Size distribution of inclusions in 12%Cr stainless steel with a wide range of solidification cooling rates

Abstract

The effect of solidification cooling rate on the size and distribution of inclusions in 12%Cr stainless steel was investigated. A wide range of solidification cooling rates (from 0.05 to 10⁶ K·s^-1) was achieved using various solidification processes, including conventional casting, laser remelting, and melt spinning. The size and distribution of inclusions in the steel were observed and statistically collected. For comparison, mathematical models were used to calculate the sizes of inclusions at different solidification cooling rates. Both the statistical size determined from observations and that predicted from calculations tended to decrease with increasing cooling rate; however, the experimental and calculated results did not agree well with each other at excessively high or low cooling rate. The reasons for this discrepancy were theoretically analyzed. For the size distribution of inclusions, the effect of cooling rate on the number densities of large-sized (> 2 μm) inclusions and small-sized (≤ 2 μm) inclusions were distinct. The number density of inclusions larger than 1 µm was not affected when the cooing rate was less than or equal to 6 K·s^-1 because inclusion precipitation was suppressed by the increased cooling rate.

Keywords

solidification / cooling rate / inclusions / size distribution / number density / stainless steels

References

[1] Shim J.H., Oh Y.J., Suh J.Y., Cho Y.W., Shim J.D., Byun J.S., Lee D.N. Ferrite nucleation potency of non-metallic inclusions in medium carbon steels. Acta Mater., 2001, 49(12): 2115.

[2] Byun J.S., Shim J.H., Cho Y.W., Lee D.N. Non-metallic inclusion and intragranular nucleation of ferrite in Ti-killed C-Mn steel. Acta Mater., 2003, 51(6): 1593.

[3] Jung I.H., Decterov S.A., Pelton A.D. Computer applications of thermodynamic databases to inclusion engineering. ISIJ Int., 2004, 44(3): 527.

[4] Zhang L.F., Thomas B.G. State of the art in the control of inclusions during steel ingot casting. Metall. Mater. Trans. B, 2006, 37(5): 733.

[5] Goto H., Miyazawa K.I., Yamaguchi K.I., Ogibayashi S., Tanaka K. Effect of cooling rate on oxide precipitation during solidification of low carbon steels. ISIJ Int., 1994, 34(5): 414.

[6] Goto H., Miyazawa K.I., Yamada W., Tanaka K. Effect of cooling rate on composition of oxides precipitated during solidification of steels. ISIJ Int., 1995, 35(6): 708.

[7] Goto H., Miyazawa K.I., Honma H. Effect of the primary oxide on the behavior of the oxide precipitating during solidification of steel. ISIJ Int., 1996, 36(5): 537.

[8] Ma Z.T., Janke D. Characteristics of oxide precipitation and growth during solidification of deoxidized steel. ISIJ Int., 1998, 38(1): 46.

[9] Kikuchi N., Nabeshima S., Kishimoto Y., Sridhar S. Micro-structure refinement in low carbon high manganese steels through Ti-deoxidation: inclusion precipitation and solidification structure. ISIJ Int., 2008, 48(7): 934.

[10] Kikuchi N., Nabeshima S., Yamashita T., Kishimoto Y., Sridhar S., Nagasaka T. Micro-structure refinement in low carbon high manganese steels through Ti-deoxidation, characterization and effect of secondary deoxidation particles. ISIJ Int., 2011, 51(12): 2019.

[11] Huang F.X., Zhang J.M., Wang X.H., Fang Y., Yu Y. Nonmetallic inclusions in SUS304 strip produced by twin-roll strip casting. J. Univ. Sci. Technol. Beijing, 2008, 15(2): 110.

[12] Pryds N.H., Johnson E., Linderoth S., Pedersen A.S. Microstructural investigation of a rapidly solidified 12Cr-Mo-V steel. Metall. Mater. Trans. A, 1998, 29(1): 367.

[13] Liu Z.Z., Wei J., Cai K.K. A coupled mathematical model of microsegregation and inclusion precipitation during solidification of silicon steel. ISIJ Int., 2002, 42(9): 958.

[14] Wang M.L., Cheng G.G., Zhao P., Qiu S.T., Gan Y. Formation thermodynamics of titanium oxide during solidification of low carbon steel containing titanium. J. Iron Steel Res., 2004, 16(3): 40.

[15] Park J.H., Lee S.B., Gaye H.R. Thermodynamics of the formation of MgO-Al₂O₃-TiOX inclusions in Ti-stabilized 11Cr ferritic stainless steel. Metall. Mater. Trans. B, 2008, 39(6): 853.

[16] Ohnaka I. Mathematical analysis of solute redistribution during solidification with diffusion in solid phase. Trans. ISIJ, 1986, 26(12): 1045.

[17] Choudhary S.K., Ghosh A. Mathematical model for prediction of composition of inclusions formed during solidification of liquid steel. ISIJ Int., 2009, 49(12): 1819.

[18] Li Z.Q., Yu J.K., Yuan L. Coupled model for growth of dendrites and inclusions during solidification process of molten steel. Mater. Res. Innov., 2013, 17(2): 60.

[19] Suzuki M., Yamaguchi R., Murakami K., Nakada M. Inclusion particle growth during solidification of stainless steel. ISIJ Int., 2001, 41(3): 247.

[20] Wang Y.N., Bao Y.P., Wang M., Zhang L.C. Precipitation behavior of BN type inclusions in 42CrMo steel. Int. J. Miner. Metall. Mater., 2013, 20(1): 28.

[21] Yang W., Duan H.J., Zhang L.F., Ren Y. Nucleation, growth, and aggregation of alumina inclusions in steel. JOM, 2013, 65(9): 1173.

[22] Zhang L.F. Nucleation, growth, transport, and entrapment of inclusions during steel casting, 2013, 65(9): 1138.