 h and then cooled at 6 K/min. Ferrite with pearlite was mostly observed in the sintered alloys with 0.4wt% C, whereas a carbide network was also present in the alloys with 0.8wt% C. Graphite at prior particle boundaries led to deterioration of the mechanical properties of alloys with 0.8wt% C, whereas no significant induction hardening was achieved in alloys with 0.4wt% C. Among the investigated samples, alloys with 0.6wt% C exhibited the highest strength and ductility and were found to be suitable for induction hardening. The hardening was carried out at a frequency of 2.0 kHz for 2–3 s. A case depth of 2.5 mm was achieved while maintaining the bulk (interior) hardness of approximately HV 230. A martensitic structure was observed on the outer periphery of the samples. The hardness varied from HV 600 to HV 375 from the sample surface to the interior of the case hardened region. The best combination of properties and hardening depth was achieved in case of the Fe−1.5Cr−0.2Mo alloy with 0.6wt% C.

Keywords

Fe–Cr/Mo alloys / powder metallurgy / sintered density / tensile strength / induction hardening / case depth

References

[1] German R.M. Powder Metallurgy and Particulate Materials Processing, 2005, New Jersey, USA, Metal Powder Industries Federation, Princeton 2.

[2] Salak A. Ferrous Powder Metallurgy, 1997, Cambridge, United Kingdom, Cambridge International Science Publishing 1.

[3] Sheng L.Y., Yang F., Xi T.F., Guo J.T., Ye H.Q. Microstructure evolution and mechanical properties of Ni₃Al/Al₂O₃ composite during self-propagation high-temperature synthesis and hot extrusion. Mater. Sci. Eng., A, 2012, 555, 131.

[4] Yu Y. Thermodynamic and kinetic behaviours of Astaloy CrM. PM World Congress & Exhibition, 2000

[5] Kandavel T.K., Panneerselvam T., Karthikeyan P. Optimization of deformation and densification properties of the sintered plain carbon steel. Mater. Manuf. Processes, 2015, 30(10): 1240.

[6] Sandeep. Analysis of powder metallurgy process parameters for relative density of low carbon alloy steel using design of experiments tool. Appl. Mech. Mater., 2014, 592-594, 72.

[7] Wu M.W., Tsao L.C., Chang S.Y. The influences of chromium addition and quenching treatment on the mechanical properties and fracture behaviors of diffusion-alloyed powder metal steels. Mater. Sci. Eng. A, 2013, 565, 196.

[8] Amador D.R., Torralba J.M. Study of PM alloyed steels with Ni–Cu prealloyed powders. J. Mater. Process. Technol., 2003, 143-144, 781.

[9] Engstrom U., Lindberg C., Tengzelius J. Powders and processes for high performance PM steels. Powder Metall., 1992, 35(1): 67.

[10] Unami S., Ozaki Y. Molybdenum hybrid-alloyed steel powder for high fatigue strength sintered parts using mesh-belt sintering furnace. JFE Tech. Rep., 2011, 16, 65.

[11] Kremel S., Danninger H., Yu Y. Effect of sintering conditions on particle contacts and mechanical properties of pm steels prepared from 3%Cr prealloyed powder. Powder Metall. Prog., 2002, 2(4): 211.

[12] Marcu T., Molinari A., Straffelini G., Berg S. Microstructure and tensile properties of 3%Cr-0.5%Mo high carbon PM sintered steels. Powder Metall., 2005, 48(2): 139.

[13] Hrubovcakova M., Dudrova E., Hryha E., Kabatova M., Harvanova J. Parameters controlling the oxide reduction during sintering of chromium prealloyed steel. Adv. Mater. Sci. Eng., 2013, 43, 10413.

[14] Chauhan S., Verma V., Prakash U., Tewari P.C., Khanduja D. Processing of Cr-Mo alloy steel via PM route. Mater. Today, 2016, 3(9): 2899.

[15] Hassell P.A., Ross N.V., Handbook A.S.M. Vol. 4C: Induction Heating and Heat Treatment, 1991 413.

[16] Palaniradja K., Alagumurthi N., Soundararajan V. Modeling of phase transformation in induction hardening. Open Mater. Sci. J., 2010, 4, 64.

[17] Kusmoko A., Dunne D.P., Dahar R., Li H.J. Surface treatment evaluation of induction hardened and tempered 1045 steel. Int. J. Curr. Eng. Technol., 2014, 4(3): 1236.

[18] Rudnev V. Intricacies of induction hardening powder metallurgy parts. Heat Treat. Prog., 2003 23.

[19] Ferguson H.A. ASM Handbook, Vol. 4D: Heat Treating of Irons and Steels, 1991 548.

[20] Hryha E., Nyborg L. Effectiveness of reducing agents during sintering of Cr-prealloyed PM steels. Powder Metall., 2014, 57(4): 245.

[21] Chauhan S., Verma V., Prakash U., Tewari P.C., Khanduja D. Analysis of powder metallurgy process parameters for mechanical properties of sintered Fe–Cr–Mo alloy steel. Mater. Manuf. Processeses, 2017, 32(5): 537.

[22] Maalekian M. Effect of Alloying Elements in Steel (I), 2007 10.