Subsurface macro-inclusions and solidified hook character in aluminum-killed deep-drawing steel slabs

Abstract

Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ultralow carbon (ULC) steel slabs and two low carbon (LC) aluminum-killed steel slabs were sampled to study the relationship between hooks and subsurface macro-inclusions, which were detected on the cross-sections of steel samples with an area of 56058 mm² using an automated scanning electron microscopy/energy-dispersive X-ray spectroscopy system. Results show that subsurface inclusions larger than 200 μm were almost entrapped by hook structures, whereas the location of other inclusions smaller than 200 μm had no obvious dependence on the location of solidified hooks. Furthermore, the number density (ND) of subsurface inclusions larger than 200 μm decreased from 0.02 to 0 cm⁻² in ULC steel as the mean hook depth decreased from 1.57 to 1.01 mm. Similar trends were also observed in LC steel. In addition, the detected inclusions larger than 200 μm were concentrated in the region near the slab center (3/8 width-5/8 width), where hook depths were also larger than those at any other locations. Therefore, minimizing the hook depth is an effective way to reduce inclusion-induced sliver defects in deep-drawing steels.

Keywords

low carbon steel / aluminum-killed steel / steel sheet / deep drawing / inclusions / hooks

References

[1] Chen SH, Jiang M, He XF, Wang XH. Top slag refining for inclusion composition transform control in tire cord steel. Int. J. Miner. Metall. Mater., 2012, 19(6): 490.

[2] Shi CB, Chen XC, Guo HJ. Characteristics of inclusions in high-Al steel during electroslag remelting process. Int. J. Miner. Metall. Mater., 2012, 19(4): 295.

[3] Yang W, Wang XH, Zhang LF, Shan QL, Liu XF. Cleanliness of low carbon aluminum-killed steels during secondary refining processes. Steel Res. Int., 2013, 84(5): 473.

[4] Yang W, Wang XH, Zhang LF, Wang WJ. Characteristics of alumina-based inclusions in low carbon Al-killed steel under no-stirring condition. Steel Res. Int., 2013, 84(9): 878.

[5] Zhang QY, Wang LT, Wang XH. Influence of casting speed variation during unsteady continuous casting on non-metallic inclusions in IF steel slabs. ISIJ Int., 2006, 46(10): 1421.

[6] Wang M, Bao YP, Cui H, Wu WS, Wu HJ, Chen B, Ji CX, Zhu GS. Surface cleanliness evaluation in Ti stabilised ultralow carbon (Ti-IF) steel. Ironmaking Steelmaking, 2011, 38(5): 386.

[7] Lee GG, Thomas BG, Kim SH, Shin HJ, Baek SK, Choi CH, Kim DS, Yu SJ. Microstructure near corners of continuous-cast steel slabs showing three-dimensional frozen meniscus and hooks. Acta Mater., 2007, 55(20): 6705.

[8] Sengupta J, Thomas BG, Shin HJ, Lee GG, Kim SH. A new mechanism of hook formation during continuous casting of ultra-low-carbon steel slabs. Metall. Mater. Trans. A, 2006, 37(5): 1597.

[9] Yamamura H, Mizukami Y, Misawa K. Formation of a solidified hook-like structure at the subsurface in ultra low carbon steel. ISIJ Int., 1996, 36(Suppl.): S223.

[10] Schmidt KD, Friedel F, Imlau KP, Jager W, Muller KT. Consequent improvement of surface quality by systematic analysis of slabs. Steel Res. Int., 2003, 74(11–12): 659

[11] Itoyama S, Yamanaka H, Tanaka S, Yunde T, Kuroki T. Prediction and prevention system for sticking type breakout in continuous casting. The 71st Steelmaking Conference, Toronto, 1988 97

[12] Schwerdtfeger K, Sha H. Depth of oscillation marks forming in continuous casting of steel. Metall. Mater. Trans. B, 2000, 31(4): 813.

[13] Birat JP, Larecq M, Lamant JY, Petegnief J. The continuous casting mold: a basic tool for surface quality and strand productivity. The 74th Steelmaking Conference, Warrendale, 1991 3

[14] Sengupta J, Thomas BG, Shin HJ, Kim SH. Mechanism of hook formation in ultralow-carbon steel based on microscopy analysis and thermal-stress modeling. Iron Steel Technol., 2007, 4(7): 13

[15] Bommaraju R, Jackson T, Lucas J, Skoczylas G, Clark B. Design, development and application of mold powder to reduce slivers. The 75th Steelmaking Conference, Toronto, 1992 23

[16] Lee GG, Shin HJ, Kim SH, Kim SK, Choi WY, Thomas BG. Prediction and control of subsurface hooks in continuous cast ultra-low-carbon steel slabs. Ironmaking Steelmaking, 2009, 36(1): 39.

[17] Wada T, Suzuki M, Mori T. High speed casting of 3 meters/minute on the NKK Fukuyama Works’ No. 5 slab caster. Iron Steelmaker, 1987, 14(9): 31

[18] Toh T, Takeuchi E, Hojo M, Kawai H, Matsumura S. Electromagnetic control of initial solidification in continuous casting of steel by low frequency alternating magnetic field. ISIJ Int., 1997, 37(11): 1112.

[19] Kollberg SG, Hackl HR, Hanley PJ. Improving quality of flat rolled products using electromagnetic brake (EMBR) in continuous casting. Iron Steel Eng, 1996, 73(7): 24

[20] Awajiya Y, Kubota Y, Takeuchi S. Inclusion entrapment location in solidified shell of ultra low carbon steel slab. Association for Iron & Steel Technology 2005 Conference Proceedings, Charlotte, North Carolina, 2005 65

[21] Basu S, Choudhary SK, Girase NU. Nozzle clogging behaviour of Ti-bearing Al-killed ultra low carbon steel. ISIJ Int., 2004, 44(10): 1653.

[22] Kumar A, Choudhary SK, Ajmani SK. Distribution of macroinclusions across slab thickness. ISIJ Int., 2012, 52(12): 2305.

[23] Miki Y, Takeuchi S. Internal defects of continuous casting slabs caused by asymmetric unbalanced steel flow in mold. ISIJ Int., 2003, 43(10): 1548.

[24] Zhang LF, Rietow B, Thomas BG, Eakin K. Large inclusions in plain-carbon steel ingots cast by bottom teeming. ISIJ Int., 2006, 46(5): 670.

[25] Emling WH, Waugaman TA, Feldbauer SL, Cramb AW. Subsurface mold slag entrainment in ultra low carbon steels. The 77th Steelmaking Conference, Chicago, 1994 371

[26] Shibata H, Yin H, Yoshinaga S, Emi T, Suzuki M. In-situ observation of engulfment and pushing of nonmetallic inclusions in steel melt by advancing melt/solid interface. ISIJ Int., 1998, 38(2): 149.

[27] Zhang LF, Thomas BG. State of the art in evaluation and control of steel cleanliness. ISIJ Int., 2003, 43(3): 271.

[28] Tsai HT, Sammon WJ, Hazelton DE. Characterization and countermeasures for sliver defects in cold rolled products. The 73rd Steelmaking Conference, Detroit, 1990 49

[29] Cramb AW. Briant CL. High purity, low residual, and clean steels. Impurities in Engineered Materials: Impact, Reliability and Control, 1999, New York, Marcel Dekker Inc., 50