Injection molding and debinding of micro gears fabricated by micro powder injection molding

Abstract

Micro powder injection molding (μPIM) was investigated for possible mass production of micro-components at relatively low cost. However, scaling down to such a level produces challenges in injection molding and debinding. Micro gears were fabricated by μPIM from in-house feedstock. The effect of injection speed and injection pressure on the replication of the micro gear cavity was investigated. Solvent debinding and thermal debinding processes were discussed. The results show that micro gears can be successfully fabricated under the injection pressure of 70 MPa and the 60% injection speed. Either too low or too high injection speed can cause incomplete filling of micro gears. The same is the case with too low injection pressure. Too high injection pressure can bring cracks. Solvent debinding of micro gears was performed in a mixture of petroleum ether and ethanol. Subsequently, micro gears were successfully debound by a multistep heating schedule.

Keywords

gear manufacture / micro gears / injection molding / debinding / zirconia

References

[1] Meng J., Loh N.H., Fu G., Tay B.Y., Tor S.B. Micro powder injection moulding of alumina micro-channel part. J. Eur. Ceram. Soc., 2011, 31(6): 1049.

[2] Tay B.Y., Loh N.H., Tor S.B., Ng F.L., Fu G., Lu X.H. Characterisation of micro gears produced by micro powder injection moulding. Powder Technol., 2009, 188(3): 179.

[3] Imgrund P., Rota A., Simchi A. Microinjection moulding of 316L/17-4PH and 316L/Fe powders for fabrication of magnetic-nonmagnetic bimetals. J. Mater. Process. Technol., 2008, 200(1–3): 259.

[4] Yin H.Q., Qu X.H., Jia C.C. Fabrication of micro gear wheels by micropowder injection molding. J. Univ. Sci. Technol. Beijing, 2008, 15(4): 480.

[5] Li S.G., Fu G., Reading I., Tor S.B., Loh N.H., Chaturvedi P., Yoon S.F., Toumi K.Y. Dimensional variation in production of high-aspect-ratio micro-pillars array by micro powder injection molding. Appl. Phys. A, 2007, 89(3): 721.

[6] Yin H.Q., Du M.N., Qu X.H., He X.B., Jia C.C. Manufacturing technology and performance testing of metallic micro-sized components. J. Univ. Sci. Technol. Beijing, 2008, 30(12): 1428.

[7] Wu R.Y., Wei W.C.J. Kneading behaviour and homogeneity of zirconia feedstocks for micro-injection molding. J. Eur. Ceram. Soc., 2004, 24(14): 3653.

[8] Loh N.H., Tor S.B., Tay B.Y., Murakoshi Y., Maeda R. Fabrication of micro gear by micro powder injection molding. Microsyst. Technol., 2008, 14(1): 43.

[9] Tseng W.J., Chiang D. Influence of molding variables on defect formation and mechanical strength of injection-molded ceramics. J. Mater. Process. Technol., 1998, 84(1–3): 229.

[10] Tseng W.J., Hsu C.K. Cracking defect and porosity evolution during thermal debinding in ceramic injection moldings. Ceram. Int., 1999, 25(5): 461.

[11] Krug S., Evans J.R.G., Maat J.H.H. T. Residual stresses and cracking in large ceramic injection mouldings subjected to different solidification schedules. J. Eur. Ceram. Soc., 2000, 20(14–15): 2535.

[12] Tsai K.M., Hsieh C.Y., Lo W.C. A study of the effects of process parameters for injection molding on surface quality of optical lenses. J. Mater. Process. Technol., 2009, 209(7): 3469.

[13] Chen C.S., Chen S.C., Liao W.H., Chien R.D., Lin S.H. Micro injection molding of a micro-fluidic platform. Int. Commun. Heat Mass Transfer, 2010, 37(9): 1290.

[14] Fu G., Loh N.H., Tor S.B., Murakoshi Y., Maeda R. Replication of metal microstructures by micro powder injection molding. Mater. Des., 2004, 25(8): 729.

[15] Fu G., Loh N.H., Tor S.B., Tay B.Y., Murakoshi Y., Maeda R. Injection molding, debinding and sintering of 316L stainless steel microstructures. Appl. Phys. A, 2005, 81(3): 495.

[16] Omar M.A., Ibrahim R., Sidik M.I., Mustapha M., Mohamad M. Rapid debinding of 316 L stainless steel injection moulded component. J. Mater. Process. Technol., 2003, 140(1–3): 397.

[17] Merz L., Rath S., Piotter V., Ruprecht R., Kleissl J. R.-, Hausselt J. Feedstock development for micro powder injection molding. Microsyst. Technol., 2002, 8(2–3): 129.

[18] Huang B.Y., Liang S.Q., Qu X.H. The rheology of metal injection molding. J. Mater. Process. Technol., 2003, 137(1–3): 132.