Effect of inclusion size on the high cycle fatigue strength and failure mode of a high V alloyed powder metallurgy tool steel

Abstract

The fatigue strength of a high V alloyed powder metallurgy tool steel with two different inclusion size levels, tempered at different temperatures, was investigated by a series of high cycle fatigue tests. It was shown that brittle inclusions with large sizes above 30 μm prompted the occurrence of subsurface crack initiation and the reduction in fatigue strength. The fracture toughness and the stress amplitude both exerted a significant influence on the fish-eye size. A larger fish-eye area would form in the sample with a higher fracture toughness subjected to a lower stress amplitude. The stress intensity factor of the inclusion was found to lie above a typical value of the threshold stress intensity factor of 4 MPa·m^1/2. The fracture toughness of the sample with a hardness above HRC 56 could be estimated by the mean value of the stress intensity factor of the fish-eye. According to fractographic evaluation, the critical inclusion size can be calculated by linear fracture mechanics.

Keywords

powder metallurgy / tool steel / fatigue of materials / strength of materials / failure modes / inclusions / fractography

References

[1] Meurling F., Melander A., Tidesten M., Westin L. Influence of carbide and inclusion contents on the fatigue properties of high speed steels and tool steels. Int. J. Fatigue, 2001, 23, 215

[2] Danninger H., Weiss B. The influence of defects on high cycle fatigue of metallic materials. J. Mater. Process. Technol., 2003, 143–144, 179

[3] Torres Y., Rodríguez S., Mateo A., Anglada M., Llanes L. Fatigue behavior of powder metallurgy high-speed steel: fatigue limit prediction using a crack growth threshold-based approach. Mater. Sci. Eng. A, 2004, 387–389, 501.

[4] Wang X.S., Zhang L.N., Zeng Y.P., Xie X.S. SEM in-situ investigation on fatigue cracking behavior of P/M Rene95 alloy with surface inclusions. J. Univ. Sci. Technol. Beijing, 2006, 13(13): 244

[5] Sohar C.R., Betzwar-Kotas A., Gierl C., Danninger H., Weiss B. Gigacycle fatigue response of tool steels produced by powder metallurgy compared to ingot metallurgy tool steel. Int. J. Mater. Res., 2010, 101, 1140

[6] Murakami Y., Endo M. Effects of defects, inclusions and inhomogeneities on fatigue strength. Fatigue, 1994, 16, 163

[7] Tchuindjang J. T., Lecomte-Beckers J. Fractography survey on high cycle fatigue failure: Crack origin characterization and correlations between mechanical tests and microstructure in Fe-C-Cr-Mo-X alloys. Int. J. Fatigue, 2007, 29, 713

[8] V. Kazymyroych, J. Ekengren, J. Bergström, and C. Burman, Evaluation of the giga-cycle fatigue strength, crack initiation and growth in high strength H13 tool steel, [in] Proceedings of Fourth International Conference on Very High Cycle Fatigue (VHCF-4), Michigan, 2007, p.209.

[9] Medvedeva A., Bergstróm J., Gunnarsson S. Inclusions, stress concentrations and surface condition in bending fatigue of an H13 tool steel. Steel Res. Int., 2008, 79(5): 376.

[10] Liu Y.B., Yang Z.G., Li Y.D., Chen S.M., Li S.X., Hui W.J., Weng Y.Q. Dependence of fatigue strength on inclusion size for high-strength steels in very high cycle fatigue regime. Mater. Sci. Eng. A, 2009, 517, 180

[11] Murakami Y., Kodama S., Konuma S. Quantitative evaluation of effects of non-metallic inclusions on fatigue strength of high strength steels: I. Basic fatigue mechanism and evaluation of correlation between the fatigue fracture stress and the size and location of non-metallic inclusion. Int. J. Fatigue, 1989, 11, 291

[12] Furuya Y., Matsuoka S., Abe T. Inclusion-controlled fatigue properties of 1800 MPa-class spring steels. Metall. Mater. Trans. A, 2004, 35, 3737

[13] Yang Z.G., Li S.X., Li Y.D., Liu Y.B., Hui W.J., Weng Y.Q. Relationship among fatigue life, inclusion size and hydrogen concentration for high-strength steel in the VHCF regime. Mater. Sci. Eng. A, 2010, 527, 559

[14] Tanaka K., Akiniwa Y. Fatigue crack propagation behavior derived from S-N data in very high cycle regime. Fatigue Fract. Eng. Mater. Struct., 2002, 25, 775

[15] Wang Q.Y., Bathias C., Kawagoishi N., Chen Q. Effect of inclusion on subsurface crack initiation and gigacycle fatigue strength. Int. J. Fatigue, 2002, 24, 1269

[16] Shiozawa K., Morii Y., Nishino S., Lu L. Subsurface crack initiation and propagation mechanism in high-strength steel in a very high cycle fatigue regime. Int. J. Fatigue, 2006, 28, 1521

[17] Sohar C.R., Betzwar-Kotas A., Gierl C., Weiss B., Danninger H. Gigacycle fatigue behavior of a high chromium alloyed cold work tool steel. Int. J. Fatigue, 2008, 30, 1137

[18] Sohar C.R., Betzwar-Kotas A., Gierl C., Weiss B., Danninger H. Fatigue behavior of M2 and M42 high speed steel up to the gigacycle regime. Kovove Mater., 2009, 47, 147.

[19] Yao J., Qu X.H., Rafi-ud-din He X.B., Zhang L. Effect of inclusion on high cycle fatigue response of a powder metallurgy tool steel. J. Cent. South Univ. Technol., 2012, 19, 1773

[20] Yao J., Qu X.H., He X.B., Zhang L. Inclusion-controlled high cycle fatigue behavior of a high V alloyed powder metallurgy cold-working tool steel. Mater. Sci. Eng. A, 2011, 528, 4180

[21] Sohar C.R., Betzwar-Kotas A., Gierl C., Weiss B., Danninger H. Fractographic evaluation of gigacycle fatigue crack nucleation and propagation of a high Cr alloyed cold work tool steel. Int. J. Fatigue, 2008, 30, 2191

[22] Fukaura K., Yokoyama Y., Yokoi D., Tsujii N., Ono K. Fatigue of cold-work tool steels: Effect of heat treatment and carbide morphology on fatigue crack formation, life, and fracture surface observations. Metall. Mater. Trans. A, 2004, 35, 1289

[23] Murakami Y. Stress Intensity Factors Handbook, 1987, New York, Oxford Press, 668.