Investigation of the partition failure process and energy evolution in coal-rock composite structure under free surface unloading

Abstract

Unloading failure of the coal-rock (CR) system is the key factor leading to rock burst disaster. Therefore, it is very important to explore the failure mechanism of the CR system by laboratory test. Initially, CR composite samples underwent laboratory tests with unloading pressure at various rates (0.03-0.12 ​MPa/s). However, due to the limitations of the available monitoring equipment, the recorded deformation data were restricted to the coal mass, which may lead to inaccurate conclusions as potential rock deformation was not captured. Subsequently, coal and rock mass deformations were separately monitored by simulating corresponding unloading pressure tests using PFC2D numerical software. Simulation results suggested that the peak of the AE event during the critical stage before sample failure could serve as an indicator of imminent sample destabilization. Post-failure observation revealed a higher degree of damage in the coal mass (35.02%) compared to the rock mass (12.17%), indicating that coal mass destabilization triggers destabilization in CR composite samples. Moreover, faster unloading rates corresponded to deeper damage in the coal mass. Additionally, macroscopic tensile and tensile-shear cracks were observed in the rock mass, while macroscopic shear cracks were present in the coal mass, providing insights into the unloading confining failure mode of CR samples. Finally, the study established a relationship between unloading rate and bursting liability by introducing the elastic energy density difference index. The research results can provide a theoretical basis for the prevention and control of rock burst disasters.

Keywords

Coal-rock composite / Coal and rock masses / Crack evolution / Energy evolution / Elastic energy density difference

CRediT authorship contribution statement

Wenkai Ru: Writing-original draft, Validation, Software, Methodology, Investigation. Shanchao Hu: Writing-review & editing, Project administration, Funding acquisition, Formal analysis, Data curation, Conceptualization. Qingheng Gu: Writing-review & editing. Qing Ma: Writing-review & editing.

Declaration of competing interests

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (No. 52274087) and the Natural Science Foundation of Shandong Province (No. ZR2023ME189).

References

[1] M. He, H. Xie, S. Peng, Y. Jiang, Study on rock mechanics in deep mining engineering, Chin. J. Rock Mech. Eng. 24 (16) ( 2005) 2803-2813.

[2] Y. Kang, X. Li, Y. Lu, C. Yang, Application of chaotic phase space reconstruction into nonlinear time series prediction in deep rock mass. 2008 Fifth International Conference on Fuzzy Systems and Knowledge Discovery, IEEE ASME Trans. Mechatron. 5 ( 2008) 593-597.

[3] M. Askaripour, A. Saeidi, A. Rouleau, P. Mercier-Langevin, Rockburst in underground excavations: a review of mechanism, classification, and prediction methods, Undergr. Space 7 (4) ( 2022) 577-607.

[4] X. Ou, L. Ouyang, X. Xu, L. Wang, Case study on floor heave failure of highway tunnels in gently inclined coal seam, Eng. Fail. Anal. 136 ( 2022) 106224.

[5] J. Wang, Q. Zhang, J. Zhang, H. Liu, G. Zhu, Y. Wang, Study on the controller factors associated with roof falling and ribs spalling in deep mine with great mining height and compound roof, Eng. Fail. Anal. 129 ( 2021) 105723.

[6] M. He, Rock mechanics and hazard control in deep mining engineering in China. Rock Mechanics in Underground Construction: (With CD-ROM), 2006, pp. 29-46.

[7] C. Li, Z. Tan, K. Deng, P. Li, Synergistic instability of coal pillar and roof system and filling method based on plate model, Int. J. Min. Sci. Technol. 23 (1) ( 2013) 145-149.

[8] I. Petukhov, A. Linkov, The theory of post-failure deformations and the problem of stability in rock mechanics, Int. J. Rock Mech. Min. Sci. Geomech. Abstracts 16 (2) ( 1979) 57-76. Pergamon.

[9] X. Deng, H. Hu, X. Gang, X. Li, F. Chen, Numerical simulation for burst failure of two-body rock structure, Journal of Mining and Safety Engineering 29 (6) ( 2012)833.

[10] G. Chen, Z. Qin, G. Zhang, T. Li, J. Li, Law of energy distribution before failure of a loaded coal-rock combined body, Rock Soil Mech. 41 (6) ( 2020) 1-13.

[11] L. Sacchi, A. Taliercio, A note on failure conditions for layered materials, Meccanica 22 (2) ( 1987) 97-102.

[12] Z. He, C. Lu, X. Zhang, Y. Guo, C. Wang, H. Zhang, B. Wang, Research on mechanisms and precursors of slip and fracture of coal-rock parting-coal structure, Rock Mech. Rock Eng. 55 (3) ( 2022) 1343-1359.

[13] Y. Liu, C. Lu, X. Zhang, Y. Guo, C. Song, C. Wang, Failure and instability characteristics of coal-rock parting-coal structures with rough discontinuities, Rock Mech. Rock Eng. ( 2022) 1-18.

[14] Z. Lu, W. Ju, F. Gao, K. Yi, Influence of loading rate on the failure characteristics of composite coal-rock samples under quasi-static loading conditions, Rock Mech. Rock Eng. 55 (2) ( 2022) 909-921.

[15] Z. Cheng, L. Li, Y. Zhang, Laboratory investigation of the mechanical properties of coal-rock combined body, Bull. Eng. Geol. Environ. 79 (4) ( 2020) 1947-1958.

[16] T. Wang, Z. Ma, Research on strain softening constitutive model of coal-rock combined body with damage threshold, Int. J. Damage Mech. 31 (1) ( 2022) 22-42.

[17] A. Cao, G. Jing, Y. Ding, S. Liu, Mining-induced static and dynamic loading rate effect on rock damage and acoustic emission characteristic under uniaxial compression, Saf. Sci. 116 ( 2019) 86-96.

[18] Q. Ma, Y. Tan, X. Liu, Z. Zhao, D. Fan, L. Purev, Experimental and numerical simulation of loading rate effects on failure and strain energy characteristics of coalrock composite samples, J. Cent. S. Univ. 28 (10) ( 2021) 3207-3222.

[19] L. Zhang, Comprehensive analysis of evolution characteristics of acoustic emission during deformation and failure of protruding coal body, J. China Coal Soc. 43 (B06) ( 2018) 130-139.

[20] X. Li, S. Chen, E. Wang, Z. Li, Rockburst mechanism in coal rock with structural surface and the microseismic (MS) and electromagnetic radiation (EMR) response, Eng. Fail. Anal. 124 ( 2021) 105396.

[21] Y. Chen, J. Zuo, D. Liu, Y. Li, Z. Wang, Experimental and numerical study of coalrock bi-material composite bodies under triaxial compression, International Journal of Coal Science & Technology 8 (5) ( 2021) 908-924.

[22] X. Bao, J. Guo, Y. Liu, G. Zhao, J. Cao, J. Wu, J. Zhao, Damage characteristics and laws of micro-crack of underwater electric pulse fracturing coal-rock mass, Theor. Appl. Fract. Mech. 111 ( 2021) 102853.

[23] Z. Yang, C. Liu, S. Tang, L. Dou, J. Cao, Rock burst mechanism analysis in an advanced segment of gob-side entry under different dip angles of the seam and prevention technology, Int. J. Min. Sci. Technol. 28 (6) ( 2018) 891-899.

[24] W. Shen, W. Yu, B. Pan, K. Li, Rock mechanical failure characteristics and energy evolution analysis of coal-rock composite with different dip angles, Arabian J. Geosci. 15 (1) ( 2022) 1-14.

[25] Z. Yang, C. Liu, S. Tang, L. Dou, J. Cao, Rock burst mechanism analysis in an advanced segment of gob-side entry under different dip angles of the seam and prevention technology, Int. J. Min. Sci. Technol. 28 (6) ( 2018) 891-899.

[26] Q. Ma, Y. Tan, X. Liu, Q. Gu, X. Li, Effect of coal thicknesses on energy evolution characteristics of roof rock-coal-floor rock sandwich composite structure and its damage constitutive model, Compos. B Eng. 198 ( 2020) 108086.

[27] T. Zhao, X. Gu, W. Guo, X. Gong, Y. Xiao, B. Kong, C. Zhang, Influence of rock strength on the mechanical behavior and P-velocity evolution of coal-rock composite sample. , J. Mater Res. Technol. 12 ( 2021) 1113-1124.

[28] C. Zhang, J. Pan, Y. Xia, G. Yang, Study on impact failure characteristics of combined coal and rock under true triaxial loading and unloading, Chin. J. Rock Mech. Eng. 39 (8) ( 2020) 1522-1533.

[29] X. Zhang, Q. Zhang, S. Wu, Acoustic emission characteristics of the rock-like material containing a single flaw under different compressive loading rates, Comput. Geotech. 83 ( 2017) 83-97.

[30] Z. Cheng, L. Li, Y. Zhang, Laboratory investigation of the mechanical properties of coal-rock combined body, Bull. Eng. Geol. Environ. 79 (4) ( 2020) 1947-1958.

[31] F. Gong, H. Ye, Y. Luo, Rate effect on the burst tendency of coal-rock combined body under low loading rate range, J. China Coal Soc. 42 (11) ( 2017) 2852-2860.

[32] X. Li, H. Li, J. Li, X. Xia, Crack initiation and propagation simulation for polycrystalline-based brittle rock utilizing three-dimensional distinct element method. ISRM 2nd International Conference on Rock Dynamics, OnePetro, 2016.

[33] M. Zhai, L. Xue, F. Bu, B. Yang, H. Ding, Microcracking behaviors and acoustic emission characteristics of granite subjected to direct shear based on a novel grainbased model, Comput. Geotech. 151 ( 2022) 104955.

[34] J. Fu, K. Chen, W. Zhu, X. Zhang, X. Li, Progressive failure of new modeling material with a single internal crack under biaxial compression and the 3-D numerical simulation, Eng. Fract. Mech. 165 ( 2016) 140-152.

[35] B. He, X. Zhuang, Modeling hydraulic cracks and inclusion interaction using XFEM, Undergr. Space 3 (3) ( 2018) 218-228.

[36] E. Hoek, C. Martin, Fracture initiation and propagation in intact rock-a review, J. Rock Mech. Geotech. Eng. 6 (4) ( 2014) 287-300.

[37] S. Yang, Y. Huang, H. Jing, X. Liu, Discrete element modeling on fracture coalescence behavior of red sandstone containing two unparallel fissures under uniaxial compression, Eng. Geol. 178 ( 2014) 28-48.

[38] F. Xiong, X. Liu, X. Zhou, G. Lin, D. Liu, Y. Han, B. Xu, C. He, Z. Wang, Mechanical behaviors of sandstone containing intersecting fissures under uniaxial compression, J. Rock Mech. Geotech. Eng. 14 (2) ( 2022) 460-476.

[39] A. Ting, Z. Ru, J. Li, R. Li,Space-time evolution rules of acoustic emission location of unloaded coal sample at different loading rates, Int. J. Min. Sci. Technol. 22 (6) ( 2012) 847-854.

[40] X. Zhang, S. Peng, The relationship between the characteristics of isotropic compression and triaxial shear deformation and brittleness evolution of hard rock. Proceedings of the Chinese Mechanics Congress 2017 and the 60th Anniversary of the Chinese Mechanics Society (A), 2017, pp. 1641-1649.

[41] P. Ranjith, D. Jasinge, J. Song, S. Choi, A study of the effect of displacement rate and moisture content on the mechanical properties of concrete: use of acoustic emission, Mech. Mater. 40 (6) ( 2008) 453-469.

[42] J. Peng, M. Cai, G. Rong, C. Zhou, X. Zhao, Stresses for crack closure and its application to assessing stress-induced microcrack damage, Chin. J. Rock Mech. Eng. 34 (6) ( 2015) 1091-1100.

[43] H. Zhang, D. Elsworth, Z. Wan, Failure response of composite rock-coal samples, Geomechanics and Geophysics for Geo-Energy and Geo-Resources 4 (2) ( 2018) 175-192.

[44] J. Liu, N. Wu, G. Si, M. Zhao, Experimental study on mechanical properties and failure behavior of the pre-cracked coal-rock composite, Bull. Eng. Geol. Environ. 80 (3) ( 2021) 2307-2321.

[45] R. Cao, R. Yao, T. Hu, C. Wang, K. Li, J. Meng, Failure and mechanical behavior of transversely isotropic rock under compression-shear tests: laboratory testing and numerical simulation. , Eng. Fract. Mech. 241 ( 2021) 107389.

[46] Y. Huang, S. Yang, W. Tian, S. Wu, Experimental and DEM study on failure behavior and stress distribution of flawed sandstone samples under uniaxial compression, Theor. Appl.Fract. Mech. 118 ( 2022) 103266.

[47] L. Yang, F. Gao, X. Wang, Mechanical response and energy partition evolution of coal rock composites with different strength ratios, Chin. J. Rock Mech. Eng. 39 (S2) ( 2020) 3297-3305.

[48] G. Chen, Z. Qin, G. Zhang, T. Li, J. Li, Law of energy distribution before failure of a loaded coal-rock combined body, Rock Soil Mech. 41 (6) ( 2020) 1-13.

[49] J. Zuo, H. Song,Energy evolution law and differential energy instability model of coal-rock mass, J. China Coal Soc. 47 (8) ( 2022) 3037-3051.

[50] F. Gong, H. Ye, Y. Luo,Rate effect on the burst tendency of coal-rock combined body under low loading rate range, J. China Coal Soc. 42 (11) ( 2017) 2852-2860.

[51] GB/T 25217.3-2019, Methods for Determination, Monitoring, and Prevention of Rock Burst-Part 3: Classification of Bursting Liability and Determination of the Index of Coal-Rock Composite Samples.

[52] F. Gong, J. Yan, X. Li, S. Luo, A peak-strength strain energy storage index for rock burst proneness of rock materials, Int. J. Rock Mech. Min. Sci. 117 ( 2019) 76-89.