Effects of metal binder on the microstructure and mechanical properties of Al₂O₃-based micro-nanocomposite ceramic tool material

Abstract

The Al₂O₃−(W,Ti)C composites with Ni and Mo additions varying from 0vol% to 12vol% were prepared via hot pressing sintering under 30 MPa. The microstructure was investigated via X-ray diffraction (XRD) and scanning electron microscopy (SEM) equipped with energy dispersive spectrometry (EDS). Mechanical properties such as flexural strength, fracture toughness, and Vickers hardness were also measured. Results show that the main phases A1₂O₃ and (W,Ti)C were detected by XRD. Compound MoNi also existed in sintered nanocomposites. The fracture modes of the nanocomposites were both intergranular and transgranular fractures. The plastic deformation of metal particles and crack bridging were the main toughening mechanisms. The maximum flexural strength and fracture toughness were obtained for 9vol% and 12vol% additions of Ni and Mo, respectively. The hardness of the composites reduced gradually with increasing content of metals Ni and Mo.

Keywords

ceramic matrix nanocomposite / metal phase / microstructure / mechanical properties

References

[1] Aruna M, Dhanalakshmi V, Mohan S. Wear analysis of ceramic cutting tools in finish turning of Inconel 718. Int. J. Eng. Sci. Technol., 2010, 2(9): 4253.

[2] Sharifitabar M, Khaki JV, Sabzevar MH. Fabrication of Fe-TiC-Al₂O₃ composites on the surface of steel using a TiO₂-Al-C-Fe combustion reaction induced by gas tungsten arc cladding. Int. J. Miner. Metall. Mater., 2016, 23(2): 193.

[3] Yan ZQ, Chen F, Ye FX, Zhang DP, Cai YX. Microstructures and properties of Al₂O₃ dispersion-strengthened copper alloys prepared through different methods. Int. J. Miner. Metall. Mater., 2016, 23(12): 1437.

[4] Gille G, Bredthauer J, Griesa B, Mendea B, Heinrich W. Advanced and new grades of WC and binder powder–their properties and application. Int. J. Refract. Met. Hard Mater., 2000, 18(2-3): 87.

[5] Lieberthal M, Kaplan WD. Processing and properties of Al₂O₃ nanocomposites reinforced with sub-micron Ni and NiAl₂O₄. Mater. Sci. Eng. A, 2001, 302(1): 83.

[6] Kafkaslioglu B, Tür YK. Pressureless sintering of Al₂O₃/Ni nanocomposites produced by heterogeneous precipitation method with varying nickel contents. Int. J. Refract. Met. Hard Mater., 2016, 57, 139.

[7] Aharon O, Bar-Ziv S, Gorni D, Cohen-Hyamsa T, Kaplan WD. Residual stresses and magnetic properties of alumina–nickel nanocomposites. Scripta Mater., 2004, 50(9): 1209.

[8] Yao XM, Huang ZR, Chen LD, Jiang DL, Tan SH, Michel D, Wang G, Mazerolles L, Pastol JL. Alumina–nickel composites densified by spark plasma sintering. Mater. Lett., 2005, 59(18): 2314.

[9] Gluzer G, Kaplan WD. Particle occlusion and mechanical properties of Ni–Al₂O₃ nanocomposites. J. Eur. Ceram. Soc., 2013, 33(15-16): 3101.

[10] Lu JS, Gao L, Guo JK, Niihara K. Preparation, sintering behavior, and microstructural studies of Al₂O₃/Mo composites from boehmite-coated Mo powders. Mater. Res. Bull., 2000, 35(14-15): 2387.

[11] Diáz LA, Valdés AF, Diáz C, Espino AM, Torrecillas R. Alumina/molybdenum nanocomposites obtained in organic media. J. Eur. Ceram. Soc., 2003, 23(15): 2829.

[12] Li GJ, Huang XX, Guo JK. Microstructure and mechanical properties of Al₂O₃/Ni cermet. J. Inorg. Mater., 2004, 19(3): 546.

[13] Shi XL, Yang H, Shao GQ, Duan XL, Xiong Z. Microwave sintering of Al₂O₃/WC-10Co/ZrO₂/Ni cermets. J. Cent. South. Univ. Sci. Technol., 2007, 38(4): 623.

[14] Wang TC, Chen RZ, Tuan WH. Effect of zirconia addition on the oxidation resistance of Ni-toughened Al₂O₃. J. Eur. Ceram. Soc., 2004, 24(5): 833.

[15] Rodriguez-Suarez T, Bartolomé JF, Smirnov A, Lopez- Esteban S, Díaz LA, Torrecillas R, Moya JS. Electroconductive Alumina–TiC–Ni nanocomposites obtained by Spark Plasma Sintering. Ceram. Int., 2011, 37(5): 1631.

[16] Ji LY, Ma WM, Li XK, Ma L, Liu J, Wu Y. Preparation and mechanical properties of Al₂O₃-TiCN/Co-Ni composite ceramics. J. Chin. Ceram. Soc., 2015, 43(7): 980.

[17] Zhao GL, Huang CZ, He N, Liu HL, Zou B. Microstructural development and mechanical properties of reactive hot pressed nickel-aided TiB2-SiC ceramics. Int. J. Refract. Met. Hard Mater., 2016, 61, 13.

[18] Kwon H, Kang S. Microstructure and mechanical properties of TiC–WC–(Ti,W)C–Ni cermets. Mater. Sci. Eng. A, 2009, 520(1-2): 75.

[19] Zhao J, Ai X, Deng JX, Wang JH. Thermal shock behaviors of functionally graded ceramic tool materials. J. Eur. Ceram. Soc., 2004, 24(5): 847.

[20] Zhou YH, Ai X, Zhao J, Yuan XL, Xue Q. Mechanical properties and microstructure of Al₂O₃/(W,Ti)C nanocomposite. Key Eng. Mater., 2008, 368, 717.

[21] Evans AG, Charles EA. Fracture toughness determinations by indentation. J. Am. Ceram. Soc., 1976, 59(7-8): 371.

[22] Ibrahim IA, Mohamed FA, Lavemia EJ. Particulate reinforced metal matrix composites—a review. J. Mater. Sci., 1991, 26(5): 1137.

[23] Konopka K. Alumina composites with metal particles in ceramic matrix. Powder Metall. Met. Ceram., 2015, 54(5): 374.

[24] Evans AG, Faber KT. Toughening of ceramics by circumferential microcracking. J. Am. Ceram. Soc., 1981, 64(7): 394.

[25] Awaji H, Choi SM, Yagi E. Mechanisms of toughening and strengthening in ceramic-based nanocomposites. Mech. Mater., 2002, 34(7): 411.