Precipitation behavior and martensite lath coarsening during tempering of T/P92 ferritic heat-resistant steel

Abstract

Tempering is an important process for T/P92 ferritic heat-resistant steel from the viewpoint of microstructure control, as it facilitates the formation of final tempered martensite under serving conditions. In this study, we have gained deeper insights on the mechanism underlying the microstructural evolution during tempering treatment, including the precipitation of carbides and the coarsening of martensite laths, as systematically analyzed by optical microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy. The chemical composition of the precipitates was analyzed using energy dispersive X-ray spectroscopy. Results indicate the formation of M3C (cementite) precipitates under normalized conditions. However, they tend to dissolve within a short time of tempering, owing to their low thermal stability. This phenomenon was substantiated by X-ray diffraction analysis. Besides, we could observe the precipitation of fine carbonitrides (MX) along the dislocations. The mechanism of carbon diffusion controlled growth of M₂₃C₆ can be expressed by the Zener’s equation. The movement of Y-junctions was determined to be the fundamental mechanism underlying the martensite lath coarsening process. Vickers hardness was estimated to determine their mechanical properties. Based on the comprehensive analysis of both the micro-structural evolution and hardness variation, the process of tempering can be separated into three steps.

Keywords

ferritic steel / heat resisting / tempering / precipitation / martensite / coarsening

References

[1] F. Abe, Precipitate design for creep strengthening of 9% Cr tempered martensitic steel for ultra-supercritical power plants, Sci. Technol. Adv. Mater., 9(2008), art. No. 013002.

[2] Ning BQ, Shi QZ, Yan ZS, Fu JC, Liu YC, Bie LJ. Variation of martensite phase transformation mechanism in minor-stressed T91 ferritic steel. J. Nucl. Mater., 2009, 393(1): 54.

[3] Ennis PJ, Czyrska-Filemonowicz A. Recent advances in creep-resistant steels for power plant applications. Sadhana, 2003, 28(3–4): 709.

[4] Abe F, Horiuchi T, Taneike M, Sawada K. Stabilization of martensitic microstructure in advanced 9Cr steel during creep at high temperature. Mater. Sci. Eng. A, 2004, 378(1–2): 299.

[5] Liu F, Xu G, Zhang YL, Hu HJ, Zhou LX, Xue ZL. In situ observations of austenite grain growth in Fe-C-Mn-Si super bainitic steel. Int. J. Miner. Metall. Mater., 2013, 20(11): 1060.

[6] Li JY, Zhao P, Yanagioto J, Sugiyama S, Chen YL. Effects of heat treatment on the microstructures and mechanical properties of a new type of nitrogen-containing die steel. Int. J. Miner. Metall. Mater., 2012, 19(6): 511.

[7] Lu Z, Faulkner RG, Riddle N, Martino FD, Yang K. Effect of heat treatment on microstructure and hardness of Eurofer 97, Eurofer ODS and T92 steels. J. Nucl. Mater., 2009, 386–388, 445.

[8] Abe F, Araki H, Noda T. The effect of tungsten on dislocation recovery and precipitation behavior of low-activation martensitic 9Cr steels. Metall. Trans. A, 1991, 22(10): 2225.

[9] Abe F. Effect of quenching, tempering, and cold rolling on creep deformation behavior of a tempered martensitic 9Cr-1W steel. Metall. Mater. Trans. A., 2003, 34(4): 913.

[10] Ghassemi-Armaki H, Chen RP, Maruyama K, Yoshizawa M, Igarashi M. Static recovery of tempered lath martensite microstructures during long-term aging in 9–12% Cr heat resistant steels. Mater. Lett., 2009, 63(28): 2423.

[11] Speich GR, Leslie WC. Tempering of steel. Mater. Trans., 1972, 3(5): 1043

[12] Sakasegawa H, Tamura M, Ohtsuka S, Ukai S, Tanigawa H, Kohyama A, Fujiwara M. Precipitation behavior of oxide particles in mechanically alloyed powder of oxide-dispersion-strengthened steel. J. Alloys Compd., 2008, 452(1): 2.

[13] Liu CX, Zhang DT, Liu YC, Wang Q, Yan ZS. Investigation on the precipitation behavior of M3C phase in T91 ferritic steels. Nucl. Eng. Des., 2011, 241, 2411.

[14] Hutchinson B, Hagström J, Karlsson O, Lindell D, Tornberg M, Lindberg F, Thuvander M. Microstructures and hardness of as-quenched martensites (0.1–0.5%C). Acta Mater., 2011, 59(14): 5845.

[15] Ghosh G, Olson GB. Precipitation of paraequilibrium cementite: Experiments, and thermodynamic and kinetic modeling. Acta Mater., 2002, 50(8): 2099.

[16] Gustafson Hättestrand M. Coarsening of precipitates in an advanced creep resistant 9% chromium steel quantitative microscopy and simulations. Materi. Sci. Eng. A., 2002, 333(1–2): 279.

[17] Wang YN, Bao YP, Wang M, Zhang LC. Precipitation and control of BN inclusions in 42CrMo steel and their effect on machinability. Int. J. Miner. Metall. Mater., 2013, 20(9): 842.

[18] Yamada K, Igarashi M, Muneki S, Abe F. Creep properties affected by morphology of MX in high-Cr ferritic steels. ISIJ. Int., 2001, 41, s116.

[19] Singhal LK, Martin JW. The nucleation and growth of widmannstätten M₂₃C₆ precipitation in an austenitic stainless steel. Acta Metall., 1968, 16, 1159.

[20] Zener C. Theory of growth of spherical precipitates from solid solution. J. Appl. Phys., 1949, 20, 950.

[21] Xu LQ, Zhang DT, Liu YC, Ning BQ, Qiao ZX, Yan ZS, Li HJ. Precipitation kinetics of M₂₃C₆ in T/P92 heat-resistant steel by applying soft-impingement correction. J. Mater. Res., 2013, 28(11): 1529.

[22] Brandes EA. Smithells Metals Reference Book, 1983, London, Butterworths, 13

[23] Guo J, Qu HW, Liu LG, Sun YL, Zhang Y, Yang QX. Study on stable and meta-stable carbides in a high speed steel for rollers during tempering processes. Int. J. Miner. Metall. Mater., 2013, 20(2): 146.

[24] Sawada K, Taneike M, Kimura K, Abe F. In situ observation of recovery of lath structure in 9% chromium creep resistant steel. Mater. Sci. Technol., 2003, 19, 739.

[25] Abe F. Coarsening behavior of lath and its effect on creep rates in tempered martensitic 9Cr-W steels. Mater. Sci. Eng. A, 2004, 387–389, 565.

[26] Krauss G. Martensite in steel: strength and structure. Mater. Sci. Eng. A, 1999, 273–275, 40.