Effect of magnesium on the aluminothermic reduction rate of zinc oxide obtained from spent alkaline battery anodes for the preparation of Al–Zn–Mg alloys

Abstract

The aluminothermic reduction of zinc oxide (ZnO) from alkaline battery anodes using molten Al may be a good option for the elaboration of secondary 7000-series alloys. This process is affected by the initial content of Mg within molten Al, which decreases the surface tension of the molten metal and conversely increases the wettability of ZnO particles. The effect of initial Mg concentration on the aluminothermic reduction rate of ZnO was analyzed at the following values: 0.90wt%, 1.20wt%, 4.00t%, 4.25wt%, and 4.40wt%. The ZnO particles were incorporated by mechanical agitation using a graphite paddle inside a bath of molten Al maintained at a constant temperature of 1123 K and at a constant agitation speed of 250 r/min, the treatment time was 240 min and the ZnO particle size was 450-500 mesh. The results show an increase in Zn concentration in the prepared alloys up to 5.43wt% for the highest initial concentration of Mg. The reaction products obtained were characterized by scanning electron microscopy and X-ray diffraction, and the efficiency of the reaction was measured on the basis of the different concentrations of Mg studied.

Keywords

aluminothermic reduction / alkaline batteries / zinc oxide / waste utilization / aluminum zinc magnesium alloys

References

[1] Sobianowska-Turek A., Szczepaniak W., Zablocka-Malicka M. Electrochemical evaluation of manganese reducers: recovery of Mn from Zn-Mn and Zn-C battery waste. J. Power Sources, 2014, 270, 668.

[2] Pereira Mantuano D., Dorella G., Cristina Alves Elias R., Borgues Mansur M. Analysis of a hydrometallurgical route to recover base metals from spent rechargeable batteries by liquid-liquid extraction with Cyanex 272. J. Power Sources, 2006, 159(2): 1510.

[3] Guevara-García J.A., Montiel-Corona V. Used battery collection in central Mexico: metal content. legislative/management situation and statistical analysis, J. Environ. Manage., 2012, 95, S154.

[4] Langlais J., Harris R. Strontium extraction by aluminothermic reduction. Can. Metall. Q., 1992, 31, 127.

[5] Muñiz R., Flores A., Torres J., Luna S., Rodríguez N. A kinetic study of the strontium extraction by metallothermic reduction using submerged SrO powders injection. Mater. Lett., 2008, 62(4-5): 637.

[6] Luna J.S., Flores A. A., Muñiz V. R., Fuentes V. A.F., Torres J., Rodríguez N., Ortiz R. J.C., Orozco P. Cerium extraction by metallothermic reduction using cerium oxide powder injection. J. Rare Earths, 2011, 29(1): 74.

[7] Flores A., Juarez R., Torres J., Ayala Z. A kinetic study on the aluminotjermic reduction of ZrO₂. J. Eng. Technol., 2011, 2(1): 17.

[8] Udhayabanu V., Singh N., Murty B.S. Mechanical activation of aluminothermic reduction of NiO by high energy ball milling. J. Alloys Compd., 2010, 497(1-2): 142.

[9] A. Flores Valdés, J. Torres, and R. Ochoa Palacios, Elaboration of Al-Mn alloys by aluminothermic reduction of Mn₂O₃, [in] Z. Ahmad, Aluminium Alloys: New Trends in Fabrication and Applications, Intech Open Science, Rijeka, 2012, p. 301.

[10] Barrett H.A., Borkiewicz O., Krekeler P.S. An investigation of zincite from spent anodic portions of alkaline batteries: An industrial mineral approach for evaluating stock material for recycling potential. J. Power Sources, 2011, 196(1): 508.

[11] Afshar S., Allaire C. Furnaces: improving low cement castables by non-wetting additives. JOM, 2001, 53(8): 24.

[12] Shen P., Fujii H., Matsumoto T., Nogi K. The influence of surface structure on wetting of α-Al₂O₃ by aluminum in a reduce atmosphere. Acta Mater., 2003, 51(16): 4897.

[13] Sangghaleh A., Halali M. Effect of magnesium addition on the wetting of alumina by aluminium. Appl. Surf. Sci., 2009, 255(19): 8202.

[14] Zulfia A., Hand R.J. The production of Al-Mg alloy/SiC metal matrix composites by pressureless infiltration. J. Mater. Sci., 2002, 37(5): 955.

[15] Ricci E., Novakovic R. Wetting and surface tension measurements on gold alloys. Gold Bull., 2001, 34(2): 41.

[16] Asavavisithcahi S., Kennedy A.R. The effect of Mg addition on the stability of Al-Al₂O₃ foams made by a powder metallurgy route. Scripta Mater., 2006, 54(7): 1331.

[17] Fujji H., Nakae H. Equilibrium contact angle in the magnesium oxide/aluminium system. Acta Mater., 1996, 44(9): 3567.

[18] Flores A., Torres J. Kvackaj T., Bidulsky R. New approaches to reaction kinetics during molten aluminum refining using electron backscatter diffraction (EBSD). Aluminium Alloys Theory and Applications, 2011, Rijeka, Intech Open Access Publisher, 285.