Acoustic emission study of the plastic deformation of quenched and partitioned 35CrMnSiA steel

Abstract

Acoustic emission (AE) monitored tensile tests were performed on 35CrMnSiA steel subjected to different heat treatments. The results showed that quenching and partitioning (Q-P) heat treatments enhanced the combined mechanical properties of high strength and high ductility for commercial 35CrMnSiA steel, as compared with traditional heat treatments such as quenching and tempering (Q-T) and austempering (AT). AE signals with high amplitude and high energy were produced during the tensile deformation of 35CrMnSiA steel with retained austenite (RA) in the microstructure (obtained via Q-P and AT heat treatments) due to an austenite-to-martensite phase transformation. Moreover, additional AE signals would not appear again and the mechanical properties would degenerate to a lower level once RA degenerated by tempering for the Q-P treated steel.

Keywords

low alloy steels / plastic deformation / heat treatment / acoustic emissions / martensitic transformations

References

[1] Matlock DK, Speer JG. Third Generation of AHSS: Microstructure Design Concepts, 2009, London, Springer, 185.

[2] Edmonds DV, Speer JG. Martensitic steels with carbide free microstructures containing retained austenite. Mater. Sci. Technol., 2010, 26(4): 386.

[3] Hong SC, Ahn JC, Nam SY, Kim SJ, Yang HC, Speer JG, Matlock DK. Mechanical properties of high-Si plate steel produced by the quenching and partitioning process. Met. Mater. Int., 2007, 13(6): 439.

[4] Edmonds D, Matlock D, Speer J. Developments in High Strength Steels with Duplex Microstructures of Bainite or Martensite with Retained Austenite: Progress with Quenching and Partitioning Heat Treatment, 2011, London, Springer, 241.

[5] Wang YH, Zhang FC, Wang TS. A novel bainitic steel comparable to maraging steel in mechanical properties. Scripta Mater., 2013, 68(9): 763.

[6] Matlock DK, Bräutigam VE, Speer JG. Application of the quenching and partitioning (Q&P) process to a medium-carbon, high-Si microalloyed bar steel. Mater. Sci. Forum, 2003, 426–432, 1089.

[7] Mola J, De Cooman BC. Quenching and partitioning (Q&P) processing of martensitic stainless steels. Metall. Mater. Trans. A, 2013, 44(2): 946.

[8] Paravicini Bagliani E, Santofimia MJ, Zhao L, Sietsma J, Anelli E. Microstructure, tensile and toughness properties after quenching and partitioning treatments of a medium-carbon steel. Mater. Sci. Eng. A, 2013, 559, 486.

[9] Moor E D, Lacroix S, Clarke AJ, Penning J, Speer JG. Effect of retained austenite stabilized via quench and partitioning on the strain hardening of martensitic steels. Metall. Mater. Trans. A, 2008, 39(11): 2586.

[10] Wang Y, Zhang K, Guo ZH, Chen NL, Rong YH. A new effect of retained austenite on ductility enhancement in high strength bainitic steel. Mater. Sci. Eng. A, 2012, 552, 288.

[11] Gibbs PJ, De Moor E, Merwin MJ, Clausen B, Speer JG, Matlock DK. Austenite stability effects on tensile behavior of manganese-enriched-austenite transformation-induced plasticity steel. Metall. Mater. Trans. A, 2001, 42(12): 3691.

[12] Kim SJ, Lee CG, Choi I, Lee S. Effects of heat treatment and alloying elements on the microstructures and mechanical properties of 0.15 wt pct C transformation-induced plasticity-aided cold-rolled steel sheets. Metall. Mater. Trans. A, 2001, 32(3): 505.

[13] Park KK, Oh ST, Baeck SM, Kim DI, Han JH, Han HN, Park SH, Lee CG, Kim SJ, Oh KH. In situ deformation behavior of retained austenite in TRIP steel. Mater. Sci. Forum, 2002, 408–412, 571.

[14] ASTM E1316-05. Standard Terminology for Non Destructive Examination, 2005, PA, ASTM International

[15] Han ZY, Luo HY, Wang HW. Effects of strain rate and notch on acoustic emission during the tensile deformation of a discontinuous yielding material. Mater. Sci. Eng. A, 2011, 528(13–14): 4372.

[16] Vinogradov A, Lazarev A, Linderov M, Weidner A, Biermann H. Kinetics of deformation processes in high-alloyed cast transformation-induced plasticity/twinning-induced plasticity steels determined by acoustic emission and scanning electron microscopy: influence of austenite stability on deformation mechanisms. Acta Mater., 2013, 61(7): 2434.

[17] Mukherjee M, Mohanty ON, Hashimoto S, Hojo T, Sugimoto K. Acoustic emission technique to study the effect of strain rate on the deformation behaviour of TRIP aided steels with different matrix microstructures. ISIJ Int., 2006, 46(8): 1241.

[18] Haušild P, Davydov V, Drahokoupil J, Landa M, Pilvin P. Characterization of strain-induced martensitic transformation in a metastable austenitic stainless steel. Mater. Des., 2010, 31(4): 1821.

[19] Fallahi A, Khamedi R, Minak G, Zucchelli A. Monitoring of the deformation and fracture process of dual phase steels employing acoustic emission techniques. Mater. Sci. Eng. A, 2012, 548, 183.

[20] Santofimia MJ, Zhao L, Petrov R, Kwakernaak C, Sloof WG, Sietsma J. Microstructural development during the quenching and partitioning process in a newly designed low-carbon steel. Acta Mater., 2011, 59(15): 6059.

[21] Jacques P, Furnémont Q, Mertens A, Delannay F. On the sources of work hardening in multiphase steels assisted by transformation-induced plasticity. Philos. Mag. A, 2001, 81(7): 1789.

[22] James DR, Carpenter SH. Relationship between acoustic emission and dislocation kinetics in crystalline solids. J. Appl. Phys., 1971, 42(12): 4685.

[23] Liu GG, Cheng QC. Acoustic emission technology and its application to metal materials. Shanghai Met., 2001, 23(6): 35.

[24] Haneef TK, Mukhopadhyay CK, Rao BPC, Jayakumar T. Acoustic emissions generated during Lüders band elongation of tempered medium carbon steel. Strength Fract. Complexity, 2010, 6(4): 149.

[25] Long QY, Huazi Y. Acoustic emission during deformation of dual-phase steels. Metall. Trans. A, 1990, 21, 373.

[26] Hsu TY. The definition of martensitic transformation. Trans. Met. Heat Treat., 1996, 17(A00): 27.

[27] Clapp PC. How would we recognize a martensitic transformation if it bumped into us on a dark & austy night?. J. Phys. IV, 1995, 5, C8.

[28] Van Bohemen SMC, Sietsma J, Hermans MJM, Richardson IM. Kinetics of the martensitic transformation in low-alloy steel studied by means of acoustic emission. Acta Mater., 2003, 51(14): 4183.

[29] Van Bohemen SMC, Hermans MJM, den Ouden G, Richardson IM. A study of acoustic emission energy generated during bainite and martensite formation. J. Phys. D, 2002, 35(15): 1889.

[30] Mukhopadhyay CK, Jayakumar T, Kasiviswanathan KV, Raj B. Study of ageing-induced α′-martensite formation in cold-worked AISI type 304 stainless steel using an acoustic emission technique. J. Mater. Sci., 1995, 30(18): 4556.