Engineering strategies for high-voltage LiCoO₂ based high-energy Li-ion batteries

Abstract

To drive electronic devices for a long range, the energy density of Li-ion batteries must be further enhanced, and high-energy cathode materials are required. Among the cathode materials, LiCoO₂ (LCO) is one of the most promising candidates when charged to higher voltages over 4.3 V. However, high-voltage LCO materials are confronted with severe surface and bulk issues inducing poor cyclic stability. To completely unleash the potential of LCO cathodes, a more comprehensive theoretical understanding of the underlying issues is necessary, along with active exploration of previous modifications. This paper mainly presents the degradation mechanisms of LCO under high voltage, the formation and evolution mechanisms of the cathode electrolyte interface, and the surface engineering strategies employed to enhance the cell performance. By organizing and summarizing these modifications, this work aims to establish associations among common research issues and to suggest future research priorities, thus facilitating the rapid development of high-voltage LCO.

Keywords

coating / doping / electrolyte additives / high-voltage LiCoO ₂ / lithium-ion batteries

References

[1] Kim U-H, Park G-T, Son B-K, et al. Heuristic solution for achieving long-term cycle stability for Ni-rich layered cathodes at full depth of discharge. Nat Energy. 2020;5(11):860.

[2] Yan P, Zheng J, Liu J, et al. Tailoring grain boundary structures and chemistry of Ni-rich layered cathodes for enhanced cycle stability of lithium-ion batteries. Nat Energy. 2018;3(7):600-605.

[3] Duan J, Tang X, Dai H, et al. Building safe lithium-ion batteries for electric vehicles: a review. Electrochem Energy Rev. 2019;3(1):1-42.

[4] Kim T, Song W, Son D-Y, Ono LK, Qi Y. Lithium-ion batteries: outlook on present, future, and hybridized technologies. J Mater Chem A. 2019;7(7):2942-2964.

[5] Gandoman FH, Jaguemont J, Goutam S, et al. Concept of reliability and safety assessment of lithium-ion batteries in electric vehicles: basics, progress, and challenges. Appl Energy. 2019;251:113343.

[6] Heng Y-L, Gu Z-Y, Guo J-Z, Yang X-T, Zhao X-X, Wu X-L. Research progress on the surface/interface modification of high-voltage lithium oxide cathode materials. Energy Mater. 2022;2(3):200017.

[7] Zhou M, Qin C, Liu Z, et al. Enhanced high voltage cyclability of LiCoO₂ cathode by adopting poly[bis-(ethoxyethoxyethoxy)phosphazene] with flame-retardant property as an electrolyte additive for lithium-ion batteries. Appl Surf Sci. 2017;403:260-266.

[8] Goodenough JB, Park K-S. The Li-ion rechargeable battery: a perspective. J Am Chem Soc. 2013;135(4):1167-1176.

[9] Liu J, Wang J, Ni Y, Zhang K, Cheng F, Chen J. Recent break-throughs and perspectives of high-energy layered oxide cathode materials for lithium ion batteries. Mater Today. 2021;43:132-165.

[10] Zheng J, Myeong S, Cho W, et al. Li-and Mn-rich cathode materials: challenges to commercialization. Adv Energy Mater. 2016;7(6):1601284.

[11] Berg EJ, Villevieille C, Streich D, Trabesinger S, Novák P. Rechargeable batteries: grasping for the limits of chemistry. J Electrochem Soc. 2015;162(14):A2468.

[12] Zuo W, Luo M, Liu X, et al. Li-rich cathodes for rechargeable Li-based batteries: reaction mechanisms and advanced characterization techniques. Energy Environ Sci. 2020;13(12):4450.

[13] Lyu Y, Wu X, Wang K, et al. An overview on the advances of LiCoO₂ cathodes for lithium-ion batteries. Adv Energy Mater. 2020;11(2):2000982.

[14] Li H, Wang L, Song Y, et al. Understanding the insight mechanism of chemical-mechanical degradation of layered Co-free Ni-rich cathode materials: a review. Small. 2023;19(32):2302208.

[15] Park KY, Zhu Y, Torres-Castanedo CG, et al. Elucidating and mitigating high-voltage degradation cascades in cobalt-free LiNiO₂ lithium-ion battery cathodes. Adv Mater. 2022;34(3):2106402.

[16] Zhao H, Lam WYA, Sheng L, et al. Cobalt-free cathode materials: families and their prospects. Adv Energy Mater. 2022;12(16):2103894.

[17] Fergus JW. Recent developments in cathode materials for lithium ion batteries. J Power Sources. 2010;195(4):939.

[18] Kong W, Zhang J, Wong D, et al. Tailoring CO3d and O2p band centers to inhibit oxygen escape for stable 4.6 V LiCoO₂ cathodes. Angew Chem, Int Ed. 2021;60(52):27102.

[19] Liu Q, Su X, Lei D, et al. Approaching the capacity limit of lithium cobalt oxide in lithium ion batteries via lanthanum and aluminium doping. Nat Energy. 2018;3(11):936.

[20] Fu A, Zhang Z, Lin J, et al. Highly stable operation of LiCoO₂ at cut-off ≥4.6 V enabled by synergistic structural and interfacial manipulation. Energy Storage Mater. 2022;46:406.

[21] Choi N-S, Han J-G, Ha S-Y, Park I, Back C-K. Recent advances in the electrolytes for interfacial stability of high-voltage cathodes in lithium-ion batteries. RSC Adv. 2015;5(4):2732.

[22] Kalluri S, Yoon M, Jo M, et al. Surface engineering strategies of layered LiCoO₂ cathode material to realize high-energy and high-voltage Li-ion cells. Adv Energy Mater. 2017;7(1):1601507.

[23] Song Y, Liu X, Ren D, et al. Simultaneously blocking chemical crosstalk and internal short circuit via gel-stretching derived nanoporous non-shrinkage separator for safe lithium-ion batteries. Adv Mater. 2022;34(2):2106335.

[24] Wang K, Wan J, Xiang Y, et al. Recent advances and historical developments of high voltage lithium cobalt oxide materials for rechargeable Li-ion batteries. J Power Sources. 2020;460:228062.

[25] Zhang F, Lou S, Li S, et al. Surface regulation enables high stability of single-crystal lithium-ion cathodes at high voltage. Nat Commun. 2020;11(1):3050.

[26] Chen Z, Dahn JR. Methods to obtain excellent capacity retention in LiCoO₂ cycled to 4.5 V. Electrochim Acta. 2004;49(7):1079.

[27] Xu C, Reeves PJ, Jacquet Q, Grey CP. Phase behavior during electrochemical cycling of Ni-rich cathode materials for Li-ion batteries. Adv Energy Mater. 2020;11(7):2003404.

[28] Tebbe JL, Holder AM, Musgrave CB. Mechanisms of LiCoO₂ cathode degradation by reaction with HF and protection by thin oxide coatings. ACS Appl Mater Interfaces. 2015;7(43):24265.

[29] Xiang Q, Li L, Wang L, Zhou C, Zhang D, Li Z. Inhibiting degradation of LiCoO₂ cathode material by anisotropic strain during delithiation. Mater Res Express. 2020;7(2):025501.

[30] Jiang Y, Qin C, Yan P, Sui M. Origins of capacity and voltage fading of LiCoO₂ upon high voltage cycling. J Mater Chem A. 2019;7(36):20824.

[31] Yano A, Shikano M, Ueda A, Sakaebe H, Ogumi Z. LiCoO₂ degradation behavior in the high-voltage phase transition region and improved reversibility with surface coating. J Electrochem Soc. 2016;164(1):A6116.

[32] Imanishi N, Fujiyoshi M, Takeda Y, Yamamoto O, Tabuchi M. Preparation and ⁷Li-NMR study of chemically delithiated Li_1-xCoO₂ (0<x<0.5). Solid State Ionics. 1999;118(1):121.

[33] Milewska A, Świerczek K, Tobola J, et al. The nature of the nonmetal-metal transition in LixCoO₂ oxide. Solid State Ionics. 2014;263:110.

[34] Chang K, Hallstedt B, Music D, et al. Thermodynamic description of the layered O3 and O2 structural LiCoO₂–CoO₂ pseudo-binary systems. Calphad. 2013;41:6.

[35] Wu N, Zhang Y, Guo Y, Liu S, Liu H, Wu H. Flakelike LiCoO₂ with exposed 010 facets as a stable cathode material for highly reversible lithium storage. ACS Appl Mater Interfaces. 2016;8(4):2723.

[36] Xu Z, Hou D, Kautz DJ, et al. Charging reactions promoted by geometrically necessary dislocations in battery materials revealed by in situ single-particle synchrotron measurements. Adv Mater. 2020;32(37):2003417.

[37] Jiang Y, Yan P, Yu M, et al. Atomistic mechanism of cracking degradation at twin boundary of LiCoO₂. Nano Energy. 2020;78:105364.

[38] Zhu Z, Yu D, Shi Z, et al. Gradient-morph LiCoO₂ single crystals with stabilized energy density above 3400 W h L^-1. Energy Environ Sci. 2020;13(6):1865.

[39] Abouimrane A, Belharouak I, Amine K. Sulfone-based electrolytes for high-voltage Li-ion batteries. Electrochem Commun. 2009;11(5):1073.

[40] Hu B, Geng F, Shen M, et al. A multifunctional manipulation to stabilize oxygen redox and phase transition in 4.6 V high-voltage LiCoO₂ with sXAS and EPR studies. J Power Sources. 2021;516:230661.

[41] Mu L, Lin R, Xu R, et al. Oxygen release induced chemo-mechanical breakdown of layered cathode materials. Nano Lett. 2018;18(5):3241.

[42] Hong J, Lim H-D, Lee M, et al. Critical role of oxygen evolved from layered Li–excess metal oxides in lithium rechargeable batteries. Chem Mater. 2012;24(14):2692.

[43] Lee J, Papp JK, Clement RJ, et al. Mitigating oxygen loss to improve the cycling performance of high capacity cation-disordered cathode materials. Nat Commun. 2017;8(1):981.

[44] Ramakrishnan S, Park B, Wu J, Yang W, McCloskey BD. Extended interfacial stability through simple acid rinsing in a Li-rich oxide cathode material. J Am Chem Soc. 2020;142(18):8522.

[45] He Y, Wang L, Zhang B, et al. Atomic-scale insight into the lattice volume plunge of LixCoO₂ upon deep delithiation. Energy Adv. 2023;2(1):103.

[46] Xu G, Li J, Wang C, et al. The formation/decomposition equilibrium of LiH and its contribution on anode failure in practical lithium metal batteries. Angew Chem, Int Ed. 2021;60(14):7770.

[47] Metzger M, Strehle B, Solchenbach S, Gasteiger HA. Origin of H₂ evolution in LIBs: H₂O reduction vs. electrolyte oxidation. J Electrochem Soc. 2016;163(5):A798.

[48] Wang X, Ren D, Liang H, et al. Ni crossover catalysis: truth of hydrogen evolution in Ni-rich cathode-based lithium-ion batteries. Energy Environ Sci. 2023;16(3):1200.

[49] Ohnishi T, Mitsuishi K, Takada K. In situ X-ray diffraction of LiCoO₂ in thin-film batteries under high-voltage charging. ACS Appl Energy Mater. 2021;4(12):14372.

[50] Lin F, Markus IM, Nordlund D, et al. Surface reconstruction and chemical evolution of stoichiometric layered cathode materials for lithium-ion batteries. Nat Commun. 2014;5:3529.

[51] Zhang J-N, Li Q, Wang Y, Zheng J, Yu X, Li H. Dynamic evolution of cathode electrolyte interphase (CEI) on high voltage LiCoO₂ cathode and its interaction with Li anode. Energy Storage Mater. 2018;14:1.

[52] Mao S, Mao J, Shen Z, et al. Specific adsorption-oxidation strategy in cathode inner Helmholtz plane enabling 4.6 V practical lithium-ion full cells. Nano Lett. 2023;23(15):7014.

[53] Bai P, Ji X, Zhang J, et al. Formation of LiF-rich cathode-electrolyte interphase by electrolyte reduction. Angew Chem, Int Ed. 2022;61(26):e202202731.

[54] Zhou H, Izumi J, Asano S, et al. Fast lithium intercalation mechanism on surface-modified cathodes for lithium-ion batteries. Adv Energy Mater. 2023;13(44):2302402.

[55] Thapaliya BP, Wang T, Borisevich AY, et al. In situ ion-exchange metathesis induced conformal LiF surface films on cathode (NMC811) as a cathode electrolyte interphase. Adv Funct Mater. 2023;33(44):2302443.

[56] Chen Y, He Q, Mo Y, et al. Engineering an insoluble cathode electrolyte interphase enabling high performance NCM811//graphite Pouch cell at 60°C. Adv Energy Mater. 2022;12(33):2201631.

[57] Lu W, Zhang J, Xu J, Wu X, Chen L. In situ visualized cathode electrolyte interphase on LiCoO₂ in high voltage cycling. ACS Appl Mater Interfaces. 2017;9(22):19313.

[58] Ren X, Zhang X, Shadike Z, et al. Designing advanced in situ electrode/electrolyte interphases for wide temperature operation of 4.5 V Li||LiCoO₂ batteries. Adv Mater. 2020;32(49):2004898.

[59] Liu J, Wang J, Ni Y, et al. Tuning interphase chemistry to stabilize high-voltage LiCoO₂ cathode material via spinel coating. Angew Chem, Int Ed. 2022;61(35):e202207000.

[60] Fathi R, Burns JC, Stevens DA, et al. Ultra high-precision studies of degradation mechanisms in aged LiCoO₂/graphite Li-ion cells. J Electrochem Soc. 2014;161(10): A1572-A1579.

[61] Tan S, Ji YJ, Zhang ZR, Yang Y. Recent progress in research on high-voltage electrolytes for lithium-ion batteries. ChemPhysChem. 2014;15(10):1956-1969.

[62] Ruan D, Chen M, Wen X, et al. In situ constructing a stable interface film on high-voltage LiCoO₂ cathode via a novel electrolyte additive. Nano Energy. 2021;90:106535.

[63] Zheng Y, Fang W, Zheng H, et al. A multifunctional thiophene-based electrolyte additive for lithium metal batteries using high-voltage LiCoO₂ cathode. J Electrochem Soc. 2019;166(14): A3222-A3227.

[64] Ge J, Liang H, Zhou M, et al. Phosphonate-functionalized ionic liquid: a novel electrolyte additive for eenhanced cyclic stability and rate capability of LiCoO₂ cathode at high voltage. ChemistrySelect. 2019;4(34):9959.

[65] Yang C, Liao X, Zhou X, et al. Phosphate-rich interface for a highly stable and safe 4.6 V LiCoO₂ cathode. Adv Mater. 2023;35(14):2210966.

[66] Zhang Z, Liu F, Huang Z, et al. Enhancing the electrochemical performance of a high-voltage LiCoO₂ cathode with a bifunctional electrolyte additive. ACS Appl Energy Mater. 2021;4(11):12954.

[67] Wen X, Chen M, Zhou X, et al. Synergetic effect of electrolyte coadditives for a high-voltage LiCoO₂ cathode. J Phys Chem C. 2021;126(1):282.

[68] Sun Y, Huang J, Xiang H, Liang X, Feng Y, Yu Y. 2-(Trifluoroacetyl) thiophene as an electrolyte additive for high-voltage lithium-ion batteries using LiCoO₂ cathode. J Mater Sci Technol. 2020;55:198.

[69] Ota H, Kominato A, Chun W-J, Yasukawa E, Kasuya S. Effect of cyclic phosphate additive in non-flammable electrolyte. J Power Sources. 2003;119-121:393.

[70] Nam ND, Park IJ, Kim JG. Triethyl and tributyl phosphite as flame-retarding additives in Li-ion batteries. Met Mater Int. 2012;18(1):189.

[71] Deng K, Zeng Q, Wang D, et al. Nonflammable organic electrolytes for high-safety lithium-ion batteries. Energy Storage Mater. 2020;32:425.

[72] Sun Z, Zhou H, Luo X, Che Y, Li W, Xu M. Design of a novel electrolyte additive for high voltage LiCoO₂ cathode lithium-ion batteries: lithium 4-benzonitrile trimethyl borate. J Power Sources. 2021;503:230033.

[73] Duncan H, Salem N, Abu-Lebdeh Y. Electrolyte formulations based on dinitrile solvents for high voltage Li-ion batteries. J Electrochem Soc. 2013;160(6): A838-A848.

[74] Xian F, Li J, Hu Z, et al. Investigation of the cathodic interfacial stability of a nitrile electrolyte and its performance with a high-voltage LiCoO₂ cathode. Chem Commun. 2020;56(37):4998-5001.

[75] Nisar U, Muralidharan N, Essehli R, Amin R, Belharouak I. Valuation of surface coatings in high-energy density lithium-ion battery cathode materials. Energy Storage Mater. 2021;38:309-328.

[76] Guan P, Zhou L, Yu Z, et al. Recent progress of surface coating on cathode materials for high-performance lithium-ion batteries. J Energy Chem. 2020;43:220-235.

[77] Hu Q, He Y, Ren D, et al. Targeted masking enables stable cycling of LiNi_0.6CO_0.2MN_0.2O₂ at 4.6V. Nano Energy. 2022;96:107123.

[78] Jung SC, Han Y-K. How do Li atoms pass through the Al₂O₃ coating layer during lithiation in Li-ion batteries? J Phys Chem Lett. 2013;4(16):2681-2685.

[79] Kim JW, Kim DH, Oh DY, et al. Surface chemistry of LiNi_0.5MN_1.5O₄ particles coated by Al₂O₃ using atomic layer deposition for lithium-ion batteries. J Power Sources. 2015;274:1254-1262.

[80] Wang X, Yushin G. Chemical vapor deposition and atomic layer deposition for advanced lithium ion batteries and supercapacitors. Energy Environ Sci. 2015;8(7):1889-1904.

[81] Hou Q, Cao G, Wang P, et al. Carbon coating nanostructured-LiNi_1/3CO_1/3MN_1/3O₂ cathode material synthesized by chemical vapor deposition method for high performance lithium-ion batteries. J Alloys Compd. 2018;747:796-802.

[82] Hu Q, Liao J, Xiao X, et al. Ultrahigh rate capability of manganese based olivine cathodes enabled by interfacial electron transport enhancement. Nano Energy. 2022;104:107895.

[83] Hao S, Wolverton C. Lithium transport in amorphous Al₂O₃ and AlF₃ for discovery of battery coatings. J Phys Chem C. 2013;117(16):8009-8013.

[84] Lee Y, Lee J, Lee KY, Mun J, Lee JK, Choi W. Facile formation of a Li₃PO₄ coating layer during the synthesis of a lithium-rich layered oxide for high-capacity lithium-ion batteries. J Power Sources. 2016;315:284-293.

[85] Li H, Zhou H. Enhancing the performances of Li-ion batteries by carbon-coating: present and future. Chem Commun. 2012;48(9):1201-1217.

[86] Zhou A, Xu J, Dai X, et al. Improved high-voltage and high-temperature electrochemical performances of LiCoO₂ cathode by electrode sputter-coating with Li₃PO₄. J Power Sources. 2016;322:10-16.

[87] Sun C, Zhao B, Mao J, et al. Enhanced cycling stability of 4.6 V LiCoO₂ cathodes by inhibiting catalytic activity of its interface via MXene modification. Adv Funct Mater. 2023;33(30):2300589.

[88] Xie J, Sendek AD, Cubuk ED, et al. Atomic layer deposition of stable LiAlF₄ lithium ion conductive interfacial layer for stable cathode cycling. ACS Nano. 2017;11(7):7019-7027.

[89] Zhou A, Lu Y, Wang Q, et al. Sputtering TiO₂ on LiCoO₂ composite electrodes as a simple and effective coating to enhance high-voltage cathode performance. J Power Sources. 2017;346:24-30.

[90] Zhou Y, Lee Y, Sun H, Wallas JM, George SM, Xie M. Coating solution for high-voltage cathode: AlF₃ atomic layer deposition for freestanding LiCoO₂ electrodes with high energy density and excellent flexibility. ACS Appl Mater Interfaces. 2017;9(11):9614-9619.

[91] Xie M, Li B, Zhou Y. Free-standing high-voltage LiCoO₂/multi-wall carbon nanotube paper electrodes with extremely high areal mass loading for lithium ion batteries. J Mater Chem A. 2015;3(46):23180-23184.

[92] He J, Zhang Y, Zhang Y, et al. Layered over-lithiated oxide coating for reviving spent LiCoO₂ cathode for stable high-voltage lithium-ion battery. J Alloys Compd. 2022;908:164576.

[93] Park J-H, Kim J-S, Shim E-G, et al. Polyimide gel polymer electrolyte-nanoencapsulated LiCoO₂ cathode materials for high-voltage Li-ion batteries. Electrochem Commun. 2010;12(8):1099.

[94] Lee E-H, Park J-H, Kim J-M, Lee S-Y. Direct surface modification of high-voltage LiCoO₂ cathodes by UV-cured nanothickness poly(ethylene glycol diacrylate) gel polymer electrolytes. Electrochim Acta. 2013;104:249.

[95] Fan T, Wang Y, Harika VK, et al. Highly stable 4.6 V LiCoO₂ cathodes for rechargeable Li batteries by rubidium-based surface modifications. Adv Sci. 2022;9(33):2202627.

[96] Zhu C, Liu J, Yu X, et al. Novel fabrication of Li₄Ti₅O₁₂ coated LiMN₂O₄ nanorods as cathode materials with long-term cyclic stability at high ambient temperature. Int J Electrochem Sci. 2019;14(8):7673.

[97] Liu Y, Zheng S, Wang Q, et al. Improvement the electrochemical performance of Cr doped layered-spinel composite cathode material Li_1.1Ni_0.235MN_0.735Cr_0.03O_2.3 with Li₄Ti₅O₁₂ coating. Ceram Int. 2017;43(12):8800.

[98] Ji Y, Yang D, Pan Y, et al. Directly-regenerated LiCoO₂ with a superb cycling stability at 4.6 V. Energy Storage Mater. 2023;60:102801.

[99] Zhang M, Wang L, Xu H, Song Y, He X. Polyimides as promising materials for lithium-ion batteries: a review. Nanomicro Lett. 2023;15(1):135.

[100] Park J-H, Cho J-H, Kim S-B, Kim W-S, Lee S-Y, Lee S-Y. A novel ion-conductive protection skin based on polyimide gel polymer electrolyte: application to nanoscale coating layer of high voltage LiNi_1/3CO_1/3MN_1/3O₂ cathode materials for lithium-ion batteries. J Mater Chem. 2012;22(25):12574.

[101] Wang J, Lei X, Guo S, et al. Doping strategy in nickel-rich layered oxide cathode for lithium-ion battery. Renewables. 2023;1(3):316-340.

[102] Chen Y, Hu W, Zhou Q, Li H. Conflicting roles of Na-doped layered cathode material LiCoO₂ for Li-ion batteries. J Solid State Electrochem. 2021;25(10-11):2565-2569.

[103] Hasan F, Kim J, Song H, Sung JH, Kim J, Yoo HD. Effect of particle size and doping on the electrochemical characteristics of Ca-doped LiCoO₂ cathodes. J Electrochem Sci Technol. 2020;11(4):352.

[104] Bai H, Yuan K, Zhang C, et al. Advantageous surface engineering to boost single-crystal quaternary cathodes for high-energy-density lithium-ion batteries. Energy Storage Mater. 2023;61:102879.

[105] House RA, Maitra U, Perez-Osorio MA, et al. Superstructure control of first-cycle voltage hysteresis in oxygen-redox cathodes. Nature. 2020;577(7791):502-508.

[106] Kim UH, Jun DW, Park KJ, et al. Pushing the limit of layered transition metal oxide cathodes for high-energy density rechargeable Li ion batteries. Energy Environ Sci. 2018;11(5):1271-1279.

[107] Kim J-M, Zhang X, Zhang J-G, Manthiram A, Meng YS, Xu W. A review on the stability and surface modification of layered transition-metal oxide cathodes. Mater Today. 2021;46:155-182.

[108] Wang T, Yang J, Wang H, et al. Promoting reversibility of Co-free layered cathodes by Al and cation vacancy. Adv Energy Mater. 2023;13(12):2204241.

[109] Sun C, Liao X, Xia F, et al. High-voltage cycling induced thermal vulnerability in LiCoO₂ cathode: cation loss and oxygen release driven by oxygen vacancy migration. ACS Nano. 2020;14(5):6181-6190.

[110] Li B, Liu W, Zhu J, et al. Anion doping in LiCoO₂ cathode materials for Li-ion batteries: a first-principles study. J Solid State Electrochem. 2022;26(12):2743-2748.

[111] Xia J, Zhang N, Yang Y, et al. Lanthanide contraction builds better high-voltage LiCoO₂ batteries. Adv Funct Mater. 2022;33(8):2212869.

[112] Reddy MV, Jie TW, Jafta CJ, et al. Studies on bare and Mg-doped LiCoO₂ as a cathode material for lithium ion batteries. Electrochim Acta. 2014;128:192-197.

[113] Shim J-H, Lee J, Han SY, Lee S. Synergistic effects of coating and doping for lithium ion battery cathode materials: synthesis and characterization of lithium titanate-coated LiCoO₂ with Mg doping. Electrochim Acta. 2015;186:201-208.

[114] Tang Y, Zhao J, Zhu H, et al. Towards extreme fast charging of 4.6 V LiCoO₂ via mitigating high-voltage kinetic hindrance. J Energy Chem. 2023;78:13-20.

[115] Qin N, Gan Q, Zhuang Z, et al. Hierarchical doping engineering with active/inert dual elements stabilizes LiCoO₂ to 4.6 V. Adv Energy Mater. 2022;12(31):2201549.

[116] Oh P, Yun J, Choi JH, et al. New ion substitution method to enhance electrochemical reversibility of Co-rich layered materials for Li-ion batteries. Adv Energy Mater. 2022;13(1):2202237.

[117] Xu L, Wang K, Gu F, Li T, Wang Z. Determining the intrinsic role of Mg doping in LiCoO₂. Mater Lett. 2020;277:128407.

[118] Zhang J-N, Li Q, Ouyang C, et al. Trace doping of multiple elements enables stable battery cycling of LiCoO₂ at 4.6 V. Nat Energy. 2019;4(7):594.

[119] Kong W, Zhou D, Zhang Q, et al. Adjusting the redox coupling effect via Li/Co anti-site defect for stable high-voltage LiCoO₂ cathode. Adv Funct Mater. 2022;33(8):2211033.

[120] Wang Y, Cheng T, Yu Z-E, Lyu Y, Guo B. Study on the effect of Ni and Mn doping on the structural evolution of LiCoO₂ under 4.6 V high-voltage cycling. J Alloys Compd. 2020;842:155827.

[121] Zhang H, Zhou Q, Cao F, et al. Understanding the role of Co in the Ni-rich cathode materials for Li-ion batteries. Ionics. 2022;28(12):5415.

[122] Zhu M, Huang Y, Chen G, et al. Sn, S co-doped LiCoO₂ with low lithium ion diffusion energy barrier and high passivation surface for fast charging lithium ion batteries. Chem Eng J. 2023;468:143585.

[123] Zhang X, Ren K, Liu Y, et al. Progress on entropy production engineering for electrochemical catalysis. Acta Phys Chim Sin. 2024;40(7):2307057.

[124] Tan X, Zhang Y, Xu S, et al. High-entropy surface complex stabilized LiCoO₂ cathode. Adv Energy Mater. 2023;13(24):2300147.

[125] Zhang R, Wang C, Zou P, et al. Long-life lithium-ion batteries realized by low-Ni, Co-free cathode chemistry. Nat Energy. 2023;8(7):695-702.

[126] Gu Z-Y, Guo J-Z, Cao J-M, et al. An advanced high-entropy fluorophosphate cathode for sodium-ion batteries with increased working voltage and energy density. Adv Mater. 2022;34(14):2110108.

[127] Wang YY, Liang Z, Liu ZC, et al. Synergy of epitaxial layer and bulk doping enables structural rigidity of cobalt-free ultrahigh-nickel oxide cathode for lithium-ion batteries. Adv Funct Mater. 2023;33(52):2308152.

[128] Xie M, Hu T, Yang L, Zhou Y. Synthesis of high-voltage (4.7 V) LiCoO₂ cathode materials with Al doping and conformal Al₂O₃ coating by atomic layer deposition. RSC Adv. 2016;6(68):63250-63255.

[129] Dong W, Ye B, Cai M, et al. Superwettable high-voltage LiCoO₂ for low-temperature lithium ion batteries. ACS Energy Lett. 2023;8(2):881-888.

[130] Zhong J, Zhao W, Zhang M, et al. LiMgPO₄-coating-induced phosphate shell and bulk Mg-doping enables stable ultra-high-voltage cycling of LiCoO₂ cathode. Small. 2023;19(39):2300802.

[131] Hasan F, Abdelazeez AAA, Rabia M, Yoo HD. Divalent ion pillaring and coating on lithium cobalt oxide cathode for fast intercalation of Li⁺ ion with high capacity. Energy Technol. 2023;11(7):2300153.

[132] Tan X, Mao D, Zhao T, et al. Long-term highly stable high-voltage LiCoO₂ synthesized via a solid sulfur-assisted one-pot approach. Small. 2022;18(26):2202143.

[133] Liu X, Fu A, Lin J, et al. Constructing a stabilized cathode electrolyte interphase for high-voltage LiCoO₂ batteries via the phenylmaleic anhydride additive. ACS Appl Energy Mater. 2023;6(3):2001-2009.

[134] Zou Y, Cheng Y, Lin J, et al. Boosting high voltage cycling of LiCoO₂ cathode via triisopropanolamine cyclic borate electrolyte additive. J Power Sources. 2022;532:231372.

[135] Chen H, Wen Y, Wang Y, et al. Direct surface coating of high voltage LiCoO₂ cathode with P(VDF-HFP) based gel polymer electrolyte. RSC Adv. 2020;10(41):24533-24541.

[136] Lu ZX, Mu KW, Zhang ZY, et al. A porous current collector cleaner enables thin cathode electrolyte interphase on LiCoO₂ for stable high-voltage cycling. J Mater Chem A. 2021;9(47):26989-26998.

[137] Tang Q, Dai X, Wang Z, et al. Enhanced high-voltage performance of LiCoO₂ cathode by directly coating of the electrode with Li₂CO₃ via a wet chemical method. Ceram Int. 2021;47(14):19374-19383.

[138] Zhang J, Gao R, Sun L, Zhang H, Hu Z, Liu X. Unraveling the multiple effects of Li₂ZrO₃ coating on the structural and electrochemical performances of LiCoO₂ as high-voltage cathode materials. Electrochim Acta. 2016;209:102-110.

[139] Zhu D, Wang C, Zou P, et al. Deep-learning aided atomic-scale phase segmentation toward diagnosing complex oxide cathodes for lithium-ion batteries. Nano Lett. 2023;23(17):8272-8279.

[140] Wang C, Wang X, Zhang R, Lei T, Kisslinger K, Xin HL. Resolving complex intralayer transition motifs in high-Ni-content layered cathode materials for lithium-ion batteries. Nat Mater. 2023;22(2):235-241.

[141] Wang D, Ma X, Wang Y, et al. Shape control of CoO and LiCoO₂ nanocrystals. Nano Res. 2010;3(1):1-7.

[142] Xiao X, Liu X, Wang L, et al. LiCoO₂ nanoplates with exposed (001) planes and high rate capability for lithium-ion batteries. Nano Res. 2012;5(6):395-401.

[143] Xiao X, Wang L, Li J, et al. Rational synthesis of high-performance Ni-rich layered oxide cathode enabled via probing solid-state lithiation evolution. Nano Energy. 2023;113:108528.

[144] Wang G, Fearn T, Wang T, Choy K-L. Insight gained from using machine learning techniques to predict the discharge capacities of doped spinel cathode materials for lithium-ion batteries applications. Energy Technol. 2021;9(5):2100053.

[145] Sheng L, Wang Q, Liu X, et al. Suppressing electrolyte-lithium metal reactivity via Li⁺-desolvation in uniform nano-porous separator. Nat Commun. 2022;13(1):172.

[146] Huang H, Li Z, Gu S, et al. Dextran sulfate lithium as versatile binder to stabilize high-voltage LiCoO₂ to 4.6 V. Adv Energy Mater. 2021;11(44):2101864.

[147] Xu G, Luo L, Liang J, et al. Origin of high electrochemical stability of multi-metal chloride solid electrolytes for high energy all-solid-state lithium-ion batteries. Nano Energy. 2022;92:106674.

RIGHTS & PERMISSIONS

2024 The Authors. Electron published by Harbin Institute of Technology and John Wiley & Sons Australia, Ltd.