Stability analysis and strength optimization of cemented tailings backfill in high-temperature mining

Chao Zhang , Jinping Guo , Weidong Song , Yuye Tan , Abbas Taheri , Xiaolin Wang

Green and Smart Mining Engineering ›› 2025, Vol. 2 ›› Issue (1) : 84 -96.

PDF (15124KB)
Green and Smart Mining Engineering ›› 2025, Vol. 2 ›› Issue (1) :84 -96. DOI: 10.1016/j.gsme.2025.02.002
research-article
Stability analysis and strength optimization of cemented tailings backfill in high-temperature mining
Author information +
History +
PDF (15124KB)

Abstract

To investigate changes in stope stability and cemented tailings backfill (CTB) strength during deep metal mine mining using the filling method in a high-temperature environment, this study analyzed the temperature and mechanical characteristics of the stope via numerical simulations. The optimal CTB mix ratio at different mining depths was determined, and the corresponding safety control measures for deep metal mine filling mining were proposed. Results show that the coupled effect of the temperature field and hydration heat release during deep filling mining complicate the stope environment. Owing to the difficulty in heat dissipation in the middle of the bulk CTB in the stope, the internal temperature of the CTB increases significantly within a short duration. Moreover, the rapid heat conduction around the CTB caused by its direct contact with the surrounding rock causes the temperature field to distribute from the center to the periphery. Throughout the sublevel mining process, the CTB temperature field exhibits the following change pattern: stable → rapidly increasing → slowly decreasing → rapidly increasing → slowly decreasing to stable → slowly increasing → slowly decreasing to stable. A comparison of test results obtained from pillar mining simulations show that the coupled temperature–stress model exhibits greater stability and safety than the single mechanical model. The CTB provides better support under the coupling effect, thus enhancing its mechanical properties under high temperature. A safety factor is introduced for the quantitative analysis of slope stability. The optimal CTB mix ratio at different mining depths is determined via safety factor iteration and economic comparison analysis. Subsequently, a reasonable temperature control scheme was designed, which offers insights into high-efficiency mining while ensuring CTB stability under high temperature.

Keywords

Temperature effect / Cemented tailings backfill / Strength optimization / Numerical simulation

Cite this article

Download citation ▾
Chao Zhang, Jinping Guo, Weidong Song, Yuye Tan, Abbas Taheri, Xiaolin Wang. Stability analysis and strength optimization of cemented tailings backfill in high-temperature mining. Green and Smart Mining Engineering, 2025, 2 (1) : 84-96 DOI:10.1016/j.gsme.2025.02.002

登录浏览全文

4963

注册一个新账户 忘记密码

References

[1]

N.M. Nguyen, D.T. Pham, Tendencies of mining technology development in relation to deep mines, Gorn. Nauk. Tehnol. 4 (1) (2019) 16-22.

[2]

P. Li, M.F. Cai, Challenges and new insights for exploitation of deep underground metal mineral resources, Trans. Nonferrous Met. Soc. China 31 (11) (2021) 3478-3505.

[3]

Z.Q. He, H.P. Xie, M.Z. Gao, L. Chen, B. Yu, Y.Q. Hu, J.P. Yang, Design and verification of a deep rock corer with retaining the in situ temperature , Adv. Civ. Eng. 2020 (1) (2020) 8894286.

[4]

A.X. Wu, Y. Wang, Z.E. Ruan, B.L. Xiao, J.D. Wang, L.Q. Wang, Key theory and technology of cemented paste backfill for green mining of metal mines, Green Smart Min. Eng. 1 (1) (2024) 27-39.

[5]

Y.H. Cheng, H. Shen, J.F. Zhang, Understanding the effect of high-volume fly ash on micro-structure and mechanical properties of cemented coal gangue paste backfill, Constr. Build. Mater. 378 (2023) 131202.

[6]

A. Ghirian, M. Fall, Coupled behavior of cemented paste backfill at early ages, Geotech. Geol. Eng. 33 (5) (2015) 1141-1166.

[7]

N. Sivakugan, R. Veenstra, N. Naguleswaran, Underground mine backfilling in Australia using paste fills and hydraulic fills, Int. J. Geosynth. Ground Eng. 1 (2) (2015) 18.

[8]

J. Tao, X.G. Yang, P.P. Ding, X.L. Li, J.W. Zhou, G.D. Lu, A fully coupled thermo-hydro-mechanical-chemical model for cemented backfill application in geothermal conditions, Eng. Geol. 302 (2022) 106643.

[9]

S.H. Yin, Y.J. Shao, A.X. Wu, Z.Y. Wang, L.H. Yang, Assessment of expansion and strength properties of sulfidic cemented paste backfill cored from deep underground stopes, Constr. Build. Mater. 230 (2020) 116983.

[10]

E. Yilmaz, T. Belem, M. Benzaazoua, Specimen size effect on strength behavior of cemented paste backfills subjected to different placement conditions, Eng. Geol. 185 (2015) 52-62.

[11]

W. Sun, D. Wu, E. Yilmaz, G.D. Yang, J. Liu, Delving into the role of microwave curing on the strength and cement hydration features of cemented tailings backfill, Green Smart Min. Eng. 1 (3) (2024) 289-298.

[12]

Q.S. Chen, Q.L. Zhang, A. Fourie, X. Chen, C.C. Qi, Experimental investigation on the strength characteristics of cement paste backfill in a similar stope model and its mechanism, Constr. Build. Mater. 154 (2017) 34-43.

[13]

X. Zhao, A. Fourie, C.C. Qi, An analytical solution for evaluating the safety of an exposed face in a paste backfill stope incorporating the arching phenomenon, Int. J. Miner. Metall. Mater. 26 (10) (2019) 1206-1216.

[14]

F.F. Jiang, H. Zhou, J. Sheng, Y.Y. Kou, X.D. Li, Effects of temperature and age on physico-mechanical properties of cemented gravel sand backfills, J. Cent. South Univ. 27 (10) (2020) 2999-3012.

[15]

Z. Aldhafeeri, M. Fall, M. Pokharel, Z. Pouramini, Temperature dependence of the reactivity of cemented paste backfill, Appl. Geochem. 72 (2016) 10-19.

[16]

Y. Zhao, A. Taheri, M. Karakus, A. Deng, L.J. Guo, The effect of curing under applied stress on the mechanical performance of cement paste backfill, Minerals 11 (10) (2021) 1107.

[17]

D.Y. Wei, C.F. Du, Y.F. Lin, B.M. Chang, Impact factors of hydration heat of cemented tailings backfill based on multi-index optimization, Case Stud. Therm. Eng. 18 (2020) 100601.

[18]

O. Nasir, M. Fall, Coupling binder hydration, temperature and compressive strength development of underground cemented paste backfill at early ages, Tunn. Undergr. Space Technol. 25 (1) (2010) 9-20.

[19]

K. Zhao, M. Huang, Y. Zhou, Y.J. Yan, W.L. Wan, F.J. Ning, Z.W. He, J.Q. Wang, Synergistic deformation in a combination of cemented paste backfill and rocks, Constr. Build. Mater. 317 (2022) 125943.

[20]

Z.W. He, K. Zhao, Y.J. Yan, F.J. Ning, Y. Zhou, Y.F. Song, Mechanical response and acoustic emission characteristics of cement paste backfill and rock combination, Constr. Build. Mater. 288 (2021) 123119.

[21]

Y. Zhao, A. Taheri, A. Soltani, M. Karakus, A. Deng, Strength development and strain localization behavior of cemented paste backfills using Portland cement and fly ash, Materials 12 (20) (2019) 3282.

[22]

W. Ting, A. Hasan, Stress behaviour of cemented paste backfill within temperature controlled stope model, Int. J. Min. Reclam. Environ. 37 (10) (2023) 996-1015.

[23]

M.L. Walske, H. McWilliam, J. Doherty, A. Fourie, Influence of curing temperature and stress conditions on mechanical properties of cementing paste backfill, Can. Geotech. J. 53 (1) (2016) 148-161.

[24]

Q. Zhang, J.X. Zhang, X.L. Han, F. Ju, Y. Tai, M. Li, Theoretical research on mass ratio in solid backfill coal mining, Environ. Earth Sci. 75 (7) (2016) 586.

[25]

M. Wang, Y. Wang, L. Liu, M.L. Geng, X.L. Wang, L.Y. Qiu, Experimental and numerical research of backfill cooling based on similarity theory, J. Build. Eng. 70 (2023) 106380.

[26]

R.F. Wang, F.T. Zeng, L. Li, Stability analyses of side-exposed backfill considering mine depth and extraction of adjacent stope, Int. J. Rock. Mech. Min. Sci. 142 (2021) 104735.

[27]

G.O. Oniyide, M.A. Idris, Numerical modelling of the effect of temperature variation on stope stability in Bushveld Igneous Complex, Min. Miner. Depos. 13 (2) (2019) 121-131.

[28]

N. El Mkadmi, M. Aubertin, L. Li, Effect of drainage and sequential filling on the behavior of backfill in mine stopes, Can. Geotech. J. 51 (1) (2014) 1-15.

[29]

W.H. Xia, Y. Li, W.D. Song, J.X. Fu, C. Zhang, L. Yu, Stability analysis of secondary mining of submarine mine under the clamping control of fault and fracture zone, Min. Metall. Explor. 41 (2) (2024) 909-924.

[30]

B.Q. Yan, S.J. Che, D.D. Tannant, F.H. Ren, P.T. Wang, Application of double-yield model in numerical simulation of stability of mining filling body, Arab. J. Geosci. 12 (16) (2019) 515.

[31]

O. Çetindemir, Nonlinear constitutive soil models for the soil-structure interaction modeling issues with emphasis on shallow tunnels: a review, Arab. J. Sci. Eng. 48 (10) (2023) 12657-12691.

[32]

V.M. Nguyen, Q.P. Nguyen, V.D. Bui, Study of the heat generation due to the hydration of Portland cement using FLAC3D , in: The 1ST International Conference on Innovations for Computing, Engineering and Materials, 2021: Icem, AIP Publishing, Ho Chi Minh City, Vietnam, 2021, 060001.

[33]

H. Konietzky, L. Te Kamp, M. Kreienmeyer, N. Müller-Hoeppe, A thermo-mechanical constitutive law for modeling the hydration of concrete and backfill and its practical application using the parallel version of FLAC3D, in: D. Billaux, C. Detournay, R. Hart, X. Rachez (Eds.), FLAC and Numerical Modeling in Geomechanics-2001, CRC Press, London, 2020, pp. 15-20.

[34]

C. Zhang, W.D. Song, A. Taheri, J.X. Fu, T.Y. Zhao, Y.Y. Tan, Hydration mechanism and mechanical-thermal correlation of cemented paste backfill under different curing temperatures, J. Build. Eng. 85 (2024) 108691.

[35]

C. Zhang, A. Taheri, C.F. Du, W.H. Xia, Y.Y. Tan, Mechanical characteristics and macro-microscopic response mechanisms of cemented paste backfill under different curing temperatures, Minerals 14 (4) (2024) 433.

[36]

B.Y. Hu, X.M. Wang, S. Li, J.W. Zhao, N.M. Eugénie, Stability analysis and confidence level evaluation of backfill mining under high and steep rock slopes, Adv. Civ. Eng. 2018 (1) (2018) 3029796.

[37]

K.Z. Xia, C.X. Chen, X.T. Liu, X.M. Liu, J.H. Yuan, S. Dang, Assessing the stability of high-level pillars in deeply-buried metal mines stabilized using cemented backfill, Int. J. Rock Mech. Min. Sci. 170 (2023) 105489.

[38]

S. Cao, G.L. Xue, E. Yilmaz, Z.Y. Yin, F.D. Yang, Utilizing concrete pillars as an environmental mining practice in underground mines, J. Clean. Prod. 278 (2021) 123433.

[39]

M. Wang, L. Liu, X.Y. Zhang, L. Chen, S.Q. Wang, Y.H. Jia, Experimental and numerical investigations of heat transfer and phase change characteristics of cemented paste backfill with PCM, Appl. Therm. Eng. 150 (2019) 121-131.

[40]

L. Liu, C. Zhu, C.C. Qi, M. Wang, C. Huan, B. Zhang, K.I. Song, Effects of curing time and ice-to-water ratio on performance of cemented paste backfill containing ice slag, Constr. Build. Mater. 228 (2019) 116639.

[41]

C. Zhu, P. yang, L. Liu, Y.Y. Pu, C.C. Qi, Q.S. Chen, J. Chen, Effect of ice addition on the properties and microstructure of cemented paste backfill at early-age, J. Build. Eng. 71 (2023) 106439.

[42]

M. Wang, P. Liu, S.Y. Shang, Q. Chen, B. Zhang, L. Liu, Numerical and experimental studies on the cooling performance of backfill containing phase change materials, Build. Environ. 218 (2022) 109155.

[43]

L. Liu, Z.Y. Fang, M. Wang, C.C. Qi, Y.J. Zhao, C. Huan, Experimental and numerical study on rheological properties of ice-containing cement paste backfill slurry, Powder Technol. 370 (2020) 206-214.

PDF (15124KB)

0

Accesses

0

Citation

Detail

Sections
Recommended

/