Surface properties of superfine alumina trihydrate after surface modification with stearic acid

Abstract

The surface properties of superfine alumina trihydrate (ATH) after surface modification were studied by measuring the contact angle, active ratio, oil adsorption, total organic carbon, adsorption ratio, and Fourier transform infrared (FTIR) spectrum. The contact angle increased initially and then slowly decreased with an increase of the amount of stearic acid. However, the surface free energy decreased initially and then increased. Surface modification with stearic acid or sodium stearate can benefit from elevating temperature. The base surface tension component and the free energy of Lewis acid-base both declined sharply following the surface modification. Excess stearic acid was physically adsorbed in the form of multilayer adsorption, and an interaction between oxygen on the ATH surface and hydroxyl in stearic acid was subsequently determined. Our results further indicated that the contact angle and adsorption ratio can be used as control indicators for surface modification compared with active ratio, oil adsorption and total organic carbon.

Keywords

alumina trihydrate / surface modification / stearic acid / surface free energy / surface tension / contact angle

References

[1] Kind D.J., Hull T.R. A review of candidate fire retardants for polyisoprene. Polym. Degrad. Stab., 2012, 97(3): 201.

[2] Cárdenas M.A., García-López D., Gobernado-Mitre I., Merino J.C., Pastor J.M., Martínez J. d.e._D., Barbeta J., Calveras D. Mechanical and fire retardant properties of EVA/clay/ATH nanocomposites: effect of particle size and surface treatment of ATH filler. Polym. Degrad. Stab., 2008, 93(11): 2032.

[3] Wang Z.Y., Guo F., Chen J.F. Surface modification of nano-aluminium trihydrate (ATH) and its flame-retardant application with ethylene-vinyl acetate (EVA). J. Beijing Univ. Chem. Technol., 2006, 33(4): 9.

[4] Zhou X.Y., Li C.L., Huo D.W., Li J., Wu S.Y. Thermal stability and oil absorption of aluminum hydroxide treated by dry modification with different modifiers. Trans. Nonferrous Metal. Soc. China, 2008, 18(4): 908.

[5] Cui W.G., Gao Y.L., Wei Q., Mu W. Influence of the surface modification of a filler on the properties of high-impact polystyrene composites. J. Appl. Polym. Sci., 2009, 112(1): 359.

[6] Zhao S., Ma Q., Yu B., Li H. Surface modification and evaluation of ultrafine Al(OH)₃ powder. J. Shenyang Jianzhu Univ. Nat. Sci., 2008, 24(6): 1025.

[7] Hu W.X., Zhang Z.Q. Study on preparation and modification of nanosized aluminium hydroxide. J. Wuhan Inst. Technol., 2007, 29(2): 31.

[8] Liu S.J., Zhang W.G., Lei S.L. Study on in situ combined chemical modification on surfaces of aluminum hydroxide powder. China Plast., 2005, 19(4): 49.

[9] Liu L.J., Guo F., Chen J.F. Surface modification of nanosized aluminium trihydrate. J. Beijing Univ. Chem. Technol., 2004, 31(3): 22.

[10] Qin Y.N., Wu B.L., Ni Y. Surface modification and thermal decomposition action of aluminum hydroxide. J. Guilin Univ. Technol., 2007, 27(1): 118.

[11] Zhang X.G., Guo F., Chen J.F., Wang G.Q., Liu H. Investigation of interfacial modification for flame retardant ethylene vinyl acetate copolymer/alumina trihydrate nanocomposites. Polym. Degrad. Stab., 2005, 87(3): 411.

[12] Trawczynski J.T. Effect of aluminum hydroxide precipitation conditions on the alumina surface acidity. Ind. Eng. Chem. Res., 1996, 35(1): 241.

[13] Fukushi K., Tsukimura K., Yamada H. Surface acidity of amorphous aluminum hydroxide. Acta Geol. Sin., 2006, 80(2): 206.

[14] Vidruk R., Landau M.V., Herskowitz M., Ezersky V., Goldbourt A. Control of surface acidity and catalytic activity of γ-Al₂O₃ by adjusting the nanocrystalline contact interface. J. Catal., 2011, 282(1): 215.

[15] Owens D.K., Wendt R.C. Estimation of the surface free energy of polymers. J. Appl. Polym. Sci., 1969, 13(8): 1741.

[16] YS/T 618–2007 Test Methods for Oil Adsorption of Aluminium Hydroxide for Filler, National Development and Reform Commission of China, 2007

[17] GB 17378.5–1998, The Specification for Marine Monitoring: Part 5. Sediment Analysis, Standardization Administration of China, 1998

[18] van Oss C.J., Chaudhury M.K., Good R.J. The mechanism of partition in aqueous media. Sep. Sci. Technol., 1987, 22(6): 1515.

[19] van Oss C.J., Good R.J., Busscher R.J. Estimation of the polar surface tension parameters of glycerol and formamide, for use in contact angle measurements on polar solids. J. Dispersion Sci. Technol., 1990, 11(1): 75.

[20] Wang H., Gu G.H., Qiu G.Z. Evaluation of surface free energy of polymers by contact angle goniometry. J. Cent. South Univ. Sci. Technol., 2006, 37(5): 942.

[21] Yang Y.C., Jeong S.B., Yang S.Y., Chae Y.B., Kim H.S. The changes in surface properties of the calcite powder with stearic acid treatment. Mater. Trans., 2009, 50(3): 695.

[22] Gan Y., Franks G.V. Charging behavior of the gibbsite basal (001) surface in NaCl solution investigated by AFM colloidal probe technique. Langmuir, 2006, 22(14): 6087.

[23] Wang H., Gu G.H. Surface free energy of solid matter and its hydrophilic/hydrophobic nature. Chemistry, 2009, 12, 1091.

[24] Kwok D.Y., Li D., Neumann A.W. Evaluation of the Lifshitz–van der Waals/acid-base approach to determine interfacial tensions. Langmuir, 1994, 10(4): 1323.