Impact of surface irregularities on coal wall stability and support mechanisms: Insights from physical and numerical experiments

Abstract

Coal wall stability is a critical factor influencing coal mining efficiency and threatens the safety of working faces, where irregular coal wall surfaces significantly affect the contact and support effectiveness of the support plate, thereby impacting stability. Through a combination of theoretical analysis, mechanical testing, and numerical simulations, this study establishes a mechanical model of irregular coal wall surfaces to investigate the effects of the undulation period and undulation height on coal wall failure characteristics. This research reveals the mechanical response mechanisms of irregular coal wall surfaces and proposes an innovative method to enhance coal wall stability by improving the supporting cushion material of the support plate, which was validated through numerical simulations. The results show that the undulation height and undulation period significantly influence the macroscopic mechanical parameters of the samples, with the undulation height exerting a more pronounced effect. The strength of the samples with undulating surfaces is approximately 50%-60% that of the samples with flat surfaces. The failure mode under uniaxial compression is predominantly tensile, resulting in long and slender block fragments with a characteristic “III”-shaped tensile fracture pattern. During the loading process, samples with undulating surfaces dissipate energy at all stages, with a greater proportion of energy dissipation occurring during the early loading stage because of structural damage and the formation of internal cracks. The surface compressive and tensile stresses are correlated with the curvature radius of the convex surface and the elastic modulus of the supporting plate. Reducing the elastic modulus of the supporting plate material can effectively alleviate the stress concentration at convex locations and increase the peak strength. This study provides theoretical foundations and technical references for the prevention and control of coal wall spalling in deep thick coal seam mining.

Keywords

Coal wall spalling / Undulation height / Undulation period / Contact area / Support plate

Acknowledgments

The authors gratefully acknowledge financial support from the National Key Research and Development Program of China (Nos. 2023YFC2907501 and 2023YFC2907503), the National Natural Science Foundation of China (Nos. 52374106 and 52274154), and the Fundamental Research Funds for the Central Universities (No. 2023YQTD02).

References

[1] Wang JC.Fully mechanized longwall top coal caving technology in China and discussion on issues of further development. Coal Sci Technol 2005; 33 (1):14-7. In Chinese.

[2] Wang JC.Thick coal seam mining theory and technology. Beijing: Metallurgical Industry Press; 2009.

[3] Pang YH, Wang GF. Hydraulic support with large mining height structural optimal design and adaptability analysis. J China Coal Soc 2017; 42 (10):2518-27. In Chinese.

[4] Xu YX, Wang GF, Li MZ, Xu YJ, Han HJ, Zhang JH. Investigation on coal face slabbed spalling features and reasonable control at the longwall face with super large cutting height and longwall top coal caving method. J China Coal Soc 2021; 46(2):357-69. In Chinese.

[5] Wang XQ. Jointed coal mass model reconstruction and its mechanical response characteristics. Doctoral dissertation. Beijing: China University of Mining and Technology (Beijing); 2017. In Chinese.

[6] Bai LW. Mechanical response and failure characteristics of coal-rock combination under different loading rates. Min Saf Environ Prot 2024; 51:1-6. In Chinese.

[7] Chi GM, Li G, Zhang CH, Xu G. Analytical solution of predicting rib spalling depth of fully-mechanized coal working face based on tri-linear strain softening model. Coal Sci Technol 2024; 52(7):1-10. In Chinese.

[8] Xue B, Zhang WS, Wang C. Determination of working resistance of support parameter variation of large mining height support: the case of Caojiatan coal mine. Geomech Geophys Geo Energy Geo Resour 2024; 10(1):1.

[9] Kong D, Xiong Y, Cheng ZB, Wang N, Wu GY, Liu Y.Stability analysis of coal face based on coal face-support-roof system in steeply inclined coal seam. Geomech Eng 2021; 25:233-43.

[10] Xu YJ, Du YB. Research and application of coal wall limit stability height based on wedge model. Rock Mech Eng 2022; 41(S2):3240-9. In Chinese.

[11] Chang QL, Yuan CL, Wang YZ, Zhang B, Zhou HQ. Semi-convex mechanical analysis on stability of step coal wall in fully mechanized mining with paste filling. J China Univ Min Technol 2022; 51(1):46-55. In Chinese.

[12] Chang QL, Leng Q, Yuan CL, Zhou HQ, Zhang B. Study on bearing characteristics of filling paste and coal in steeply inclined extra-thick coal seams with large mining height and horizontal stratification. J Min Saf Eng 2021; 38(5):919-28. In Chinese.

[13] Li GS, Li ZH, Du F, Cao ZZ. Mechanical mechanism of rib spalling and sensitivity analysis of gangue parameters to rib spalling in gangue-bearing coal seams. Environ Sci Pollut Res Int 2023; 30(13):38713-27.

[14] Zhang JH, Li MZ, Yang ZK, Li TJ, Xu YX, Zeng MS, Xin JX. Mechanism of coal wall spalling in super high fully mechanized face and its multi-dimensional protection measures. J Min Saf Eng 2021; 38(3):487-95. In Chinese.

[15] Yang K, Liu S, Tang CA, Wei Z, Chi XL. Mechanism and prevention of coal seam rib spalling in remote protected layer across coal group. J China Coal Soc 2019; 44(9):2611-21. In Chinese.

[16] Wang HW, Wu YP, Jiao JQ, Cao PP. Stability mechanism and control technology for fully mechanized caving mining of steeply inclined extra-thick seams with variable angles. Min Metall Explor 2021; 38(2):1047-57.

[17] Xu YX, Wang GF, Li MZ, Xu YJ, Zhou CT, Zhang JH. Mechanism of slabbed spalling failure of the coal face in fully mechanized caving face with super large cutting height. J Min Saf Eng 2021; 38(1):19-30. In Chinese.

[18] Ma ZR. Study on co-existence mechanism of tensile-shear failure of rib spalling in large mining height working face. Coal Sci Technol 2020; 48(12):81-7. In Chinese.

[19] Wang HW, Wu YP, Jiao JQ, Luo SH, Liu KZ, Xie PS, Liu MF. Study on effect of dip angle on coal wall spalling of working face with great mining height in steeply inclined coal seam. J Min Saf Eng 2019; 36(4):728-35,752. In Chinese.

[20] Pang YH, Wang GF, Ren HW. Multiple influence factor sensitivity analysis on coal wall spalling of workface with large mining height. J Min Saf Eng 2019; 36 (4):736-45. In Chinese.

[21] Wang JC, Wang ZH.Systematic principles of surrounding rock control in longwall mining within thick coal seams. Int J Min Sci Technol 2019; 29 (1):65-71.

[22] Wang ZH, Wang JC, Yang Y, Tang YS, Wang L.Mechanical relation between support stiffness and longwall face stability within fully-mechanized mining faces. J China Univ Min Technol 2019; 48(2):258-67. In Chinese.

[23] Yao QL, Li XH, Sun BY, Ju MH, Chen T, Zhou J, Liang S, Qu Q. Numerical investigation of the effects of coal seam dip angle on coal wall stability. Int J Rock Mech Min Sci 2017; 100:298-309.

[24] Yu X, Wei WJ, Li Z, Li MZ, Wu SX. Stability analysis and failure control of a longwall panel with a large mining height considering fracture distribution. Bull Eng Geol Environ 2023; 82(2):54.

[25] Guo J, Huang WB, Feng GR, Bai JW, Li LR, Wang Z, Yu LY, Wen XZ, Zhang J, Feng WM. Stability analysis of longwall top-coal caving face in extra-thick coal seams based on an innovative numerical hydraulic support model. Int J Min Sci Technol 2024; 34(4):491-505.

[26] Tian ML, Han LJ, Xiao HT, Meng QB. Experimental study of deformations and failures of the coal wall in a longwall working face. Eng Fail Anal 2021; 125:105428.

[27] Chen BB, Liu CY, Wu FF. A deep-hole microblasting technique for controlling coal wall spalling during mining of a vertically jointed seam. Energy Sci Eng 2022; 10(7):2253-67.

[28] Xiong Y, Kong DZ, Cheng ZB, Wu GY, Zhang Q.The comprehensive identification of roof risk in a fully mechanized working face using the cloud model. Mathematics 2021; 9(17):2072.

[29] Wu XG, Wang MY, Lu H, Zhang YJ, Nie W. Modified Sadowski formula-based model for the slope shape amplification effect under multistage slope blasting vibration. Int J Min Sci Technol 2024; 34(5):631-41.

[30] Whitehouse DJ. Handbook of surface metrology. New York: Institute of Physics Publishing; 1994.

[31] British Standards Institution and International Organization for Standardization. Geometrical Product Specifications (GPS)-Surface Texture: Profile Method-Terms, Definitions and Surface Texture Parameters. English; 2009.

[32] Hu QT, Zhang ST, Wen GC, Dai LC, Wang B. Coal-like material for coal and gas outburst simulation tests. Int J Rock Mech Min Sci 2015; 74:151-6.