Electron-donor/-acceptor ratio-guided molecular engineering for buried interface optimization in n-i-p perovskite solar cells

Abstract

The buried interface between the electron transport layer (ETL) and perovskite is critical for the performance of perovskite solar cells (PSCs). Modifying the microstructure of this buried interface using dipolar molecules is among the most effective strategies to enhance device performance. However, the influence of the electron-donating/electron- withdrawing group ratio (EDG/EWG ratio) of dipolar molecules on buried interface engineering has not been systematically investigated. In this work, dipolar molecules are classified into EWG-rich, balanced, and EDG-rich configurations according to their EDG/EWG ratio, using L-aspartic acid, 4-aminobutyric acid, and L-2,4-diaminobutyric acid (DBA) as model systems. We confirm that the primary factor limiting device performance is located on the perovskite side rather than the ETL side. Both experimental and theoretical results reveal that the EDG-rich dipolar configuration provides the most efficient defect passivation for perovskite, promotes the growth of high-quality perovskite films, strengthens the interfacial electric field, and accelerates interfacial electron extraction and transport. As a result, the DBA-modified device achieves a champion PCE of 24.18% and maintains 85% of its initial efficiency after 30 days of ambient storage (20-25 °C, 25%-30% relative humidity) without encapsulation, showing excellent long-term stability. This work establishes asymmetric molecular engineering as a key design principle for optimizing the buried interface in high-performance PSCs.

Keywords

Perovskite solar cells / dipolar molecules / the buried interface / defect passivation / asymmetric molecular engineering

References

[1] Fan Y.,Qin Z.,Lu L..et al. An efficient and precise solution-vacuum hybrid batch fabrication of 2D/3D perovskite submodules Nat. Commun. 2025 16 7019 PMC12314120

[2] Li Q.,Liu H.,Hou C..et al. Harmonizing the bilateral bond strength of the interfacial molecule in perovskite solar cells Nat. Energy 2024 9 1506 16

[3] Xu H.,Xiao Y.,Elmestekawy K. A..et al. Metastable interphase induced pre-strain compensation enables efficient and stable perovskite solar cells Energy Environ. Sci. 2025 18 246 55

[4] Xu R.,Wang C.,Zhang Z..et al. Buried interface engineering: a key to unlocking the potential of self-assembled monolayer (SAM)-based inverted perovskite solar cells Small 2025 21 e2503114

[5] Bi H.,Zuo X.,Liu B..et al. Multifunctional organic ammonium salt-modified SnO₂ nanoparticles toward efficient and stable planar perovskite solar cells J. Mater. Chem. A. 2021 9 3940 51

[6] Wei K.,Yang L.,Deng J.,Luo Z.,Zhang X.,Zhang J.. Facile exfoliation of the perovskite thin film for visualizing the buried interfaces in perovskite solar cells ACS Appl. Energy Mater. 2022 5 7458 65

[7] Wang L.,Xia J.,Yan Z..et al. Robust interfacial modifier for efficient perovskite solar cells: reconstruction of energy alignment at buried interface by self-diffusion of dopants Adv. Funct. Mater. 2022 32 2204725

[8] Wu M.,Duan Y.,Yang L..et al. Multifunctional small molecule as buried interface passivator for efficient planar perovskite solar cells Adv. Funct. Mater. 2023 33 2300128

[9] Deng C.,Wu J.,Yang Y..et al. Modulating residual lead iodide via functionalized buried interface for efficient and stable perovskite solar cells ACS Energy Lett. 2022 8 666 76

[10] Ge Y.,Ye F.,Xiao M..et al. Internal encapsulation for lead halide perovskite films for efficient and very stable solar cells Adv. Energy Mater. 2022 12 2200361

[11] Xiong Q.,Wang C.,Zhou Q..et al. Rear interface engineering to suppress migration of iodide ions for efficient perovskite solar cells with minimized hysteresis Adv. Funct. Mater. 2021 32 2107823

[12] Li H.,Xie G.,Wang X..et al. Buried interface dielectric layer engineering for highly efficient and stable inverted perovskite solar cells and modules Adv. Sci. 2023 10 e2300586 PMC10323608

[13] Chen Y.,Zuo X.,He Y..et al. Dual passivation of perovskite and SnO₂ for high-efficiency MAPbI₃ perovskite solar cells Adv. Sci. 2021 8 2001466 PMC7927604

[14] Xia H.,Li X.,Zhou J..et al. Interfacial chemical bridge constructed by zwitterionic sulfamic acid for efficient and stable perovskite solar cells ACS Appl. Energy Mater. 2020 3 3186 92

[15] Kim G.,Choi Y.,Choi H.,Min J.,Park T.,Song S.. Novel cathode interfacial layer using creatine for enhancing the photovoltaic properties of perovskite solar cells J. Mater. Chem. A. 2020 8 21721 8

[16] Qin Z.,Chen Y.,Wang X..et al. Zwitterion-functionalized SnO₂ substrate induced sequential deposition of black-phase FAPbI₃ with rearranged PbI₂ residue Adv. Mater. 2022 34 e2203143

[17] Geng Q.,Jia X.,He Z..et al. Interface engineering via amino acid for efficient and stable perovskite solar cells Adv. Mater. Interfaces 2022 9 2201641

[18] Liu S.,Li J.,Xiao W..et al. Buried interface molecular hybrid for inverted perovskite solar cells Nature 2024 632 536 42

[19] Jiang X.,Qin S.,Meng L..et al. Isomeric diammonium passivation for perovskite-organic tandem solar cells Nature 2024 635 860 6

[20] Peng W.,Zhang Y.,Zhou X..et al. A versatile energy-level-tunable hole-transport layer for multi-composition inverted perovskite solar cells Energy Environ. Sci. 2025 18 874 83

[21] Wei Z.,Zhou Q.,Niu X..et al. Surpassing 90% Shockley-Queisser V_OC limit in 1.79 eV wide-bandgap perovskite solar cells using bromine-substituted self-assembled monolayers Energy Environ. Sci. 2025 18 1847 55

[22] Gao L.,He Z.,Zeng K.,Liu A.,Jiang F.,Ma T.. Ultralow-temperature SnO₂ electron transport layers fabricated by intermediate-controlled chemical bath deposition for highly efficient perovskite solar cells ChemSusChem 2023 16 e202300765

[23] Chen Z.,Jiang S.,Du X..et al. Three-dimensional (3D) fluoride molecular glue to improve the SnO₂/perovskite interface for efficient perovskite solar cells Angew. Chem. Int. Ed. Engl. 2025 64 e202415669

[24] Wang Y.,Ye J.,Song J..et al. Synchronous modulation of hole-selective self-assembled monolayer and buried interface for inverted perovskite solar cells Cell Rep. Phys. Sci. 2024 5 101992

[25] Shi C.,Wang J.,Lei X..et al. Modulating competitive adsorption of hybrid self-assembled molecules for efficient wide-bandgap perovskite solar cells and tandems Nat. Commun. 2025 16 3029 PMC11953228

[26] Zhou H.,Wang W.,Duan Y..et al. Glycol monomethyl ether-substituted carbazolyl hole-transporting material for stable inverted perovskite solar cells with efficiency of 25.52% Angew. Chem. Int. Ed. Engl. 2024 63 e202403068

[27] Torres Merino L. V.,Petoukhoff C. E.,Matiash O..et al. Impact of the valence band energy alignment at the hole-collecting interface on the photostability of wide band-gap perovskite solar cells Joule 2024 8 2585 606

[28] Wang R.,Wu C.,Qi J..et al. Side-chain methylthio-based position isomerism of hole-transport materials for perovskite solar cells: from theoretical simulation to experimental characterization Adv. Funct. Mater. 2023 33 2213843

[29] Farag A.,Feeney T.,Hossain I. M..et al. Evaporated self-assembled monolayer hole transport layers: lossless interfaces in p-i-n perovskite solar cells Adv. Energy Mater. 2023 13 2203982

[30] Wei Y.,Tang Y.,Li H..et al. Decreased hysteresis benefited from enhanced lattice oxygen and promoted band alignment with electron transport layer modification in perovskite solar cells ACS Appl. Mater. Interfaces 2025 17 11278 86

[31] Chen Q.,Yang X.,Zhou Y.,Song B.. Zwitterions: promising interfacial/doping materials for organic/perovskite solar cells New J. Chem. 2021 45 15118 30

[32] Liu J.,Li S.,Liu S..et al. Oxygen vacancy management for high-temperature mesoporous SnO₂ electron transport layers in printable perovskite solar cells Angew. Chem. Int. Ed. Engl. 2022 61 e202202012

[33] Mallik N.,Hajhemati J.,Frégnaux M..et al. Interface defect formation for atomic layer deposition of SnO₂ on metal halide perovskites Nano Energy 2024 126 109582

[34] Fu S.,Sun N.,Chen H..et al. On-demand formation of Lewis bases for efficient and stable perovskite solar cells Nat. Nanotechnol. 2025 20 772 8

[35] Zhou Q.,He D.,Zhuang Q..et al. Revealing steric-hindrance-dependent buried interface defect passivation mechanism in efficient and stable perovskite solar cells with mitigated tensile stress Adv. Funct. Mater. 2022 32 2205507

[36] Kong W.,Zhu D.,Zhang Y..et al. Electron donor coordinated metal-organic framework to enhance photoelectrochemical performance Angew. Chem. Int. Ed. Engl. 2023 62 e202308514

[37] Wang K.,Hong Q.,Zhu C..et al. Metal-ligand dual-site single-atom nanozyme mimicking urate oxidase with high substrates specificity Nat. Commun. 2024 15 5705 PMC11231224

[38] Ma L.,Yao H.,Wang J..et al. Impact of electrostatic interaction on bulk morphology in efficient donor-acceptor photovoltaic blends Angew. Chem. Int. Ed. Engl. 2021 60 15988 94

[39] Zhang L.,Cao K.,Qian J..et al. Crystallization control and multisite passivation of perovskites with amino acid to boost the efficiency and stability of perovskite solar cells J. Mater. Chem. C. 2020 8 17482 90

[40] Du J.,Feng L.,Guo X..et al. Enhanced efficiency and stability of planar perovskite solar cells by introducing amino acid to SnO₂/perovskite interface J. Power Sources 2020 455 227974

[41] Li Y.,Zhao C.,Wang L..et al. Self-assembled manganese acetate@tin dioxide colloidal quantum dots as an electron-transport layer for efficient and stable perovskite solar cells Inorg. Chem. Front. 2024 11 3566 77

[42] Liu B.,Zhou Q.,Li Y..et al. Polydentate ligand reinforced chelating to stabilize buried interface toward high-performance perovskite solar cells Angew. Chem. Int. Ed. Engl. 2024 63 e202317185

[43] Li T.,Wang S.,Yang J..et al. Multiple functional groups synergistically improve the performance of inverted planar perovskite solar cells Nano Energy 2021 82 105742

[44] Canil L.,Cramer T.,Fraboni B..et al. Tuning halide perovskite energy levels Energy Environ. Sci. 2021 14 1429 38

[45] Li Z.,Wang C.,Sun P..et al. In-situ peptization of WO₃ in alkaline SnO₂ colloid for stable perovskite solar cells with record fill-factor approaching the shockley-queisser limit Nano Energy 2022 100 107468

[46] Yu X.,Lv Y.,Xue B..et al. Multiple bonding effects of 1-methanesulfonyl-piperazine on the two-step processed perovskite towards efficient and stable solar cells Nano Energy 2022 93 106856

[47] Su P.,Bi H.,Ran D..et al. Multifunctional and multi-site interfacial buffer layer for efficient and stable perovskite solar cells Chem. Eng. J. 2023 472 145077

[48] Su H.,Xu Z.,He X..et al. Surface energy engineering of buried interface for highly stable perovskite solar cells with efficiency over 25 Adv. Mater. 2024 36 e2306724

[49] Xu X.,Sun Y.,He D..et al. Grain size control for high-performance formamidinium-based perovskite solar cells via suppressing heterogenous nucleation J. Mater. Chem. C. 2021 9 208 13

[50] Jiang X.,Zhang B.,Yang G..et al. Molecular dipole engineering of carbonyl additives for efficient and stable perovskite solar cells Angew. Chem. Int. Ed. Engl. 2023 62 e202302462

[51] Du Y.,Tian Q.,Chang X..et al. Ionic liquid treatment for highest-efficiency ambient printed stable all-inorganic CsPbI₃ perovskite solar cells Adv. Mater. 2022 34 e2106750

[52] Aranda C. A.,Alvarez A. O.,Chivrony V. S.,Das C.,Rai M.,Saliba M.. Overcoming ionic migration in perovskite solar cells through alkali metals Joule 2024 8 241 54

[53] Li F.,Deng X.,Shi Z..et al. Hydrogen-bond-bridged intermediate for perovskite solar cells with enhanced efficiency and stability Nat. Photonics 2023 17 478 84

[54] Ceratti D. R.,Zohar A.,Kozlov R..et al. Eppur si muove: proton diffusion in halide perovskite single crystals Adv. Mater. 2020 32 e2002467

[55] Zhang Y.,Kong T.,Xie H..et al. Molecularly tailored SnO₂/perovskite interface enabling efficient and stable FAPbI₃ solar cells ACS Energy Lett. 2022 7 929 38

[56] Sun Y.,Zhang J.,Yu H.,Wang J.,Huang C.,Huang J.. Mechanism of bifunctional p-amino benzenesulfonic acid modified interface in perovskite solar cells Chem. Eng. J. 2021 420 129579

[57] Lei Y.,Li Z.,Wang H..et al. Manipulate energy transport via fluorinated spacers towards record-efficiency 2D Dion-Jacobson CsPbI₃ solar cells Sci. Bull. 2022 67 1352 61

[58] Zhan S.,Duan Y.,Liu Z..et al. Stable 24.29%-efficiency FA_0.85MA_0.15PbI₃ perovskite solar cells enabled by methyl haloacetate-lead dimer complex Adv. Energy Mater. 2022 12 2200867

[59] Liu Z.,Cao F.,Wang M.,Wang M.,Li L.. Observing defect passivation of the grain boundary with 2-aminoterephthalic acid for efficient and stable perovskite solar cells Angew. Chem. Int. Ed. Engl. 2020 59 4161 7

[60] Yang M.,Tan Y.,Yang G..et al. Chemical synergic stabilization of high Br-content mixed-halidewide-bandgap perovskites for durable multi-terminal tandemsolar cells with minimized Pb leakage Angew. Chem. Int. Ed. 2025 64 e202415966

[61] Liu G.,Jiang X.,Feng W..et al. Synergic electron and defect compensation minimizes voltage loss in lead-free perovskite solar cells Angew. Chem. Int. Ed. Engl. 2023 62 e202305551

[62] Liu G.,Zhong Y.,Feng W..et al. Multidentate chelation heals structural imperfections for minimized recombination loss in lead-free perovskite solar cells Angew. Chem. Int. Ed. Engl. 2022 61 e202209464