Microstructural evolution of a heat-treated H23 tool steel

Abstract

The microstructure and the stability of carbides after heat treatments in an H23 tool steel were investigated. The heat treatments consisted of austenization at two different austenizing temperatures (1100°C and 1250°C), followed by water quenching and double-aging at 650°C, 750°C, and 800°C with air cooling between the first and second aging treatments. Martensite did not form in the as-quenched microstructures, which consisted of a ferrite matrix, M₆C, M₇C₃, and MC carbides. The double-aged microstructures consisted of a ferrite matrix and MC, M₆C, M₇C₃, and M₂₃C₆ carbides. Secondary hardening as a consequence of secondary precipitation of fine M₂C carbides did not occur. There was disagreement between the experimental microstructure and the results of thermodynamic calculations. The highest double-aged hardness of the H23 tool steel was 448 HV after austenization at 1250°C and double-aging at 650°C, which suggested that this tool steel should be used at temperatures below 650°C.

Keywords

tool steel / microstructural evolution / heat treatment / carbides / stability / hardness

References

[1] Roberts GA, Kraus G, Kennedy RL. Tool Steels, 1998, Ohio, Materials Park, ASM International

[2] IOP Conf. Ser. Mater. Sci. Eng., 2012, 28(1art.012024)

[3] Bała P, Krawczyk J. Transformation during quenching and ageing of hot-work tool steel. Hradec Moravici, 2009, 19, 1.

[4] Zhang Z, Delagnes D, Bernhart G. Microstructure evolution of hot-work tool steels during tempering and definition of a kinetic law based on hardness measurements. Mater. Sci. Eng. A, 2004, 380, 222.

[5] Medvedeva A, Bergström J, Gunnarsson S, Andersson J. High temperature properties and microstructural stability of hot work tool steels. Mater. Sci. Eng. A, 2009, 523(1–2): 39.

[6] Nurbanasari M, Tsakiropoulos P, Palmiere EJ. A study of carbide precipitation in a H21 tool steel. ISIJ Int., 2014, 54(7): 1667.

[7] Thomson RC, Bhadeshia HKDH. Carbide precipitation in 12Cr1MoV power plant steel. Metall. Trans. A, 1992, 23, 1171.

[8] Dudova N, Kaibyshev R. On the precipitation sequence in a 10% Cr steel under tempering. ISIJ Int., 2011, 51(5): 826.

[9] Asadabad MA, Kheirandish S, Novinrooz AJ. Tempering behavior of 4.5Cr-2W-0.25V steel. J. Iron Steel Res. Int., 2010, 17(10): 57.

[10] Nurbanasari M, Tsakiropoulos P, Palmiere EJ. On the solidification of a H23 tool steel. Trans. Indian Inst. Met., 2014, 67(6): 935.

[11] Mebarki N, Delagnes D, Lamesle P, Delmas F, Levaillant C. Relationship between microstructure and mechanical properties of a 5% Cr tempered martensitic tool steel. Mater. Sci. Eng. A, 2004, 387–389, 171.

[12] Elrakayby AM, Mills B. Identification of carbides in high-speed steels. J. Mater. Sci. Lett., 1986, 5, 332.

[13] Abe F, Araki H, Noda T. The effect of tungsten on dislocation recovery and precipitation behavior of low-activation martensitic 9Cr steels. Metall. Trans. A, 1991, 22, 2225.

[14] Pickering FB. Krauss G, Nordberg H. The properties of tool steels for mould and die applications. Tool Materials for Molds and Dies: Application and Performance, 1987, Colorado, CSM Press Golden, 3.

[15] Dyson DJ, Andrews KW. Carbide M₇C₃ and its formation in alloy steels. J. Iron Steel Inst., 1969, 207(2): 208.

[16] Kuo K. Carbides in chromium, molybdenum, and tungsten steels. J. Iron Steel Inst., 1953, 173, 363.

[17] Wilson R. Metallurgy and Heat Treatment of Tool Steel, 1975, London, Mc Graw-Hill

[18] Totten GE, Xie L, Funatani K. Handbook of Mechanical Alloy Design, 2004, New York, Marcel Dekker Inc

[19] Karagoz S, Fischmeister H. Microstructure and toughness in high speed tool steels: the influence of hot reduction and austenitization temperature. Steel Res., 1987, 58(8): 353.

[20] Podder A S, Bhadeshia HKDH. Thermal stability of austenite retained in bainitic steels. Mater. Sci. Eng. A, 2010, 527(7–8): 2121.

[21] Cai GJ, Andren HO, Svensson LE. Microstructural change of a 5% Cr steel weld metal during tempering. Mater. Sci. Eng. A, 1998, 242(1–2): 202.

[22] Baker RG, Nutting J. The tempering of 2.25Cr%-1%Mo steel after quenching and normalizing. J. Iron Steel Inst., 1959, 202, 257.

[23] Bhadeshia HKDH, Honeycombe RWK. Steels: Microstructure and Properties, 2006, Oxford, Elsevier Ltd.

[24] Bjärbo A, Hättestrand M. Complex carbide growth, dissolution and coarsening in a modified 12 pct chromium steel-an experimental and theoretical study. Metall. Mater. Trans. A, 2001, 32(1): 19.

[25] Asakura K, Kohyama A, Yamada T. Mechanical properties and microstructure changes of low-activation 3Cr-2W-V-Ti ferritic steels developed for nuclear applications. ISIJ Int., 1990, 30(11): 947.