Microstructure simulation of rapidly solidified ASP30 high-speed steel particles by gas atomization

Abstract

In this study, the microstructure evolution of rapidly solidified ASP30 high-speed steel particles was predicted using a simulation method based on the cellular automaton-finite element (CAFE) model. The dendritic growth kinetics, in view of the characteristics of ASP30 steel, were calculated and combined with macro heat transfer calculations by user-defined functions (UDFs) to simulate the microstructure of gas-atomized particles. The relationship among particle diameter, undercooling, and the convection heat transfer coefficient was also investigated to provide cooling conditions for simulations. The simulated results indicated that a columnar grain microstructure was observed in small particles, whereas an equiaxed microstructure was observed in large particles. In addition, the morphologies and microstructures of gas-atomized ASP30 steel particles were also investigated experimentally using scanning electron microscopy (SEM). The experimental results showed that four major types of microstructures were formed: dendritic, equiaxed, mixed, and multi-droplet microstructures. The simulated results and the available experimental data are in good agreement.

Keywords

high-speed steel / rapid solidification / microstructure / grain growth / gas atomization

References

[1] García-Escorial A., Lieblich M. Microstructural characterisation of Ni₇₅Al₂₅ and Ni_31.5Al_68.5 powder particles produced by gas atomisation. J. Alloys Compd., 2014, 586(S1): S489.

[2] Yang M., Song C.J., Dai Y.X., Zhu L., Li K.F., Zhai Q.J. Microstructural evolution of gas atomized Fe₂₅Cr_3.2C alloy powders. J. Iron Steel Res. Int., 2011, 18(2): 75.

[3] Song C.J., Guo Y.Y., Zhu L., Li K.F., Yang M., Zhai Q.J. Structure evolution of the atomized powders of Fe-25Cr-3.9C alloy with addition of ni and b elements. Adv. Mater. Res., 2011, 239-242, 44.

[4] Behúlová M., Mesárošová J., Grgac P. Analysis of the influence of the gas velocity, particle size and nucleation temperature on the thermal history and microstructure development in the tool steel during atomization. J. Alloys Compd., 2014, 615, S217.

[5] Rokni M.R., Widener C.A., Crawford G.A. Microstructural evolution of 7075 Al gas atomized powder and high-pressure cold sprayed deposition. Surf. Coat. Technol., 2014, 251, 254.

[6] Song C.J., Li K.F., Xie K., Lu W., Zhao S.C., Han Q.Y., Zhai Q.J. The effect of the nucleation ability on solidified microstructures of gas-atomized Fe-6.5 wt.%Si alloy powder. Powder Technol., 2014, 263, 31.

[7] Tourret D., Reinhart G., Gandin C.A., Iles G.N., Dahlborg U., Calvo-Dahlborg M., Bao C.M. Gas atomization of Al-Ni powders: solidification modeling and neutron diffraction analysis. Acta Mater., 2011, 59(17): 6658.

[8] Kusý M., Behulova M., Grgac P. Influence of the thermal history of a particle during atomization on the morphology of carbides in a hypereutectic iron based alloy. J. Alloys Compd., 2012, 536, S541.

[9] Xu Q., Lavernia E.J. Influence of nucleation and growth phenomena on microstructural evolution during droplet-based deposition. Acta Mater., 2001, 49(18): 3849.

[10] Norman A.F., Eckler K., Zambon A., Gärtner F., Moir S.A., Ramous E., Herlach D.M., Greer A.L. Application of microstructure- selection maps to droplet solidification: a case study of the Ni–Cu system. Acta Mater., 1998, 46(10): 3355.

[11] Fedrizzi A., Pellizzari M., Zadra M. Influence of particle size ratio on densification behaviour of AISI H13/AISI M3:2 powder mixture. Powder Technol., 2012, 228, 435.

[12] Gandin C.A., Rappaz M. A coupled finite element-cellular automaton model for the prediction of dendritic grain structures in solidification processes. Acta Metall. Mater., 1994, 42(7): 2233.

[13] Rappaz M., Gandin C.A. Probabilistic modelling of microstructure formation in solidification processes. Acta Metall. Mater., 1993, 41(2): 345.

[14] Kurz W., Giovanola B., Trivedi R. Theory of microstructural development during rapid solidification. Acta Mater., 1986, 34(5): 823.

[15] W. Boettinger, S. Coriell, and R. Trivedi, Rapid Solidification Processing: Principles and Technologies IV, Edited by R. Mehrabian and P. Parrish, Claitor’s Pub, Baton Rouge, LA, 1988, p. 13.

[16] Liu X.R., Cao C.D., Wei B. Microstructure evolution and solidification kinetics of undercooled Co–Ge eutectic alloys. Scripta Mater., 2002, 46(1): 13.

[17] Galenko P.K., Krivilyov M.D. Modeling of a transition to diffusionless dendritic growth in rapid solidification of a binary alloy. Comput. Mater. Sci., 2009, 45(4): 972.

[18] A.M. Mullis, Prediction of the operating point of dendrites growing under coupled thermosolutal control at high growth velocity, Phys. Rev. E, 83(2011), art. No. 061601.

[19] Liu N., Liu F., Yang G.C., Chen Y.Z., Yang C.L., Li J.S., Zhou Y.H. Dendrite growth in undercooled Fe–Co melt. J. Alloys Compd., 2008, 455(1-2): L6.

[20] Panofen C., Herlach D.M. Solidification of highly undercooled Si and Si–Ge melts. Mater. Sci. Eng. A, 2007, 449–451, 699.

[21] Ruan Y., Dai F.P. Rapid dendrite growth subjected to multi-solute trapping in an undercooled Fe-based quaternary alloy. Intermetallics, 2012, 25, 80.

[22] Thévoz P.h., Desbiolles J.L., Rappaz M. Modeling of equiaxed microstructure formation in casting. Metall. Trans. A, 1989, 20(2): 311.

[23] Lee E.S., Ahn S. Solidification progress and heat transfer analysis of gas-atomized alloy droplets during spray forming. Acta Mater., 1994, 42(9): 3231.

[24] Guan W.B., Gao Y.L., Zhai Q.J., Xu K.D. Effect of droplet size on nucleation undercooling of molten metals. J. Mater. Sci., 2004, 39(14): 4633.

[25] Mathur P., Apelian D., Lawley A. Analysis of the spray deposition process. Acta Mater., 1989, 37(2): 429.

[26] Levi C.G., Mehrabian R. Heat flow during rapid solidification of undercooled metal droplets. Metall. Trans. A, 1982, 13(2): 221.

[27] Behulova M., Moravcik R., Kusy M., Caplovic L., Grgac P., Stancek L. Influence of atomisation on solidification microstructures in the rapidly solidified powder of the Cr–Mo–V tool steel. Mater. Sci. Eng. A, 2001, 304(1): 540.

[28] Trivedi R., Jin F., Anderson I.E. Dynamical evolution of microstructure in finely atomized droplets of Al-Si alloys. Acta Mater., 2003, 51(2): 289.

[29] Wisutmethangoon S., Plookphol T., Sungkhaphaitoon P. Production of SAC305 powder by ultrasonic atomization. Powder Technol., 2011, 209(1-3): 105.

[30] Cochrane R.F., Evans P.V., Greer A.L. Competitive growth analysis of phase formation in Al-8wt.% Fe. Mater. Sci. Eng. A, 1991, 133, 803.

[31] Zambon A., Badan B., Vedovato G., Ramous E. Morphologies in gas-atomized Fe₅₀Ni₃₀Si₁₀B₁₀ amorphizable alloy powders. Mater. Sci. Eng. A, 2001, 304-306, 452.