On the preload attenuation of PTFE bolted joints under temperature loads

Abstract

Polytetrafluoroethylene (PTFE)-bolted joints are commonly used in equipment, apparatuses, and devices in various industries, including the semiconductors, chemical, biomedicine, food, and pharmaceutical industries. However, owing to their significant viscoelasticity, these joints are prone to preload attenuation during service, which significantly compromises the joint reliability. This study aimed to elucidate the preload attenuation behavior of PTFE bolts and the effects of environmental temperature, initial tightening torque, and bolt geometry on this attenuation. A thermo-viscoelastic constitutive model for PTFE was developed based on material relaxation test data, followed by the construction of a finite element model for the PTFE bolted joints. The simulation and experimental results over 24 h indicated that approximately 90% of the total preload attenuation occurred within the first hour of loading. The model achieved a mean absolute percentage error of less than 15% compared with the experimental results under various environmental temperatures, initial tightening torques, nominal bolt diameters, and cyclic temperature loadings. Using this model, the factors influencing the PTFE bolt preload attenuation were investigated, and a sensitivity analysis was conducted. The findings indicate that the environmental temperature has the greatest influence on preload attenuation, followed by the initial tightening torque and bolt nominal diameter, whereas the bolt effective length has little impact.

Keywords

Polytetrafluoroethylene (PTFE) / Bolted joints / Thermo-viscoelasticity / Preload attenuation

References

[1] Deshwal D, Belgamwar SU, Bekinal SI, et al.. Role of reinforcement on the tribological properties of polytetrafluoroethylene composites: a comprehensive review. Polym Compos, 2024, 45(16): 14475-14497

[2] Sreenilayam-Raveendran RK, Azarian MH, Morillo C, et al.. Comparative evaluation of metal and polymer ball bearings. Wear, 2013, 302(1/2): 1499-1505

[3] Shah V, Panchal T, Bharatiya B, et al.. Colloidal PTFE dispersion in commercial engine oil: lubrication by pluronic adsorption at the interface. Colloids Surf, A, 2020, 597 Article ID: 124775

[4] Ebnesajjad S, Khaladkar PR (2004) Fluoropolymer applications in the chemical processing industries: the definitive users guide and databook. William Andrew

[5] Hong WP, Zhang H. Application of PTFE heat exchanger in low temperature waste heat of big coal-fired power plants. Appl Mech Mater, 2015, 789: 503-507

[6] Zhang Y, Xu S, Zhang Q, et al.. Experimental and theoretical research on the stress-relaxation behaviors of PTFE coated fabrics under different temperatures. Adv Mater Sci Eng, 2015, 1: 319473

[7] Tan B, Stephens LS. Evaluation of viscoelastic characteristics of PTFE-Based materials. Tribol Int, 2019, 140 Article ID: 105870

[8] Rae PJ, Brown EN. The properties of poly (tetrafluoroethylene)(PTFE) in tension. Polymer, 2005, 46(19): 8128-8140

[9] Zhao L, Qiao J, Zhang J, et al.. A generalized linear viscoelastic model of polytetrafluoroethylene from 4 K to 403 K. J Mater Eng Perform, 2025, 2025: 1-11

[10] Carvalho PRP, Coda HB, Sanches RAK. A large strain thermodynamically-based viscoelastic viscoplastic model with application to finite element analysis of polytetrafluoroethylene (PTFE). Eur Jo Mech A Solids, 2023, 97 Article ID: 104850

[11] Adibeig MR, Hassanifard S, Vakili-Tahami F. Optimum creep lifetime of polymethyl methacrylate (PMMA) tube using rheological creep constitutive models based on experimental data. Polym Test, 2019, 75: 107-116

[12] Gnip IY, Vaitkus S, Kerulis V, et al.. Analytical description of the creep of expanded polystyrene (EPS) under long-term compressive loading. Polym Test, 2011, 30(5): 493-500

[13] Williams ML, Landel RF, Ferry JD. The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids. J Am Chem Soc, 1955, 77(14): 3701-3707

[14] Zocher MA, Groves SE, Allen DH. A three-dimensional finite element formulation for thermoviscoelastic orthotropic media. Int J Numer Meth Eng, 1997, 40(12): 2267-2288

[15] Park SW, Schapery RA. Methods of interconversion between linear viscoelastic material functions. Part I—a numerical method based on prony series. Int J Solids Struct, 1999, 36(11): 1653-1675

[16] Nunes SG, Saseendran S, Joffe R, et al.. On temperature-related shift factors and master curves in viscoelastic constitutive models for thermoset polymers. Mech Compos Mater, 2020, 56(5): 573-590

[17] Xie Y, Xiao Y, Lv J, et al.. Influence of creep on preload relaxation of bolted composite joints: modeling and numerical simulation. Compos Struct, 2020, 245 Article ID: 112332

[18] Hu J, Jin J, Xuan S, et al.. Influence of cyclical hygrothermal aging on mechanical response and structural durability of composite bolted interference-fit joints. Thin Wall Struct, 2022, 173 Article ID: 108997

[19] Shahin A, Barsoum I, Korkees F. Analysis of a HDPE flanged connection with a time and temperature dependent constitutive behavior. Int J Press Vessels Pip, 2021, 191 Article ID: 104375

[20] Xu P, Zhou Z, Liu T, et al.. The investigation of viscoelastic mechanical behaviors of bolted GLARE joints: modeling and experiments. Int J Mech Sci, 2020, 175 Article ID: 105538

[21] Kanthabhabha JRP, Zhao Z, Bouzid AH. Creep-relaxation modeling of HDPE and polyvinyl chloride bolted flange joints. J Pressure Vessel Technol, 2020, 142(5): Article ID: 051303

[22] Ding G, Feng P, Wang Y, et al.. Long-term bolt preload relaxation and contact pressure distribution in clamping anchorages for CFRP plates. Compos Struct, 2024, 329 Article ID: 117780

[23] Jiang K, Liu Z, Zhang T, et al.. Influence of bolt creep induced pre-tightening force relaxation on dynamic response of the bolted joint system. J Sound Vib, 2025, 596 Article ID: 118800

[24] Wu X, Yuan B, Yang J, et al.. A modeling study on composite bolted connections for preload relaxation considering accelerated degradation. Compos Struct, 2025, 363 Article ID: 119070

[25] Ornaghi HLJr, Almeida JHSJr, Monticeli FM, et al.. Stress relaxation, creep, and recovery of carbon fiber non-crimp fabric composites. Compos Part C Open Access, 2020, 3 Article ID: 100051

[26] Fukuoka T, Nomura M. Proposition of helical thread modeling with accurate geometry and finite element analysis. J Pressure Vessel Technol, 2008, 130(1): Article ID: 011204

[27] Yang J, Wang S, Lu H, et al.. Non-stationary viscoelastic modeling of compression creep behavior in composite bolted joints. Polymers, 2025, 17(10): 1382

[28] Zhang X, Liu J, Xia H, et al.. Effects of curing, temperature, pressure, and moisture on the surface-figure of a high-precision bonded mirror. Precis Eng, 2024, 85: 205-216

[29] Plota A, Masek A. Lifetime prediction methods for degradable polymeric materials—a short review. Materials, 2020, 13(20): 4507

[30] Douglas-Smith D, Iwanaga T, Croke BFW, et al.. Certain trends in uncertainty and sensitivity analysis: an overview of software tools and techniques. Environ Model Softw, 2020, 124 Article ID: 104588

Funding

Beijing Natural Science Foundation(L248004)

National Natural Science Foundation of China(No. 52375480)

RIGHTS & PERMISSIONS

Shanghai University and Periodicals Agency of Shanghai University and Springer-Verlag GmbH Germany, part of Springer Nature