Development of similarity and normalization models for spray characteristics with the momentum equation as the theoretical basis

Meiqi Yu , Hongliang Luo , Weidi Huang , Pengbo Dong , Yu Jin , Keiya Nishida , Chang Zhai , Xiaoqing Tian

Green Energy and Resources ›› 2026, Vol. 4 ›› Issue (3) : 100189

PDF (7640KB)
Green Energy and Resources ›› 2026, Vol. 4 ›› Issue (3) :100189 DOI: 10.1016/j.gerr.2026.100189
Research Article
research-article
Development of similarity and normalization models for spray characteristics with the momentum equation as the theoretical basis
Author information +
History +
PDF (7640KB)

Abstract

Fuel atomization in diesel engines can be significantly improved by elevating the injection pressure and decreasing the nozzle orifice diameter. Addressing the limited research on mathematical modeling within the regime of 300-MPa-level injection and micro-holes, this paper presents a comprehensive study on the similarity and normalization of spray evolution for ultra-high-pressure micro-nozzle configurations. In the experiments, key parameters such as injection pressure difference, ambient density, and hole diameter were selected as the main variables. The spray development process was divided into two main stages, and the similarity criteria and normalization equations for spray characteristics were derived accordingly. Combined with the DBI (Diffused Back-Illumination) method and processing technology, experimental data were obtained to verify the reliability of the established models. The experimental results show that both the similarity conversion results and normalization results of the derived mathematical models exhibit good consistency with the experimental data. This study can provide theoretical support for the optimization and spray characteristic prediction of ultra-high pressure small high-speed diesel engines.

Keywords

0.07 mm hole diameter / 300 MPa injection pressure / Normalized mathematical model

Cite this article

Download citation ▾
Meiqi Yu, Hongliang Luo, Weidi Huang, Pengbo Dong, Yu Jin, Keiya Nishida, Chang Zhai, Xiaoqing Tian. Development of similarity and normalization models for spray characteristics with the momentum equation as the theoretical basis. Green Energy and Resources, 2026, 4 (3) : 100189 DOI:10.1016/j.gerr.2026.100189

登录浏览全文

4963

注册一个新账户 忘记密码

References

[1]

An, C., Liu, L., Luo, H., Xiong, Q., Zhou, B., Liu, Y., Li, X., Nishida, K., 2025. Experimental and modeling study of the ultra-high pressure spray dynamics in the near and far fields under high ambient density conditions. Energy, 138464. https://doi.org/10.1016/j.energy.2025.138464.

[2]

Arai, M., 2022. Interpretative review of diesel spray penetration normalized by length and time of breakup (similarity law of diesel spray and its application). Energies 15 (13), 4926. https://doi.org/10.3390/en15134926.

[3]

Arrégule, J., Pastor, J.V., Ruiz, S., 1999. The influence of injection parameters on diesel spray characteristics (No. 1999-01-0200). https://doi.org/10.4271/1999-01-0200.

[4]

Bergin, M., Reitz, R.D., Hessel, R.P., 2005. Soot and NOx emissions reduction in diesel engines via spin-spray combustion. In: ILASS American, 18th Annual Conference on Liquid Atomization Spray Systems, Irvine, CA.

[5]

Chen, P.C., Wang, W.C., Roberts, W.L., Fang, T., 2013. Spray and atomization of diesel fuel and its alternatives from a single-hole injector using a common rail fuel injection system. Fuel 103, 850-861. https://doi.org/10.1016/j.fuel.2012.08.013.

[6]

Dent, J.C., 1971. A basis for the comparison of various experimental methods for studying spray penetration. SAE Trans. 1881-1884. https://www.jstor.org/stable/44651829.

[7]

Delacourt, E., Desmet, B., Besson, B., 2005. Characterisation of very high pressure diesel sprays using digital imaging techniques. Fuel 84 (7-8), 859-867. https://doi.org/10.1016/j.fuel.2004.12.003.

[8]

Desantes, J.M., Payri, R., Salvador, F.J., Gil, A., 2006a. Development and validation of a theoretical model for diesel spray penetration. Fuel 85 (7-8), 910-917. https://doi.org/10.1016/j.fuel.2005.10.023.

[9]

Desantes, J.M., Payri, R., Salvador, F.J., Gimeno, J., 2006b. Prediction of spray penetration by means of spray momentum flux. SAE Technical Paper Series. https://doi.org/10.4271/2006-01-1387.

[10]

Gerald Liu, Z., Munnannur, A., 2019. Future diesel engines. In: Design and Development of Heavy Duty Diesel Engines. a Handbook. Springer Singapore, Singapore, pp. 887-914. https://doi.org/10.1007/978-981-15-0970-4_24.

[11]

Hiroyasu, H., Arai, M., 1990. Structures of fuel sprays in diesel engines. SAE Trans. 1050-1061. https://www.jstor.org/stable/44548562.

[12]

Inagaki, K., Mizuta, J., Kawamura, K., Idota, Y., Hashizume, T., 2016. Theoretical study on spray design for small-bore diesel engine (No. 2016-01-0740). SAE Technical Paper. https://doi.org/10.4271/2016-01-0740.

[13]

Jia, T.M., Li, G.X., Yu, Y.S., Xu, Y.J., 2016a. Effects of ultra-high injection pressure on penetration characteristics of diesel spray and a two-mode leading edge shock wave. Exp. Therm. Fluid Sci. 79, 126-133. https://doi.org/10.1016/j.expthermflusci.2016.07.006.

[14]

Jia, T.M., Li, G.X., Yu, Y.S., Xu, Y.J., 2016b. Propagation characteristics of induced shock waves generated by diesel spray under ultra-high injection pressure. Fuel 180, 521-528. https://doi.org/10.1016/j.fuel.2016.04.009.

[15]

Jin, Y., Zhai, C., Nishida, K., Ogata, Y., 2020. An analysis of diesel spray characteristics with small injection amount under similarity law condition. Small Engine Technol. Conf. Expo. 308417. https://doi.org/10.4271/2019-32-0590.

[16]

Kostas, J., Honnery, D., Soria, J., 2009. Time resolved measurements of the initial stages of fuel spray penetration. Fuel 88 (11), 2225-2237. https://doi.org/10.1016/j.fuel.2009.05.013.

[17]

Kothiwale, G.R., Akkoli, K.M., Doddamani, B.M., Kattimani, S.S., Ağbulut, Ü., Afzal, A., Kaladgi, A.R., Said, Z., 2023. Impact of injector nozzle diameter and hole number on performance and emission characteristics of CI engine powered by nanoparticles. Int. J. Environ. Sci. Technol. 20, 5013-5034. https://doi.org/10.1007/s13762-022-04397-0, 2023.

[18]

Luo, H., Jin, Y., Zhai, C., Chang, F., Xing, W., Nishida, K., Ogata, Y., 2023. Very low soot formation with modulated liquid length and lift-off length of diesel spray flame. J. Energy Inst. 111, 101383. https://doi.org/10.1016/j.joei.2023.101383.

[19]

Mohan, B., Yang, W., kiang Chou, S., 2013. Fuel injection strategies for performance improvement and emissions reduction in compression ignition engines-A review. Renew. Sustain. Energy Rev. 28, 664-676. https://doi.org/10.1016/j.rser.2013.08.051.

[20]

Murugesan, A., Umarani, C., Subramanian, R., Nedunchezhian, N., 2009. Bio-diesel as an alternative fuel for diesel engines-a review. Renew. Sustain. Energy Rev. 13 (3), 653-662. https://doi.org/10.1016/j.rser.2007.10.007.

[21]

Ouyang, G., An, S., Liu, Z., Li, Y., 2019. Common Rail Fuel Injection Technology in Diesel Engines. John Wiley & Sons.

[22]

Pandey, R.K., Rehman, A., Sarviya, R.M., 2012. Impact of alternative fuel properties on fuel spray behavior and atomization. Renew. Sustain. Energy Rev. 16 (3), 1762-1778. https://doi.org/10.1016/j.rser.2011.11.010.

[23]

Park, S.H., Youn, I.M., Lim, Y., Lee, C.S., 2013. Influence of the mixture of gasoline and diesel fuels on droplet atomization, combustion, and exhaust emission characteristics in a compression ignition engine. Fuel Process. Technol. 106, 392-401. https://doi.org/10.1016/j.fuproc.2012.09.004.

[24]

Siebers, D.L., 1998. Liquid-phase fuel penetration in diesel sprays. SAE Trans. 1205-1227. https://www.jstor.org/stable/44736606.

[25]

Stager, L.A., Reitz, R.D., 2007. Assessment of diesel engine size-scaling relationships (No. 2007-01-0127). SAE Technical Paper. https://doi.org/10.4271/2007-01-0127.

[26]

Shi, Y., Reitz, R.D., 2008. Study of diesel engine size-scaling relationships based on turbulence and chemistry scales (No. 2008-01-0955). SAE Technical Paper. https://doi.org/10.4271/2008-01-0955.

[27]

Suzuki, T., Ohshima, R., 2002. An experimental Study on diesel spray Behavior-Non-dimensional expression for spray Tip penetration. Mar. Eng. 37 (3), 213-219. https://doi.org/10.5988/jime.37.213.

[28]

Vera-Tudela, W., Haefeli, R., Barro, C., Schneider, B., Boulouchos, K., 2020. An experimental study of a very high-pressure diesel injector (up to 5000 bar) by means of optical diagnostics. Fuel 275, 117933. https://doi.org/10.1016/j.fuel.2020.117933.

[29]

Wang, L., Lowrie, J., Ngaile, G., Fang, T., 2019. High injection pressure diesel sprays from a piezoelectric fuel injector. Appl. Therm. Eng. 152, 807-824. https://doi.org/10.1016/j.applthermaleng.2019.02.095.

[30]

Wakuri, Y., Fujii, M., Amitani, T., Tsuneya, R., 1960. Studies on the penetration of fuel spray in a diesel engine. Bull.JSME 3 (9), 123-130. https://doi.org/10.1299/jsme1958.3.123.

[31]

Xin, Q., 2011. Diesel Engine System Design. Elsevier.

[32]

Xia, J., Huang, Z., Xu, L., Ju, D., Lu, X., 2019. Experimental study on spray and atomization characteristics under subcritical, transcritical and supercritical conditions of marine diesel engine. Energy Convers. Manag. 195, 958-971. https://doi.org/10.1016/j.enconman.2019.05.080.

[33]

Yu, S., Yu, M., Sun, P., Wang, J., Xu, J., 2026. Spray and combustion characteristics of−10 diesel and−50 biodiesel under various injection pressures in a constant-volume combustion chamber. Energy 342, 139688. https://doi.org/10.1016/j.energy.2025.139688.

[34]

Zhai, C., Jin, Y., Nishida, K., Ogata, Y., 2021a. Diesel spray and combustion of multi-hole injectors with micro-hole under ultra-high injection pressure-non-evaporating spray characteristics. Fuel 283, 119322. https://doi.org/10.1016/j.fuel.2020.119322.

[35]

Zhai, C., Jin, Y., Wu, Q., Nishida, K., Ogata, Y., 2021b. Diesel spray and combustion of multi-hole injectors with micro-hole under ultra-high injection pressure-combustion characteristics. Fuel 300, 120949. https://doi.org/10.1016/j.fuel.2021.120949.

[36]

Zhai, C., Zhang, G., Jin, Y., Nishida, K., Ogata, Y., Luo, H., 2022a. Characterization of diesel spray combustion using two-color pyrometry and OH* chemiluminescence imaging-comparison between micro-hole and ultra-high injection pressure effects. J. Energy Inst. 103, 104-116. https://doi.org/10.1016/j.joei.2022.05.012.

[37]

Zhai, C., Jin, Y., Wu, Q., Nishida, K., Ogata, Y., 2022b. Diesel spray of multi-hole injectors with micro-hole under ultra-high injection pressure-evaporating spray characteristics. Atomization Sprays 32 (1). https://doi.org/10.1615/AtomizSpr.2021037966.

[38]

Zhai, C., Chang, F., Jin, Y., Luo, H., 2023a. Investigations on the diesel spray characteristic and tip penetration model of multi-hole injector with micro-hole under ultra-high injection pressure. Sustainability 15 (14), 11114. https://doi.org/10.3390/su151411114.

[39]

Zhai, C., Jin, Y., Feng, Z., Chang, F., Luo, H., Nishida, K., Ogata, Y., 2023b. Characterization of diesel spray combustion under micro-hole and ultra-high injection pressure conditions-analyses of diffused back-illumination imaging and OH* chemiluminescence imaging. Fuel Process. Technol. 252, 107955. https://doi.org/10.1016/j.fuproc.2023.107955.

[40]

Zhai, C., Liu, E., Zhang, G., Xing, W., Chang, F., Jin, Y., Luo, H., Nishida, K., Ogata, Y., 2024. Similarity and normalization study of fuel spray and combustion under ultra-high injection pressure and micro-hole diameter conditions-spray characteristics. Energy 288, 129684. https://doi.org/10.1016/j.energy.2023.129684.

[41]

Zhai, C., Zhang, J., Li, K., Dong, P., Jin, Y., Chang, F., Luo, H., 2025. Comparative analysis and normalization of single-hole vs. multi-hole spray characteristics: 1st report on spray characteristic comparison. Green Energy Resour. 3 (1), 100120. https://doi.org/10.1016/j.gerr.2025.100120.

[42]

Zhou, X., Li, T., Lai, Z., Wang, B., 2018. Scaling fuel sprays for different size diesel engines. Fuel 225, 358-369. https://doi.org/10.1016/j.fuel.2018.03.167.

[43]

Zhou, X., Li, T., 2021. Modeling of the entire processes of diesel spray tip penetration including the start-and end-of-injection transients. J. Energy Inst. 98, 271-281. https://doi.org/10.1016/j.joei.2021.07.007.

[44]

Zhou, Y., Pei, J., Ding, S., Zhao, S., Zhu, K., Shao, L., Zhong, Z., Du, F., Li, X., Xu, Z., 2024. Theoretical model for high-altitude gas exchange process in multi-fuel poppet valves two-stroke aircraft engine. Energy Convers. Manag. 301, 118028. https://doi.org/10.1016/j.enconman.2023.118028.

[45]

Zhang, J., Feng, Z., Gu, J., Jin, Y., Leng, X., Huang, R., He, Z., 2026. Decoupling the effect of viscosity and surface tension on fuel atomization characteristics. Phys. Fluids 38 (1). https://doi.org/10.1063/5.0309846.

PDF (7640KB)

0

Accesses

0

Citation

Detail

Sections
Recommended

/

〈 〉