Analysis of loading characteristics of windshield wiper structure on high-speed train

Abstract

This paper studies the structural response of high-speed train wipers under the combined action of complex flow fields and scraping actions. The stress concentration areas are determined through simulation analysis, and the stress and aerodynamic load measurement points are reasonably arranged accordingly. The actual measurement is carried out in combination with the operating conditions of the existing lines. The stress variations and spectral characteristics of the train under different speed levels (80 , 160 , 180 , 200 km/h), tunnel entry and exit, and scraper action conditions were compared and analyzed. The stress amplification factors under tunnel intersection and scraper action were obtained, providing boundary conditions for the design of wipers for high-speed s. The research results show that the maximum stress of the wiper structure obtained through simulation calculation is concentrated at the connection of the wiper arm. Structural stress increases with the rise of speed grade. The stress increases by 1.11 times when the tunnel meets. When the scraper operates, the stress on the scraper arm increases by 4.1-7.6 times. Due to the broadband excitation effect of the aerodynamic load, the spectral energy of the structure is relatively high at the natural frequency, which excites the natural mode of the wiper.

Keywords

High-speed train / Wiper / Load characteristic / Strength / Natural frequency

References

[1] S. Lesterlin, F. Surdel, An accelerated test method for automotive wiper systems, SAE Technical Papers, SAE 2014 World Congress, 2014, pp. 11-17.

[2] Y.R. Chen, Y.G. Xiao, Aerodynamic performance calculation of high-speed trains, Roll. Stock 1 (47) (2009) 2-4.

[3] L.F. Chung, H.K. Versteeg, An Introduction to Computational Fluid Dynamics. The Finite Volume Method, Wiley, New York, 2017, pp. 212-215.

[4] J. Zhan, Experimental study on wind tunnel test of the shape of high-speed train locomotive head, J. Exp. Fluid Mech. 11 (2) (2007) 1-4.

[5] Y.H. Li, Research on aerodynamic characteristics of meeting oncoming vehicles, Jilin University, Changchun, 2006.

[6] Y.P. He, Z.P. Liu, G.Q. Peng, Dynamic research on the wiper of EMU based on rigid-flexible coupling and joint simulation, Mech. Eng. 6 (2020) 90-92.

[7] J. Fang, L.P. Lu, L. Shao, Large eddy simulation of compressible turbulent channel flow with spanwise wall oscillation, Sci. China-Phys. Mech. Astron. 52 (8) (2009) 1233-1243.

[8] S.V. Patanker, D.B. Spalding, A calculation processure for heat,mass and momentum transfer in three-dimensional parabolic flows, Int J. Heat. Mass Transf. 15 (1972) 1787-1806.

[9] G. Li, Y.G. Mei, Experimental research methods on aerodynamic models of high-speed trains entering and exiting tunnels abroad, Tunnel Constru. (S2) 2007 155-157.

[10] S. Maleki, D. Burton, M.C. Thompson, Flow structure between freight train containers with implications for aerodynamic drag, J. Wind Eng. Ind. Aerodyn. 188 (2019) 194-206.

[11] W. Yang, E. Deng, M. Lei, et al., Flow structure and aerodynamic behavior evolution during train entering tunnel with entrance in crosswind, J. Wind Eng. Ind. Aerodyn. 175 (2018) 229-243.

[12] M. Zhou, T. Liu, Y. Xia, et al., Comparative investigations of pressure waves induced by trains passing through a tunnel with different speed modes, J. Cent. South Univ. 29 (8) (2022) 2639-2653.

[13] Y.K. Liu, W.C. Yang, E. Deng, et al., Pressure amplification effect of initial compression waves in circumferential cracks of high-speed railway tunnel linings, Phys. Fluids 35 (6) (2023) 066119.

[14] J. Du, Q. Fang, J. Wang, et al., Influences of high-speed train speed on tunnel aerodynamic pressures, Appl. Sci. 12 (1) (2021) 303.

[15] Y.B. Lu, X.M. Wu, T.T. Wang, et al., Study on the adaptive relationship between train nose lengths and variable-section tunnel parameters: aiming at mitigating micro-pressure waves, Phys. Fluids 36 (5) (2024) 056112.