MSTMM-Validated Machining Efficiency and Surface Roughness Improvement Using Evolutionary Optimization Algorithm

Abstract

Ultra-precision machining (UPM) has been extensively employed for the production of high-end precision components. The process is highly precise, and the associated cost of production is also high. Optimization of machining parameters in UPM can significantly improve machining efficiency and surface roughness. This study proposes an innovative approach that couples transfer matrix methods for multibody systems (MSTMM) and particle swarm optimization (PSO) to optimize the machining parameters, aiming to simultaneously improve the machining efficiency and surface roughness of UPM machined components. Initially, the dynamic model of an ultra-precision fly-cutting (UPFC) machine tool was developed using MSTMM and validated by machining tests. Subsequently, the PSO algorithm was employed to optimize the machining parameters. Based on the optimized parameters, a 40% reduction in machining time and an 18.6% improvement in surface roughness peak-to-valley (PV) value have been achieved. The proposed method and the optimized parameters were verified through simulations using the MSTMM model, resulting in a minimal error of only 0.9%.

Keywords

machining efficiency / particle swarm optimization / transfer matrix methods for multibody systems / ultra-precision fly cutting

References

[1] W. S. Yip, H. E. Yan, B. Zhang, and S. To, “The State-of-Art Review of Ultra-Precision Machining Using Text Mining: Identification of Main Themes and Recommendations for the Future Direction,” WIREs Data Mining and Knowledge Discovery 14, no. 1 (2024): e1517.

[2] S. J. Zhang, S. To, S. J. Wang, and Z. W. Zhu, “A Review of Surface Roughness Generation in Ultra-Precision Machining,” International Journal of Machine Tools and Manufacture 91 (2015): 76–95.

[3] S. J. Zhang, S. To, Z. W. Zhu, and G. Q. Zhang, “A Review of Fly Cutting Applied to Surface Generation in Ultra-Precision Machining,” International Journal of Machine Tools and Manufacture 103 (2016): 13–27.

[4] H. Park, B. Qi, D.-V. Dang, and D. Y. Park, “Development of Smart Machining System for Optimizing Feedrates to Minimize Machining Time,” Journal of Computational Design and Engineering 5, no. 3 (2018): 299–304.

[5] X. Chen, C. Li, Y. Tang, L. Li, Y. Du, and L. Li, “Integrated Optimization of Cutting Tool and Cutting Parameters in Face Milling for Minimizing Energy Footprint and Production Time,” Energy 175 (2019): 1021–1037.

[6] P. Vavruska, P. Zeman, and M. Stejskal, “Reducing Machining Time by Pre-Process Control of Spindle Speed and Feed-Rate in Milling Strategies,” Procedia CIRP 77 (2018): 578–581.

[7] P. Pangestu, E. Pujiyanto, and C. N. Rosyidi, “Multi-Objective Cutting Parameter Optimization Model of Multi-Pass Turning in CNC Machines for Sustainable Manufacturing,” Heliyon 7 (2021): e06043.

[8] J. Zhang, X. Han, L. Li, et al., “Multi-Objective Optimisation for Energy Saving and High Efficiency Production Oriented Multidirectional Turning Based on Improved Fireworks Algorithm Considering Energy, Efficiency and Quality,” Energy 284 (2023): 129205.

[9] Y. Li, J. Chen, Y. Wang, et al., “Multi-Objective Modeling and Evaluation for Energy Saving and High Efficiency Production Oriented Multidirectional Turning Considering Energy, Efficiency, Economy and Quality,” Energy 294 (2024): 130780.

[10] N. A. Zolpakar, M. F. Yasak, and S. Pathak, “A Review: Use of Evolutionary Algorithm for Optimisation of Machining Parameters,” International Journal of Advanced Manufacturing Technology 115, no. 1 (2021): 31–47.

[11] J. Nayak, H. Swapnarekha, B. Naik, G. Dhiman, and S. Vimal, “25 Years of Particle Swarm Optimization: Flourishing Voyage of Two Decades,” Archives of Computational Methods in Engineering 30, no. 3 (2023): 1663–1725.

[12] S. Zahoor, W. Abdul-Kader, A. Shehzad, and M. S. Habib, “Milling of Inconel 718: An Experimental and Integrated Modeling Approach for Surface Roughness,” Journal of Advanced Manufacturing Technology 120, no. 3 (2022): 1609–1624.

[13] Y. Chen, L. Chen, C. Huang, Y. Lu, and C. Wang, “A Dynamic Tire Model Based on HPSO-SVM,” International Journal of Agricultural and Biological Engineering 12, no. 2 (2019): 36–41.

[14] H. Jiang, W. Xu, and Q. Chen, “Evaluating Aroma Quality of Black Tea by an Olfactory Visualization System: Selection of Feature Sensor Using Particle Swarm Optimization,” Food Research International 126 (2019): 108605.

[15] Z. Guo, A. O. Barimah, A. Shujat, et al., “Simultaneous Quantification of Active Constituents and Antioxidant Capability of Green Tea Using NIR Spectroscopy Coupled With Swarm Intelligence Algorithm,” LWT 129 (2020): 109510.

[16] E. Bonah, X. Huang, R. Yi, J. H. Aheto, R. Osae, and M. Golly, “Electronic Nose Classification and Differentiation of Bacterial Foodborne Pathogens Based on Support Vector Machine Optimized With Particle Swarm Optimization Algorithm,” Journal of Food Process Engineering 42, no. 6 (2019): e13236.

[17] H. Jiang, T. Liu, P. He, Y. Ding, and Q. Chen, “Rapid Measurement of Fatty Acid Content During Flour Storage Using a Color-Sensitive Gas Sensor Array: Comparing the Effects of Swarm Intelligence Optimization Algorithms on Sensor Features,” Food Chemistry 338 (2021): 127828.

[18] Y. Ding, Y. Yan, J. Li, X. Chen, and H. Jiang, “Classification of Tea Quality Levels Using Near-Infrared Spectroscopy Based on CLPSO-SVM,” Foods 11, no. 11 (2022): 1658.

[19] R. Lmalghan, M. C. K. Rao, A. S, S. S. Rao, and M. A. Herbert, “Machining Parameters Optimization of AA6061 Using Response Surface Methodology and Particle Swarm Optimization,” International Journal of Precision Engineering and Manufacturing 19, no. 5 (2018): 695–704.

[20] K. Bousnina, A. Hamza, and N. Ben Yahia, “A Combination of PSO-ANN Hybrid Algorithm and Genetic Algorithm to Optimize Technological Parameters During Milling 2017A Alloy,” Journal of Industrial and Production Engineering 40, no. 7 (2023): 554–571.

[21] S. Bharathi Raja and N. Baskar, “Application of Particle Swarm Optimization Technique for Achieving Desired Milled Surface Roughness in Minimum Machining Time,” Expert Systems With Applications 39, no. 5 (2012): 5982–5989.

[22] L. N. Abdulkadir, K. Abou-El-Hossein, P. B. Odedeyi, M. M. Liman, and A. I. Jumare, “RSM and MD—A Roughness Predictive Model and Simulation Comparison of Monocrystalline Optical Grade Silicon,” International Journal of Advanced Manufacturing Technology 112 (2021): 437–451.

[23] K.-E. Tang, Y.-C. Huang, W.-T. Lin, Y.-C. Cheng, and C.-W. Liu, “Optimization of Single-Point Diamond Turning Processes for Single Crystal Calcium Fluoride: A Surrogate Model for Surface Roughness Prediction,” International Journal of Advanced Manufacturing Technology 136, no. 2 (2025): 775–787.

[24] H. Lu, X. Rui, Z. Ma, et al., “Hybrid Multibody System Method for the Dynamic Analysis of an Ultra-Precision Fly-Cutting Machine Tool,” International Journal of Mechanical System Dynamics 2, no. 3 (2022): 290–307.

[25] Y. Liang, W. Chen, Q. Bai, et al., “Design and Dynamic Optimization of an Ultraprecision Diamond Flycutting Machine Tool for Large KDP Crystal Machining,” International Journal of Advanced Manufacturing Technology 69 (2013): 237–244.

[26] W. Chen, L. Lu, K. Yang, H. Su, and G. Chen, “An Experimental and Theoretical Investigation Into Multimode Machine Tool Vibration With Surface Generation in Flycutting,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 230, no. 2 (2016): 381–386.

[27] C. H. An, Y. Zhang, Q. Xu, et al., “Modeling of Dynamic Characteristic of the Aerostatic Bearing Spindle in an Ultra-Precision Fly Cutting Machine,” International Journal of Machine Tools and Manufacture 50, no. 4 (2010): 374–385.

[28] Y. Liang, W. Chen, C. An, X. Luo, G. Chen, and Q. Zhang, “Investigation of the Tool-Tip Vibration and Its Influence Upon Surface Generation in Flycutting,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 228, no. 12 (2014): 2162–2167.

[29] C. Deng, C. An, B. Wei, and J. Miao, “Investigation on the Influence of Aerostatic Pressure Upon Surface Generation in Flycutting,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 233, no. 4 (2019): 1136–1143.

[30] A. Shehzad, X. Rui, Y. Ding, et al., “Tool-Tip Vibration Prediction Based on a Novel Convolutional Enhanced Transformer,” International Journal of Mechanical System Dynamics 4, no. 1 (2024): 34–47.

[31] A. Shehzad, X. Rui, Y. Ding, et al., “Deep-Learning-Assisted Online Surface Roughness Monitoring in Ultraprecision Fly Cutting,” Science China: Technological Sciences 67 (2024): 1482–1497.

[32] A. Shehzad, X. Rui, Y. Ding, et al., “Surface Quality Predictive Model for Ultraprecision Fly-Cutting Based on an Integrated Hybrid CNN-LSTM,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture (2024): 09544054241306246, https://journals.sagepub.com/doi/abs/10.1177/09544054241306246.

[33] X. Rui, J. Zhang, X. Wang, B. Rong, B. He, and Z. Jin, “Multibody System Transfer Matrix Method: The Past, the Present, and the Future,” International Journal of Mechanical System Dynamics 2, no. 1 (2022): 3–26.

[34] X. Rui, X. Wang, Q. Zhou, and J. Zhang, “Transfer Matrix Method for Multibody Systems (Rui Method) and Its Applications,” Science China: Technological Sciences 62 (2019): 712–720.

[35] Y. Ding, X. Rui, H. Lu, Y. Chang, and Y. Chen, “Research on the Dynamic Characteristics of the Ultra-Precision Fly Cutting Machine Tool and Its Influence on the Mid-Frequency Waviness of the Surface,” Journal of Advanced Manufacturing Technology 106 (2020): 441–454.

[36] H. Lu, Y. Ding, Y. Chang, G. Chen, and X. Rui, “Dynamics Modelling and Simulating of Ultra-Precision Fly-Cutting Machine Tool,” International Journal of Precision Engineering and Manufacturing 21 (2020): 189–202.

[37] Z. Xu, T. Zhu, F. L. Luo, et al., “A Review: Insight Into Smart and Sustainable Ultra-Precision Machining Augmented by Intelligent IoT,” Journal of Manufacturing Systems 74 (2024): 233–251.

[38] X. Rui, G. Wang, and J. Zhang, Transfer Matrix Method for Multibody Systems: Theory and Applications (John Wiley & Sons, 2018).

[39] H. Lu, X. Rui, and X. Zhang, “Transfer Matrix Method for Linear Vibration Analysis of Flexible Multibody Systems,” Journal of Sound and Vibration 549 (2023): 117565.

[40] M. Kumar, A. M. Sidpara, and V. Racherla, “Finishing of OFHC Copper Using Fluid Filled Open-Cell Porous Flexible Abrasive Impregnated Tools,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 237, no. 6–7 (2023): 1086–1099.

[41] D. A. Khan and S. Jha, “Synthesis of Polishing Fluid and Novel Approach for Nanofinishing of Copper Using Ball-End Magnetorheological Finishing Process,” Materials and Manufacturing Processes 33, no. 11 (2018): 1150–1159.

[42] J. Kennedy and R. Eberhart, Particle Swarm Optimization. (IEEE, 1995), 1942–1948.

[43] D. Wang, D. Tan, and L. Liu, “Particle Swarm Optimization Algorithm: An Overview,” Soft Computing 22, no. 2 (2018): 387–408.

[44] S. Bharathi Raja and N. Baskar, “Particle Swarm Optimization Technique for Determining Optimal Machining Parameters of Different Work Piece Materials in Turning Operation,” International Journal of Advanced Manufacturing Technology 54 (2011): 445–463.

[45] D. Wang, D. Tan, and L. Liu, “Particle Swarm Optimization Algorithm: An Overview,” Soft Computing 22, no. 2 (2017): 387–408, https://doi.org/10.1007/s00500-016-2474-6.

[46] Y. Ding, X. Rui, Y. Chen, et al., “Modelling and Simulation of the 3D Surface Topography in Ultra-Precision Flycutting Machining,” IET Conference Proceedings 2022 (2022): 340–345.

RIGHTS & PERMISSIONS

2025 The Author(s). International Journal of Mechanical System Dynamics published by John Wiley & Sons Australia, Ltd on behalf of Nanjing University of Science and Technology.