Revealing the crack formation mechanism induced by intermetallic compounds in thick plate Al/Mg friction stir welded joints

Abstract

The mechanism of intermetallic compounds (IMCs) along the thickness direction on crack formation in thick plate Al/Mg friction stir welded (FSW) joints remains unresolved. This study investigates the effects of strain gradient, mismatch, and fracture toughness on crack formation. The results indicate that the cracks are exclusively formed in the upper of the stir zone and at the Al/Al₃Mg₂ interface. Crack formation in the upper of the stir zone is associated with the eutectic reaction (Al + Al₃Mg₂ ↔ Liquid). The Al/Al₃Mg₂ interface exhibits the highest lattice mismatch (δ = 2.27%) and misorientation gradient (0.7°), which corresponds to the preferential crack initiation site. In addition, nanoindentation tests confirm that the Al₁₂Mg₁₇ phase (0.41 MPa·m^1/2) possesses higher fracture toughness than the Al₃Mg₂ phase (0.28 MPa·m^1/2). Therefore, controlling the thickness of the Al₃Mg₂ phase is essential for suppressing crack formation. These findings provide a theoretical basis for crack suppression in thick Al/Mg FSW joints and are valuable for further improving joint quality.

Keywords

thick plate aluminum/magnesium joint / friction stir welding / crack / intermetallic compounds

References

[1] Fu XS, Chen K, Zhang QS, et al.Simultaneous improvement in strength and ductility of friction stir welded Mg/Al joints by reducing micro-intermixing. J. Mater. Res. Technol., 2024, 31: 1379.

[2] Li QB, Yang SL, Hu BG, Xue SQ. Laser welding of aluminum/steel dissimilar metals and control of intermetallic compounds: A review. Int. J. Adv. Manuf. Technol., 2025, 137(9):4283.

[3] Y. Zheng, G.C. Ren, and L.Y. Li, Improved mechanical and corrosion properties of friction stir welded Al/Mg dissimilar lap joints by Zr interlayer addition, Mater. Lett., 348(2023), art. No. 134710.

[4] Kostka A, Coelho RS, dos Santos J, Pyzalla AR. Microstructure of friction stir welding of aluminium alloy to magnesium alloy. Scripta Mater., 2009, 60(11):953.

[5] J. Yang, J.P. Oliveira, Y.L. Li, et al., Laser techniques for dissimilar joining of aluminum alloys to steels: A critical review, J. Mater. Process. Technol., 301(2022), art. No. 117443.

[6] Gaurav S, Mishra RS, Zunaid M. A critical review on mechanical and microstructural properties of dissimilar aluminum (Al)–magnesium (Mg) alloys. J. Adhes. Sci. Technol., 2023, 37(7):1117.

[7] Zhao JJ, Wu CS, Su H. Acoustic effect on the tensile properties and metallurgical structures of dissimilar friction stir welding joints of Al/Mg alloys. J. Manuf. Process., 2021, 65: 328.

[8] S.Y. Fan, Z. Zhang, Z.H. Li, et al., Eliminating overheating in friction stir welded high Zn-containing Al–Zn–Mg–Cu alloy thick plates by a super low shoulder rotation rate, Mater. Sci. Eng. A, 950(2026), art. No. 149553.

[9] Zettler R, da Silva AAM, Rodrigues S, Blanco A, dos Santos JF. Dissimilar Al to Mg alloy friction stir welds. Adv. Eng. Mater., 2006, 8(5):415.

[10] Kwon YJ, Shigematsu I, Saito N. Dissimilar friction stir welding between magnesium and aluminum alloys. Mater. Lett., 2008, 62(23):3827.

[11] Y. Xu, L.M. Ke, Y.Q. Mao, and P.L. Niu, Interfacial microstructure evolution of thick plate Al/Mg FSW: Effect of pin size, Mater. Charact., 174(2021), art. No. 111022.

[12] T.F. Huang, Z.Y. Zhang, J.L. Liu, et al., Interface Fonnation of medium-thick AA6061 A1/AZ₃₁B Mg dissimilar submerged friction stir welding joints, Materials, 15(2022), No. 16, art. No. 5520.

[13] Shi H, Chen K, Liang ZY, et al.Intermetallic compounds in the banded structure and their effect on mechanical properties of Al/Mg dissimilar friction stir welding joints. J. Mater. Sci. Technol., 2017, 33(4):359.

[14] Yang Y, Shen Z, Zhou P, et al.Interfacial microstructure and mechanical performance of oscillating refill friction stir spot welded Al/Mg dissimilar welds. J. Manuf. Process., 2026, 158: 251.

[15] McLean AA, Powell GLF, Brown IH, Linton VM. Friction stir welding of magnesium alloy AZ31B to aluminium alloy 5083. Sci. Technol. Weld. Join., 2003, 8(6):462.

[16] Khaliq UA, Muhamad MR, Yusof F, et al.Morphological, chemical, and crystallographic aspects of interface evolution in Al/Mg dissimilar friction stir welds. J. Mater. Res. Technol., 2025, 36: 6937.

[17] Y. Xu, H. Nie, S.J. Chen, L.M. Ke, Q. Liu, and C. Xia, Enhancing metallurgical bonding of thick plate friction stir welded Al/Mg joints by changing the friction interface, Mater. Charact., 209(2024), art. No. 113724.

[18] Zhang TH, Feng YH, Yang R, Jiang P. A method to determine fracture toughness using cube-corner indentation. Scripta Mater., 2010, 62(4):199.

[19] Venkateswaran P, Xu ZH, Li XD, Reynolds AP. Determination of mechanical properties of Al–Mg alloys dissimilar friction stir welded interface by indentation methods. J. Mater. Sci., 2009, 44(15):4140.

[20] Du HY, Li YJ, Wang J. Microstructure characteristic of AZ31/7005 joints by GTAW with filler wire of Mg–Al alloy. Adv. Mater. Res., 2014, 1004–1005: 168.

[21] D’Antuono DS, Gaies J, Golumbfskie W, Taheri ML. Grain boundary misorientation dependence of ß phase precipitation in an Al–Mg alloy. Scripta Mater., 2014, 76: 81.

[22] Koju RK, Mishin Y. Atomistic study of grain-boundary segregation and grain-boundary diffusion in Al–Mg alloys. Acta Mater., 2020, 201: 596.

[23] J. Ehrich, A. Roos, B. Klusemann, and S. Hanke, Influence of Mg content in Al alloys on processing characteristics and dynamically recrystallized microstructure of friction surfacing deposits, Mater. Sci. Eng. A, 819(2021), art. No. 141407.

[24] C. Wang, L.J. Meng, X.G. Ma, Z.Y. Jiang, and J.W. Zhao, Unveiling the interface fracture mechanism dominated by intermetallic compounds during tensile deformation of copper/aluminum composite thin strips, Mater. Des., 256(2025), art. No. 114264.

[25] Shen ZK, Ding YQ, Gerlich AP. Advances in friction stir spot welding. Crit. Rev. Solid State Mater. Sci., 2020, 45(6):457.

[26] Shen Z, Li WY, Ding Y, et al.Material flow during refill friction stir spot welded dissimilar Al alloys using a grooved tool. J. Mamf. Process., 2020, 49: 260.

[27] Y. Xu, L.M. Ke, Y.Q. Mao, Q. Liu, J.L. Xie, and H.R. Zeng, Formation investigation of intermetallic compounds of thick plate Al/Mg alloys joint by friction stir welding, Materials, 12(2019), No. 17, art. No. 2661.

[28] Panteli A, Robson JD, Brough I, Prangnell PB. The effect of high strain rate deformation on intermetallic reaction during ultrasonic welding aluminium to magnesium. Mater. Sci. Eng. A, 2012, 556: 31.

[29] Dietrich D, Nickel D, Krause M, Lampke T, Coleman MP, Randle V. Formation of intermetallic phases in diffusion-welded joints of aluminium and magnesium alloys. J. Mater. Sci., 2011, 46(2):357.

[30] Baghdadi AH, Sajuri Z, Selamat NTM, Omar MZ, Miyashita Y, Kokabi AH. Effect of intermetallic compounds on the fracture behavior of dissimilar friction stir welding joints of Mg and Al alloys. Int. J. Miner. Metall. Mater., 2019, 26(10):1285.

[31] Xiao L, Wang N. Growth behavior of intermetallic compounds during reactive diffusion between aluminum alloy 1060 and magnesium at 573–673K. J. Nucl. Mater., 2015, 456: 389.

[32] Liu XT, Cui JZ, Guo YH, Wu XM, Zhang J. Phase formation and growth in Al-Mg couple with an electromagnetic field. Mater. Lett., 2004, 58(9):1520.

[33] Xu Y, Ke LM, Mao YQ, Sun JF, Duan YX, Yu LM. An innovative joint interface design for reducing intermetallic compounds and improving joint strength of thick plate friction stir welded Al/Mg joints. J. Magnesium Alloys, 2023, 11(9):3151.

[34] Mola R, Mroz S, Szota P. Effects of the process parameters on the formability of the intermetallic zone in two-layer Mg/Al materials. Arch. Civ. Mech. Eng., 2018, 18(4):1401.

[35] Chang CI, Lee CJ, Huang JC. Relationship between grain size and Zener-Holloman parameter during friction stir processing in AZ31 Mg alloys. Scripta Mater., 2004, 51(6):509.

[36] Hoyos E, Montoya Y, Fernández R, Doncel GG. Approach to plastic deformation and strain rate in FSW process. Weld. World, 2021, 65(8):1519.

[37] Haddadi F. Rapid intermetallic growth under high strain rate deformation during high power ultrasonic spot welding of aluminium to steel. Mater. Des., 2015, 66: 459.

[38] Tang JW, Chen L, Zhao GQ, Zhang CS, Yu JQ. Study on Al/Mg/Al sheet fabricated by combination of porthole die co-extrusion and subsequent hot rolling. J. Alloy. Compd., 2019, 784: 727.

[39] Yang CL, Wu CS, Zhao JJ. Numerical prediction of intermetallic compounds thickness in friction stir welding of dissimilaraluminum/magnesium alloys. Acta Metall. Sin., 2021, 34(10):1375.

[40] J.D. Pribe, T. Siegmund, and J.J. Kruzic, The roles of yield strength mismatch, interface strength, and plastic strain gradients in fatigue crack growth across interfaces, Eng. Fract. Mech., 235(2020), art. No. 107072.

[41] Long LP, Liu WS, Ma YZ, Wu L, Tang SW. Evolution of voids in Mg/Al diffusion bonding process. High Temp. Mater. Process., 2017, 36(10):985.

[42] Bhattacharyya A, Maurice D. On the evolution of stresses due to lattice misfit at a Ni-superalloy and YSZ interface. Surf. Interfaces, 2018, 12: 86.

[43] H. Kim, M. Grandhi, Z.C. Liu, I.Z. Era, and H.C. Zhang, Interface bonding behavior and failure mechanism of joining Tribaloy T-800/AISI 4140 via laser engineered net shaping, Opt. Laser Technol., 156(2022), art. No. 108620.

[44] Nie HH, Liang W, Chen HS, et al.A coupled EBSD/TEM study on the interfacial structure of Al/Mg/Al laminates. J. Alloy. Compd., 2019, 781: 696.

Rights & permissions

University of Science and Technology Beijing