Influence of silicon on the microstructures, mechanical properties and stretch-flangeability of dual phase steels

Abstract

Uniaxial tension tests and hole-expansion tests were carried out to determine the influence of silicon on the microstructures, mechanical properties, and stretch-flangeability of conventional dual-phase steels. Compared to 0.03wt% silicon, the addition of 1.08wt% silicon induced the formation of finer ferrite grains (6.8 μm) and a higher carbon content of martensite (C _m ≈ 0.32wt%). As the silicon level increased, the initial strain-hardening rate (n value) and the uniform elongation increased, whereas the yield strength, yield ratio, and stretch-flangeability decreased. The microstructures were observed after hole-expansion tests. The results showed that low carbon content martensite (C _m ≈ 0.19wt%) can easily deform in coordination with ferrite. The relationship between the mechanical properties and stretch-flangeability indicated that the steel with large post-uniform elongation has good stretch-flangeability due to a closer plastic incompatibility of the ferrite and martensite phases, which can effectively delay the production and decohesion of microvoids.

Keywords

dual-phase steel / silicon content / mechanical properties / microstructure / strain hardening

References

[1] Calcagnotto M, Ponge D, Raabe D. Effect of grain refinement to 1μm on strength and toughness of dual-phase steels. Mater. Sci. Eng. A, 2010, 527, 7832.

[2] Dong HF, Li J, Zhang Y, Park J, Yang QX. Numerical simulation on the microstress and microstrain of low Si-Mn-Nb dual-phase steel. Int. J. Miner. Metall. Mater., 2010, 17(2): 173.

[3] Lee J, Lee SJ, De Cooman BC. Effect of micro-alloying elements on the stretch-flangeability of dual phase steel. Mater. Sci. Eng. A, 2012, 536, 231.

[4] Tomita Y. Effect of morphology of second-phase martensite on tensile properties of Fe-0.1C dual phase steels. J. Mater. Sci., 1990, 25, 5179.

[5] Kumar A, Singh SB, Ray KK. Influence of bainite/martensite-content on the tensile properties of low carbon dual-phase steels. Mater. Sci. Eng. A, 2008, 474, 270.

[6] Wang ZG, Zhao AM, Zhao ZZ, Ye JY, Tang D, Zhu GS. Microstructures and mechanical properties of C-Mn-Cr-Nb and C-Mn-Si-Nb ultra-high strength dual-phase steels. Int. J. Miner. Metall. Mater., 2012, 19(10): 915.

[7] Steinbrunner DL, Matlock D, Krauss G. Void formation during tensile testing of dual phase steels. Metall. Trans. A, 1988, 19, 579.

[8] Hyun DI, Oak SM, Kang SS, Moon YH. Estimation of hole flangeability for high strength steel plates. J. Mater. Process. Technol., 2002, 130–131, 9.

[9] Kim JH, Lee MG, Kim D, Matlock DK, Wagoner RH. Hole-expansion formability of dual-phase steels using representative volume element approach with boundary-smoothing technique. Mater. Sci. Eng. A, 2010, 527, 7353.

[10] Mori KI, Abe Y, Suzui Y. Improvement of stretch flangeability of ultra high strength steel sheet by smoothing of sheared edge. J. Mater. Process. Technol., 2010, 210, 653.

[11] Sugimoto KI, Muramatsu T, Hashimoto SI, Mukai Y. Formability of Nb bearing ultra high-strength TRIP-aided sheet steels. J. Mater. Process. Technol., 2006, 177, 390.

[12] Nagasaka A, Sugimoto K, Kobayashi M. Effect of second phase morphology on warm stretch-flangeability in high strength TRIP-aided dual-phase steel sheets. ASM International (USA), New York, 1996 557

[13] Yamada Y, Koide M. Analysis of the bore-expanding test by the incremental theory of plasticity. Int. J. Mech. Sci., 1968, 10, 1.

[14] Ghadbeigi H, Pinna C, Celotto S, Yates JR. Local plastic strain evolution in a high strength dual-phase steel. Mater. Sci. Eng. A, 2010, 527, 5026.

[15] Sarwar M, Priestner R. Influence of ferrite-martensite microstructural morphology on tensile properties of dual-phase steel. J. Mater. Sci., 1996, 31, 2091.

[16] Kim S, Lee S. Effects of martensite morphology and volume fraction on quasi-static and dynamic deformation behavior of dual-phase steels. Metall. Mater. Trans. A, 2000, 31, 1753.

[17] Kim KJ, Lee S, Lee C. Effects of martensite morphology on dynamic torsional behavior in dual phase steels. Scripta Mater., 1997, 38(1): 27.

[18] Bag A, Ray KK, Dwarakadasa ES. Influence of martensite content and morphology on the toughness and fatigue behavior of high-martensite dual-phase steels. Metall. Mater. Trans. A, 2001, 32, 2207.

[19] Ahmad E, Manzoor T, Ziai MMA, Hussain N. Effect of martensite morphology on tensile deformation of dual-phase steel. J. Mater. Eng. Perform., 2012, 21(3): 382.

[20] Sudo M, Hashimoto S, Kambe S. Niobium bearing ferrite-bainite high strength hot-rolled sheet steel with improved formability. Trans. Iron Steel Inst. Jpn., 1983, 23(4): 303.

[21] Akbarpour MR, Ekrami A. Effect of ferrite volume fraction on work hardening behavior of high bainite dual phase (DP) steels. Mater. Sci. Eng. A, 2008, 477, 306.

[22] Cai MH, Ding H, Zhang JS, Li L. Effect of silicon and prior deformation of austenite on isothermal transformation in low carbon steels. Acta Metall. Sin., 2009, 22(2): 100.

[23] Cai MH, Ding H, Lee YK, Tang ZY, Zhang JS. Effects of Si on microstructural evolution and mechanical properties of hot-rolled ferrite and bainite dual-phase steels. ISIJ Int., 2011, 51(3): 476.

[24] Thomas G, Koop JY. Structure and properties of dual phase steel. The Metallurgical Society of AIME, New York, 1979

[25] Nakagawa AH, Thomas G. Microstructure-mechanical property relationships of dual-phase steel wire. Metall. Trans. A, 1985, 16, 831.

[26] Korzekwa DA, Lawson RD, Matlock DK, Krauss G. A consideration of models describing the strength and ductility of dual-phase steels. Scripta Metall., 1980, 14, 1023.

[27] Avramovic-Cingara G, Ososkov Y, Jain MK, Wilkinson DS. Effect of martensite distribution on damage behaviour in DP600 dual phase steels. Mater. Sci. Eng. A, 2009, 516, 7.

[28] Avramovic-Cingara G, Saleh ChAR, Jain MK, Wilkinson DS. Void nucleation and growth in dual-phase steel 600 during uniaxial tensile testing. Metall. Mater. Trans. A, 2009, 40, 3117.

[29] Davies RG. Influence of martensite composition and content on the properties of dual phase steels. Metall. Trans. A, 1978, 9, 671.

[30] Hollomon JH. Tensile deformation. The Metallurgical Society of AIME, New York, 1945 162

[31] Byun TS, Kim IS. Tensile properties and inhomogeneous deformation of ferrite-martensite dual-phase steels. J. Mater. Sci., 1993, 28, 2923.

[32] Bag A, Ray KK, Dwarakadasa ES. Influence of martensite content and morphology on tensile and impact properties of high-martensite dual-phase steels. Metall. Mater. Trans. A, 1999, 30, 1193.

[33] Das D, Chattopadhyay PP. Influence of martensite morphology on the work-hardening behavior of high strength ferrite-martensite dual-phase steel. J. Mater. Sci., 2009, 44, 2957.

[34] Jaoul PB. Etude de la forme des courbes de deformation plastique. J. Mech. Phys. Solids, 1957, 5, 95.

[35] Monteiro SN, Reed-Hill RE. On the double-n behavior of iron. Metall. Trans., 1971, 2(10): 2947.

[36] Samuel FH, Daniel D, Sudre O. Further investigations on the microstructure and mechanical behaviour of granular bainite in a high strength, low alloy steel: comparison of ferrite-pearlite and ferrite-martensite microstructures. Mater. Sci. Eng., 1987, 92, 43.

[37] Sankaran S, Sangal S, Padmanabhan KA. Microstructural evolution and tensile behaviour of medium carbon microalloyed steel processed through two thermomechanical routes. Mater. Sci. Technol., 2005, 21(10): 1152.

[38] Tomita Y, Okabayashi K. Mechanical properties of 0.40 pct C-Ni-Cr-Mo high strength steel having a mixed structure of martensite and bainite. Metall. Trans. A, 1985, 16, 73.

[39] Jiang ZH, Guan ZZ, Lian JS. The relationship between ductility and material parameters for dual-phase steel. J. Mater. Sci., 1993, 28, 1814.

[40] Son YI, Lee YK, Park KT, Lee CS, Shin DH. Ultrafine grained ferrite-martensite dual phase steels fabricated via equal channel angular pressing: microstructure and tensile properties. Acta Mater., 2005, 53, 3125.

[41] Tomita Y, Okabayashi K. Tensile stress-strain analysis of cold worked metals and steels and dual-phase steels. Metall. Trans. A, 1985, 16, 865.

[42] Kacem A, Krichen A, Manach PY. Occurrence and effect of ironing in the hole-flanging process. J. Mater. Process. Technol., 2011, 211, 1606.

[43] Hasegawa K, Kawamura K, Urabe T, Hosoya Y. Effects of microstructure on stretch-flange-formability of 980 MPa grade cold-rolled ultra high strength steel sheets. ISIJ Int., 2004, 44(3): 603.