Topology optimization of a ratchet compensation structure subject to periodic constraints

Abstract

The railway pantograph-catenary system employs a ratchet compensation device to sustain the tension of the contact wire. However, the excessive weight associated with the ratchet structure adversely affects the performance of the compensation device. An optimization design aimed at lightweight optimization of the ratchet wheel structure can enhance the system’s agility, improve material utilization, and reduce costs. This study uses a finite element model to establish an equivalent load model for the ratchet under service conditions and analyzes its load-bearing state. An optimization model was created and solved using ANSYS Workbench. The topological optimization configurations were compared under unconstrained conditions and four different periodic constraint scenarios. Following this, the structure was redesigned based on the topological optimization results, and a simulation analysis was conducted to compare the reconstructed model with the original model. The comparison results indicate that the masses of all four optimized models have been reduced by more than 10 %. Additionally, under conditions of a fully wound compensation rope, the maximum stress has decreased by over 20 %, leading to a more uniform stress distribution and improved overall performance. The topology optimization and redesign method based on periodic constraints offers a viable engineering solution for the lightweight design of the ratchet structure.

Keywords

Topology optimization / SIMP density-based method / Ratchet compensation device / ANSYS Workbench

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this study.

Acknowledgements

This work was supported by the National Natural Science Foundation of China (Grant No. 52075033) and Research and Development Plan of REG (Grant No. 2023-20)

References

[1] L. Liu, Types and application of OCS compensation device, Electric Railway, 2004, pp. 23-26.

[2] O. Sigmund, N. Aage, E. Andreassen, On the (non-) optimality of Michell structures, Struct. Multidiscip. Optim. 54 (2016) 361-373.

[3] K.T. Cheng, N. Olhoff, An investigation concerning optimal design of solid elastic plates, Int. J. Solids Struct. 17 (3) (1981) 305-323.

[4] C. Keno-Tung, N. Olhoff, Regularized formulation for optimal design of axisymmetric plates, Int. J. Solids Struct. 18 (2) (1982) 153-169.

[5] M.P. Bendsøe, N. Kikuchi, Generating optimal topologies in structural design using a homogenization method, Comput. Methods Appl. Mech. Eng. 71 (2) (1988) 197-224.

[6] G. Costa, M. Montemurro, J. Pailhès, Minimum length scale control in a NURBS- based SIMP method, Comput. Appl. Mech. Eng. 354 (2019) 963-989.

[7] M.Y. Wang, X. Wang, D. Guo, A level set method for structural topology optimization, Comput. Methods Appl. Mech. Eng. 192 (1-2) (2003) 227-246.

[8] Y.M. Xie, G.P. Steven, A simple evolutionary procedure for structural optimization, Comput. Struct. 49 (5) (1993) 885-896.

[9] M.P. Bendsøe, N. Kikuchi, Generating optimal topologies in structural design using a homogenization method, Comput. Methods Appl. Mech. Eng. 71 (2) (1988) 197-224.

[10] H.Y. Xu, L.W. Guan, L.P. Wang, et al., Topology optimization for the arm of flight simulator under inertial loads, J. Mech. Eng. 50 (9) (2014) 14-23.

[11] V.B. Dinh, N.L. Chau, N.T.P. Le, et al., Topology-based geometry optimization for a new compliant mechanism using improved adaptive neuro-fuzzy inference system and neural network algorithm, Eng. Comput. (2021) 1-30.

[12] E. Biyikli, A.C. To, Proportional topology optimization: A new non-sensitivity method for solving stress constrainedand minimum compliance problems and its implementation in MATLAB, PloS One 10 (12) (2015) e0145041.

[13] Y.C. Bai, K. Liu, C. Li, et al., Eigenfrequency topology optimization of 3D shell-infill structures based on large-scale parallel computing, J. Mech. Eng. 60 (11) (2024) 32-40.

[14] J.Q. Zhan, T.S. Liu, M. Liu, et al., Topological design of compliant mechanisms considering fatigue constraints, J. Mech. Eng. 57 (3) (2021) 59-68.

[15] L. Meng, M.Z. Zhong, W.B. Li, et al., Topology optimization design of aero-engine external system brackets for additive manufacturing, J. Mech. Eng. 33 (23) (2022) 2822-2832.

[16] Y.J. Liu, Q. Hu, X.M. Zhao, et al., Research on topology optimization and additive manufacturing of automotive engine connection brackets, China Mech. Eng. 34 (18) (2023) 2238-2247.

[17] X.F. Zheng, Z.H. Huang, X.L. Ma, et al., Structure optimization and analysis of pole- climbing robot based on SIMP method, Chin. J. Eng. Des. 30 (3) (2023) 342-352.

[18] D. Chu, W. Bai, Y. He, et al., Research on lightweight technology of new carbon fiber wheel hub structure, IOP Conference Series:Earth and Environmental Science. IOP Publishing, 2021, 632(5) 052071.

[19] Z.S. Lu, Y.J. Chen, Y.L. Wang, et al., Optimization design of automobile wheel hub based on ANSYS, J. Harbin Univ. Commer. (Nat. Sci. Ed.) 38 (3) (2022) 318-324.

[20] G.Y. Yang, Lightweight design of automobile wheel hub based on concept design, Mech. Electr. Eng. Technol. 52 (6) (2023) 257-262.

[21] P.F. Xu, S.Y. Duan, F. Wang, Reverse modeling and topological optimization for lightweight design of automobilewheel hubs with hollow ribs, Int. J. Comput. Methods 17 (9) (2020) 1950064.

[22] T. Shinde, A. Jomde, S. Shamkuwar, et al.,Fatigue analysis of alloy wheel using cornering fatigue test and its weight optimization, Mater. Today. Proc. 62 (2022) 1470-1474.

[23] M.M. Wang, Structural design and optimization of aluminum alloy automobile wheel, Jilin University, 2011.

[24] Z.H. Liu,Research on new design method of automobile wheel for 3D printing technology, Harbin Institute of Technology, Heilongjiang, 2021.

[25] H.M. Dai, Lightweight design of gear based on multi-objective topology optimization technology, Mach. Des. Manuf. (5) (2020) 116-119.

[26] Y.W. Xue, Lightweight design and dynamic analysis of aviation gear, Taiyuan University of Technology, Shanxi, 2018.

[27] Q.Q. Jiang, Dynamic force distribution and design optimization for multi-layer winding drum, Shanghai Jiao Tong University, Shanghai, 2016.

[28] X.H. Dong, X.H. Ding, Topology optimum design method for periodic stiffener structures based on adaptive growth method, China Mech. Eng. 29 (17) (2018) 2045-2051.

[29] L. Wang, Y.W. Zhao, S.D. Ren, et al., Conceptual design generation of automotive wheel hubs based on reinforcement learning and topology optimization, High. Technol. Lett. 34 (9) (2024) 1003-1012.

[30] G.J. Shang, H. Chen, R.M. Chen, et al., Static finite element simulation analysis of ratchet compensation device of catenary, Mech. Electr. Eng. Technol. 51 (12) (2022) 175-182.

[31] J.J. Xie, Y. Wang, J.G. Zhang, Online performance monitoring of railway catenary tension wheel equipment, Chin. J. Sci. Instrum. 36 (2) (2015) 466-472.

[32] Q. Su, H.B. Wang, Analysis and optimization of friction drum for photovoltaic module installation equipment, Mach. Des. Res. 39 (4) (2023) 252-256.

[33] Z.P. Guo, Topology optimization of tensile and compressive anisotropic materials based on SIMP-MMC, Guangzhou University, Guangdong, 2023.