Effect of electric pulse on the crystal structure of solidified copper ingots

Abstract

To obtain advanced quality pure copper, the microstructure of solidified copper was optimized by imposing electric pulse on liquid copper in this study. Experiments were performed to determine the effect of electric pulse voltage, arrangement mode of electrodes, and energy input on the microstructure of solidified copper. The results show that, when the energy input of electric pulse is bigger than 28.95 kJ per ton copper, the percent of fine grains increases noticeably with the increase of energy input; but when the energy input of electric pulse is smaller than 28.95 kJ per ton copper, the percent of fine grains decreases with the increase of energy input. The influence order of above factors on grain refinement is electric pulse voltage > arrangement mode of electrodes > energy input. According to the above experimental results, the optimum process conditions are chosen as the voltage being 400 V and the energy input greater than 28.95 kJ per ton copper. Meanwhile, the best arrangement mode of electrodes should be that, one electrode is immerged in the middle of liquid copper in the crystallizer, and the other is connected to the inner wall of the crystallizer, which is divided into two electrode poles for the symmetrical electric field distribution.

Keywords

copper / solidification / crystal structure / electric pulse

References

[1] Wen HQ, Ma XJ, Zhou YM, Zhang YJ. Effect of pulse current on carbon steel’s solidification structure. Baosteel Technol., 2003, 6, 51.

[2] Misra AK. A novel solidification technique of metals and alloys: under the influence of applied potential. Metall. Trans. A, 1985, 16, 1354.

[3] Misra AK. Effect of electric potentials on solidification of near eutectic Pb-Sb-Sn alloy. Mater. Lett., 1986, 4, 176.

[4] Li LZ. The Theory and Discussion of Electric Pulse Imposing on Metal Solidification Organization and Solidification Processing, 2006, Beijing, University of Science and Technology Beijing, 42.

[5] Wang JZ, Cang DQ, Tang Y. The influence of electric pulse inoculating to Al-5.0% Cu alloy solidification structure. Foundry, 1999, 5, 4.

[6] Conrad H. Influence of an electric or magnetic field on the liquid-solid transformation in materials and on the microstructure of the solid. Mater. Sci. Eng. A, 2000, 287, 205.

[7] Liu WB, Li N, Wen YH, Zhang SC, Yang SZ. Effects of amount of pre-deformation on precipitation of NbC particles and shape memory effect of Fe₁₇Mn₅Si₈Cr₅Ni_0.5NbC alloy during electropulsing treatment. Trans. Nonferrous Met. Soc. China, 2012, 22(Suppl.1): 193.

[8] Xue QG, Sun W, Wang JS, Cao LJ, Wu HY, Wang JH. Effect of electro-pulse modification on the growth kinetics of hot dip galvanizing. J. Univ. Sci. Technol. Beijing, 2012, 34, 783.

[9] Yang SZ, Li N, Wen YH, Peng HB, Liu WB. Effect of electropulsing ageing on microstructure and shape memory effect in Fe₁₄Mn₆Si₈Cr₅Ni alloy. J. Funct. Mater., 2012, 43(3): 401.

[10] Sun HY, Wang JS, Cao LJ, Xue QG. Effect of electropulsing treatment on thermal stability and annealing crystallization of Zr-based bulk amorphous alloy. Trans. Mater. Heat Treat., 2012, 33, 1.

[11] Li ZL, Wu ZF, Wang F. Anodic/cathodic electrical pulse treatment of stainless steel in various mediums and its influence on corrosion resistance. Corros. Prot., 2012, 33, 8.

[12] Li QY, Zhu CL, Bai T. Simplification of de-icing excitation and influential factors of the electro-impulse deicing system. Acta Aeronaut. Astronaut. Sin., 2012, 33, 1384.

[13] Jiang YB, Tang GY, Shek CH, Xie JX, Xu ZH, Zhang ZH. Mechanism of electropulsing induced recrystallization in a cold-rolled Mg-9Al-1Zn alloy. J. Alloys Compd., 2012, 536, 94.

[14] Song H, Wang ZJ. Improvement of mechanical properties of cold-rolled commercially pure Ti sheet by high density electropulsing. Trans. Nonferrous Met. Soc. China, 2012, 22, 1350.

[15] Song H, Wang ZJ. Effect of electropulsing on dislocation mobility of titanium sheet. Trans. Nonferrous Met. Soc. China, 2012, 22, 1599.

[16] Qi JG, Dai S, Zhao ZF, Zhang DJ, Wang JZ, Cang DQ. Model of solidification characteristics of Cu-Al alloy modified by electric pulse. Chin. J. Nonferrous Met., 2012, 22, 224.