Intraparticular Heterogeneity Limits Capacity in Lithium–Sulfur Batteries With Carbonate Electrolyte

Abstract

The formation of a stable cathode-electrolyte interphase (CEI) is critical for the performance of lithium–sulfur (Li–S) batteries with carbonate-based electrolytes, as it suppresses parasitic polysulfide reactions and enables solid-state sulfur conversion. In nanoporous carbon hosts, the CEI together with nanopore confinement plays a key role in capacity retention and long-term cycling. Yet, its spatial formation, stability, and contribution to electrochemical performance remain poorly understood, partly due to challenges in characterization caused by beam and air sensitivity. Here, we employ cryogenic transmission electron microscopy (cryo-TEM) with electron energy loss spectroscopy and energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and electrochemical testing together with galvanostatic intermittent titration technique measurements to elucidate how carbon particle size affects CEI formation and electrochemical performance. We find that the CEI is not a uniform surface film but extends heterogeneously into the particle bulk. Mass transport during the first discharge dictates CEI development, and larger particles suffer from inactive regions due to the preferential CEI formation only in the outer regions of the particles. During extended cycling, charge transfer resistance at confined CEI/active material/carbon interfaces emerges as the dominant performance-limiting factor. These findings show that particle size controls CEI formation during initial discharge, offering guidance for designing carbon hosts from nano- to micrometer length scales in Li–S battery cathodes.

Keywords

carbon particle size / CEI formation / cryogenic electron microscopy / electrochemical performance / intraparticular heterogeneity / lithium–sulfur batteries / nanoporous carbons / solid-state sulfur conversion

References

[1] X. Chen, H. Ji, Z. Rao, et al., “Insight Into the Fading Mechanism of the Solid-Conversion Sulfur Cathodes and Designing Long Cycle Lithium–Sulfur Batteries,” Advanced Energy Materials 12, no. 1 (2021): 2102774, https://doi.org/10.1002/aenm.202102774.

[2] X. Chen, L. Yuan, Z. Li, et al., “Realizing an Applicable “Solid → Solid” Cathode Process via a Transplantable Solid Electrolyte Interface for Lithium–Sulfur Batteries,” ACS Applied Materials & Interfaces 11, no. 33 (2019): 29830–29837, https://doi.org/10.1021/acsami.9b07787.

[3] L. Wang, Y. Ye, N. Chen, et al., “Development and Challenges of Functional Electrolytes for High-Performance Lithium–Sulfur Batteries,” Advanced Functional Materials 28, no. 38 (2018): 1800919, https://doi.org/10.1002/adfm.201800919.

[4] G. Li, S. Wang, Y. Zhang, M. Li, Z. Chen, and J. Lu, “Revisiting the Role of Polysulfides in Lithium–Sulfur Batteries,” Advanced Materials 30, no. 22 (2018): e1705590, https://doi.org/10.1002/adma.201705590.

[5] J. Liu, H. Chen, W. Chen, Y. Zhang, and Y. Zheng, “New Insight Into the ‘Shuttle Mechanism’ of Rechargeable Lithium–Sulfur Batteries,” ChemElectroChem 6, no. 10 (2019): 2782–2787, https://doi.org/10.1002/celc.201900420.

[6] A. Rosenman, E. Markevich, G. Salitra, Y. Talyosef, F. Chesneau, and D. Aurbach, “Facile Synthesis and Very Stable Cycling of Polyvinylidene Dichloride Derived Carbon: Sulfur Composite Cathode,” Journal of the Electrochemical Society 163, no. 9 (2016): A1829–A1835, https://doi.org/10.1149/2.0151609jes.

[7] E. Markevich, G. Salitra, A. Rosenman, Y. Talyosef, F. Chesneau, and D. Aurbach, “The Effect of a Solid Electrolyte Interphase on the Mechanism of Operation of Lithium–Sulfur Batteries,” Journal of Materials Chemistry A 3, no. 39 (2015): 19873–19883, https://doi.org/10.1039/c5ta04613k.

[8] X. Ji, K. T. Lee, and L. F. Nazar, “A Highly Ordered Nanostructured Carbon–Sulphur Cathode for Lithium–Sulphur Batteries,” Nature Materials 8, no. 6 (2009): 500–506, https://doi.org/10.1038/nmat2460.

[9] J. Li, L. Gao, F. Pan, et al., “Engineering Strategies for Suppressing the Shuttle Effect in Lithium–Sulfur Batteries,” Nano-Micro Letters 16, no. 1 (2023): 12, https://doi.org/10.1007/s40820-023-01223-1.

[10] W. P. Wang, J. Zhang, J. Chou, et al., “Solidifying Cathode–Electrolyte Interface for Lithium–Sulfur Batteries,” Advanced Energy Materials 11, no. 2 (2020): 2000791, https://doi.org/10.1002/aenm.202000791.

[11] L. Wang, Y. Lin, S. DeCarlo, et al., “Compositions and Formation Mechanisms of Solid-Electrolyte Interphase on Microporous Carbon/Sulfur Cathodes,” Chemistry of Materials 32, no. 9 (2020): 3765–3775, https://doi.org/10.1021/acs.chemmater.9b05027.

[12] E. Markevich, G. Salitra, Y. Talyosef, F. Chesneau, and D. Aurbach, “Review—On the Mechanism of Quasi-Solid-State Lithiation of Sulfur Encapsulated in Microporous Carbons: Is the Existence of Small Sulfur Molecules Necessary?,” Journal of the Electrochemical Society 164, no. 1 (2016): A6244–A6253, https://doi.org/10.1149/2.0391701jes.

[13] B. Zhang, X. Qin, G. R. Li, and X. P. Gao, “Enhancement of Long Stability of Sulfur Cathode by Encapsulating Sulfur Into Micropores of Carbon Spheres,” Energy & Environmental Science 3, no. 10 (2010): 1531–1537, https://doi.org/10.1039/c002639e.

[14] Z. Li, L. Yuan, Z. Yi, et al., “Insight Into the Electrode Mechanism in Lithium–Sulfur Batteries With Ordered Microporous Carbon Confined Sulfur as the Cathode,” Advanced Energy Materials 4, no. 7 (2013): 1301473, https://doi.org/10.1002/aenm.201301473.

[15] M. Liu, L. J. Hu, Z. K. Guan, et al., “Tailoring Cathode-Electrolyte Interface for High-Power and Stable Lithium–Sulfur Batteries,” Nano-Micro Letters 17, no. 1 (2024): 85, https://doi.org/10.1007/s40820-024-01573-4.

[16] I. Sungjemmenla, V. S. K., C. B. Soni, V. Kumar, and Z. W. Seh, “Understanding the Cathode–Electrolyte Interphase in Lithium-Ion Batteries,” Energy Technology 10, no. 9 (2022): 2200421, https://doi.org/10.1002/ente.202200421.

[17] J. Gao, M. A. Lowe, Y. Kiya, and H. D. Abruña, “Effects of Liquid Electrolytes on the Charge–Discharge Performance of Rechargeable Lithium/Sulfur Batteries: Electrochemical and In-Situ X-Ray Absorption Spectroscopic Studies,” Journal of Physical Chemistry C 115, no. 50 (2011): 25132–25137, https://doi.org/10.1021/jp207714c.

[18] F. He, X. Wu, J. Qian, et al., “Building a Cycle-Stable Sulphur Cathode by Tailoring Its Redox Reaction Into a Solid-Phase Conversion Mechanism,” Journal of Materials Chemistry A 6, no. 46 (2018): 23396–23407, https://doi.org/10.1039/c8ta08159j.

[19] T. Yim, M.-S. Park, J.-S. Yu, et al., “Effect of Chemical Reactivity of Polysulfide Toward Carbonate-Based Electrolyte on the Electrochemical Performance of Li–S Batteries,” Electrochimica Acta 107 (2013): 454–460, https://doi.org/10.1016/j.electacta.2013.06.039.

[20] Z. Shen, W. Zhang, S. Mao, S. Li, X. Wang, and Y. Lu, “Tailored Electrolytes Enabling Practical Lithium–Sulfur Full Batteries via Interfacial Protection,” ACS Energy Letters 6, no. 8 (2021): 2673–2681, https://doi.org/10.1021/acsenergylett.1c01091.

[21] J. T. Lee, K. Eom, F. Wu, et al., “Enhancing the Stability of Sulfur Cathodes in Li–S Cells via In Situ Formation of a Solid Electrolyte Layer,” ACS Energy Letters 1, no. 2 (2016): 373–379, https://doi.org/10.1021/acsenergylett.6b00163.

[22] F. Huang, L. Gao, Y. Zou, et al., “Akin Solid–Solid Biphasic Conversion of a Li–S Battery Achieved by Coordinated Carbonate Electrolytes,” Journal of Materials Chemistry A 7, no. 20 (2019): 12498–12506, https://doi.org/10.1039/c9ta02877c.

[23] C. Li, Y. Li, Y. Fan, et al., “Mapping Techniques for the Design of Lithium-Sulfur Batteries,” Small 18, no. 14 (2022): e2106657, https://doi.org/10.1002/smll.202106657.

[24] G. Yang, R. Tao, C. J. Jafta, et al., “Investigating Multiscale Spatial Distribution of Sulfur in a CNT Scaffold and Its Impact on Li–S Cell Performance,” Journal of Physical Chemistry C 125, no. 24 (2021): 13146–13157, https://doi.org/10.1021/acs.jpcc.1c02288.

[25] G. Zhou, D.-W. Wang, F. Li, et al., “A Flexible Nanostructured Sulphur–Carbon Nanotube Cathode With High Rate Performance for Li-S Batteries,” Energy & Environmental Science 5, no. 10 (2012): 8901–8906, https://doi.org/10.1039/c2ee22294a.

[26] J. Zhang, Z. Dong, X. Wang, et al., “Sulfur Nanocrystals Anchored Graphene Composite With Highly Improved Electrochemical Performance for Lithium–Sulfur Batteries,” Journal of Power Sources 270 (2014): 1–8, https://doi.org/10.1016/j.jpowsour.2014.07.089.

[27] G. Hu, Z. Sun, C. Shi, et al., “A Sulfur-Rich Copolymer@Cnt Hybrid Cathode With Dual-Confinement of Polysulfides for High-Performance Lithium–Sulfur Batteries,” Advanced Materials 29, no. 11 (2016): 1603835, https://doi.org/10.1002/adma.201603835.

[28] A. Senol Gungor, J. M. von Mentlen, J. G. A. Ruthes, et al., “Understanding Rate and Capacity Limitations in Li-S Batteries Based on Solid-State Sulfur Conversion in Confinement,” ACS Applied Materials & Interfaces 16, no. 49 (2024): 67651–67661, https://doi.org/10.1021/acsami.4c13183.

[29] F. J. García-Soriano, F. Cometto, S. Raviolo, et al., “Biocarbon From Olive Pomace Residue as a Sulfur Host for Carbonate-Based Lithium-Sulfur Batteries,” Communications Materials 6, no. 1 (2025): 122, https://doi.org/10.1038/s43246-025-00846-8.

[30] S. Haber and M. Leskes, “What Can We Learn From Solid State NMR on the Electrode-Electrolyte Interface?,” Advanced Materials 30, no. 41 (2018): e1706496, https://doi.org/10.1002/adma.201706496.

[31] Y. Chen, Q. He, Y. Mo, et al., “Engineering an Insoluble Cathode Electrolyte Interphase Enabling High Performance NCM811//Graphite Pouch Cell at 60°C,” Advanced Energy Materials 12, no. 33 (2022): 2201631, https://doi.org/10.1002/aenm.202201631.

[32] D. Cheng, B. Lu, G. Raghavendran, M. Zhang, and Y. S. Meng, “Leveraging Cryogenic Electron Microscopy for Advancing Battery Design,” Matter 5, no. 1 (2022): 26–42, https://doi.org/10.1016/j.matt.2021.11.019.

[33] K. Liang, X. Yuan, X. Chen, et al., “A Beginner's Guide to Cryo-Em for Battery Research,” Nano Letters 25, no. 18 (2025): 7210–7223, https://doi.org/10.1021/acs.nanolett.5c00740.

[34] X. C. Ren, X. Q. Zhang, R. Xu, J. Q. Huang, and Q. Zhang, “Analyzing Energy Materials by Cryogenic Electron Microscopy,” Advanced Materials 32, no. 24 (2020): e1908293, https://doi.org/10.1002/adma.201908293.

[35] Z. Zhang, J. Yang, W. Huang, et al., “Cathode-Electrolyte Interphase in Lithium Batteries Revealed by Cryogenic Electron Microscopy,” Matter 4, no. 1 (2021): 302–312, https://doi.org/10.1016/j.matt.2020.10.021.

[36] X. Xing, Y. Li, X. Wang, V. Petrova, H. Liu, and P. Liu, “Cathode Electrolyte Interface Enabling Stable Li–S Batteries,” Energy Storage Materials 21 (2019): 474–480, https://doi.org/10.1016/j.ensm.2019.06.022.

[37] W. Huang, D. T. Boyle, Y. Li, et al., “Nanostructural and Electrochemical Evolution of the Solid-Electrolyte Interphase on Cuo Nanowires Revealed by Cryogenic-Electron Microscopy and Impedance Spectroscopy,” ACS Nano 13, no. 1 (2019): 737–744, https://doi.org/10.1021/acsnano.8b08012.

[38] B. Han, Z. Zhang, Y. Zou, et al., “Poor Stability of Li₂Co₃ in the Solid Electrolyte Interphase of a Lithium-Metal Anode Revealed by Cryo-Electron Microscopy,” Advanced Materials 33, no. 22 (2021): e2100404, https://doi.org/10.1002/adma.202100404.

[39] M. J. Zachman, Z. Tu, S. Choudhury, L. A. Archer, and L. F. Kourkoutis, “Cryo-Stem Mapping of Solid-Liquid Interfaces and Dendrites in Lithium-Metal Batteries,” Nature 560, no. 7718 (2018): 345–349, https://doi.org/10.1038/s41586-018-0397-3.

[40] W. Huang, H. Wang, D. T. Boyle, Y. Li, and Y. Cui, “Resolving Nanoscopic and Mesoscopic Heterogeneity of Fluorinated Species in Battery Solid-Electrolyte Interphases by Cryogenic Electron Microscopy,” ACS Energy Letters 5, no. 4 (2020): 1128–1135, https://doi.org/10.1021/acsenergylett.0c00194.

[41] Y. Li, Y. Li, A. Pei, et al., “Atomic Structure of Sensitive Battery Materials and Interfaces Revealed by Cryo–Electron Microscopy,” Science 358, no. 6362 (2017): 506–510.

[42] C. X. Bi, N. Yao, X. Y. Li, et al., “Unveiling the Reaction Mystery Between Lithium Polysulfides and Lithium Metal Anode in Lithium-Sulfur Batteries,” Advanced Materials 36, no. 41 (2024): e2411197, https://doi.org/10.1002/adma.202411197.

[43] X. Wang, Y. Li, and Y. S. Meng, “Cryogenic Electron Microscopy for Characterizing and Diagnosing Batteries,” Joule 2, no. 11 (2018): 2225–2234, https://doi.org/10.1016/j.joule.2018.10.005.

[44] J. Conder, C. Marino, P. Novák, and C. Villevieille, “Do Imaging Techniques Add Real Value to the Development of Better Post-Li-Ion Batteries?,” Journal of Materials Chemistry A 6, no. 8 (2018): 3304–3327, https://doi.org/10.1039/c7ta10622j.

[45] S. Zhou, J. Shi, S. Liu, et al., “Visualizing Interfacial Collective Reaction Behaviour of Li-S Batteries,” Nature 621, no. 7977 (2023): 75–81, https://doi.org/10.1038/s41586-023-06326-8.

[46] Z. Ju, H. Yuan, O. Sheng, et al., “Cryo-Electron Microscopy for Unveiling the Sensitive Battery Materials,” Small Science 1, no. 11 (2021): 2100055, https://doi.org/10.1002/smsc.202100055.

[47] D. B. Nash, “Sulfur in Vacuum: Sublimation Effects on Frozen Melts, and Applications to Io's Surface and Torus,” Icarus 72 (1987): 1–34.

[48] C. Raiß, K. Peppler, J. Janek, and P. Adelhelm, “Pitfalls in the Characterization of Sulfur/Carbon Nanocomposite Materials for Lithium–Sulfur Batteries,” Carbon 79 (2014): 245–255, https://doi.org/10.1016/j.carbon.2014.07.065.

[49] B. D. A. Levin, M. J. Zachman, J. G. Werner, et al., “Characterization of Sulfur and Nanostructured Sulfur Battery Cathodes in Electron Microscopy Without Sublimation Artifacts,” Microscopy and Microanalysis 23, no. 1 (2017): 155–162, https://doi.org/10.1017/S1431927617000058.

[50] K. Liao and A. Manthiram, “Impact of Cathode Microstructure on Sulfur Redox Kinetics in Lithium–Sulfur Batteries,” Advanced Energy Materials 15 (2025): 2502062, https://doi.org/10.1002/aenm.202502062.

[51] Z. X. Chen, Q. Cheng, X. Y. Li, et al., “Cathode Kinetics Evaluation in Lean-Electrolyte Lithium-Sulfur Batteries,” Journal of the American Chemical Society 145, no. 30 (2023): 16449–16457, https://doi.org/10.1021/jacs.3c02786.

[52] X. Ji and L. F. Nazar, “Advances in Li–S Batteries,” Journal of Materials Chemistry 20, no. 44 (2010): 9821, https://doi.org/10.1039/b925751a.

[53] M. L. Para, C. A. Calderón, S. Drvarič Talian, et al., “Extending the Conversion Rate of Sulfur Infiltrated Into Microporous Carbon in Carbonate Electrolytes,” Batteries & Supercaps 5, no. 5 (2022): e202100374, https://doi.org/10.1002/batt.202100374.

[54] T. Li, X.-Q. Zhang, P. Shi, and Q. Zhang, “Fluorinated Solid-Electrolyte Interphase in High-Voltage Lithium Metal Batteries,” Joule 3, no. 11 (2019): 2647–2661, https://doi.org/10.1016/j.joule.2019.09.022.

[55] J. M. von Mentlen, A. S. Güngör, T. Demuth, et al., “Unraveling Multiphase Conversion Pathways in Lithium-Sulfur Batteries Through Cryo Transmission Electron Microscopy and Machine Learning-Assisted Operando Neutron Scattering,” ACS Nano 19, no. 17 (2025): 16626–16638, https://doi.org/10.1021/acsnano.5c00536.

[56] X. Q. Zhang, T. Li, B. Q. Li, et al., “A Sustainable Solid Electrolyte Interphase for High-Energy-Density Lithium Metal Batteries Under Practical Conditions,” Angewandte Chemie International Edition 59, no. 8 (2020): 3252–3257, https://doi.org/10.1002/anie.201911724.

[57] A. Vizintin, M. Lozinšek, R. K. Chellappan, et al., “Fluorinated Reduced Graphene Oxide as an Interlayer in Li–S Batteries,” Chemistry of Materials 27, no. 20 (2015): 7070–7081, https://doi.org/10.1021/acs.chemmater.5b02906.

[58] D. J. Tarimo, F. J. García-Soriano, A. Vizintin, C. Prehal, and V. Presser, “Performance of Microporous Carbon Cathodes and Impact of Cathode/Solid Electrolyte Interphase Formation Using Carbonate and Ether-Based Electrolytes in Lithium–Sulfur Batteries,” ACS Applied Energy Materials 8, no. 16 (2025): 12139–12156, https://doi.org/10.1021/acsaem.5c01629.

[59] Y. Zhong, K. R. Yang, W. Liu, P. He, V. Batista, and H. Wang, “Mechanistic Insights Into Surface Chemical Interactions Between Lithium Polysulfides and Transition Metal Oxides,” Journal of Physical Chemistry C 121, no. 26 (2017): 14222–14227, https://doi.org/10.1021/acs.jpcc.7b04170.

[60] F. J. García-Soriano, S. A. Ceppi, F. P. Cometto, et al., “Sepiolite as a Novel Polysulfide Trapper for Energy Applications: An Electrochemical, X-Ray Spectroscopic and DFT Study,” Physical Chemistry Chemical Physics 25, no. 36 (2023): 24761–24769, https://doi.org/10.1039/d3cp03157h.

[61] Y. Wang, Y. Liu, Y. Tu, and Q. Wang, “Reductive Decomposition of Solvents and Additives Toward Solid-Electrolyte Interphase Formation in Lithium-Ion Battery,” Journal of Physical Chemistry C 124, no. 17 (2020): 9099–9108, https://doi.org/10.1021/acs.jpcc.9b10535.

[62] C. Xu, F. Lindgren, B. Philippe, et al., “Improved Performance of the Silicon Anode for Li-Ion Batteries: Understanding the Surface Modification Mechanism of Fluoroethylene Carbonate as an Effective Electrolyte Additive,” Chemistry of Materials 27, no. 7 (2015): 2591–2599, https://doi.org/10.1021/acs.chemmater.5b00339.

[63] H. Kim, F. Wu, J. T. Lee, et al., “In Situ Formation of Protective Coatings on Sulfur Cathodes in Lithium Batteries With Lifsi-Based Organic Electrolytes,” Advanced Energy Materials 5, no. 6 (2014): 1401792, https://doi.org/10.1002/aenm.201401792.

[64] J. Tan, J. Matz, P. Dong, J. Shen, and M. Ye, “A Growing Appreciation for the Role of Lif in the Solid Electrolyte Interphase,” Advanced Energy Materials 11, no. 16 (2021): 2100046, https://doi.org/10.1002/aenm.202100046.

[65] S. Lorger, K. Narita, R. Usiskin, and J. Maier, “Enhanced Ion Transport in Li₂O and Li₂S Films,” Chemical Communications 57, no. 53 (2021): 6503–6506, https://doi.org/10.1039/d1cc00557j.

[66] D. Wang, B. Gwalani, D. Wierzbicki, et al., “Overcoming the Conversion Reaction Limitation at Three-Phase Interfaces Using Mixed Conductors Towards Energy-Dense Solid-State Li-S Batteries,” Nature Materials 24, no. 2 (2025): 243–251, https://doi.org/10.1038/s41563-024-02057-x.

[67] C. Wang, K. Adair, and X. Sun, “All-Solid-State Lithium Metal Batteries With Sulfide Electrolytes: Understanding Interfacial Ion and Electron Transport,” Accounts of Materials Research 3, no. 1 (2021): 21–32, https://doi.org/10.1021/accountsmr.1c00137.

[68] X. Zhu, L. Wang, Z. Bai, J. Lu, and T. Wu, “Sulfide-Based All-Solid-State Lithium-Sulfur Batteries: Challenges and Perspectives,” Nano-Micro Letters 15, no. 1 (2023): 75, https://doi.org/10.1007/s40820-023-01053-1.

[69] F. Y. Fan, W. C. Carter, and Y. M. Chiang, “Mechanism and Kinetics of Li₂S Precipitation in Lithium-Sulfur Batteries,” Advanced Materials 27, no. 35 (2015): 5203–5209, https://doi.org/10.1002/adma.201501559.

[70] H. Yuan, H. J. Peng, J. Q. Huang, and Q. Zhang, “Sulfur Redox Reactions at Working Interfaces in Lithium–Sulfur Batteries: A Perspective,” Advanced Materials Interfaces 6, no. 4 (2019): 1802046, https://doi.org/10.1002/admi.201802046.

[71] Y. Shin, D. Stepien, M. Hepp, B. Butz, D. Bresser, and S. Fleischmann, “Cryogenic Electron Microscopy Workflows for the Characterization of Electrochemical Interfaces and Interphases in Batteries,” Journal of Power Sources 556 (2023): 232515, https://doi.org/10.1016/j.jpowsour.2022.232515.

RIGHTS & PERMISSIONS

2026 The Author(s). Battery Energy published by Xijing University and John Wiley & Sons Australia, Ltd.