Data-driven optimization of frozen sand mold cryogenic cutting process parameters for cutting energy and tool wear reduction

Abstract

Green manufacturing prioritizes quality, efficiency, low energy consumption, and cleanliness in milling technology. Consequently, a data-driven optimization method was proposed for configuring multiple technological parameters in frozen sand molds, to reduce energy consumption and tool wear during processing. Initially, a power composition model for frozen sand mold processing was developed, based on an analysis of the relationship between the energy consumption and various actions during different processing states. Subsequently, using Archard wear theory, a discrete element model for cutting frozen sand molds was established to investigate the wear characteristics of flat-end milling tools influenced by multiple factors. The cutting wear of the frozen sand mold presents as a continuous abrasive wear form at polycrystalline diamond (PCD) cutting edge and the side end of the tool shank. Comprehensive experiments were conducted to develop a Kriging energy consumption model and radial basis function model for tool wear based on varying cutting technological parameters. The accuracy of the developed surrogate model was confirmed using an optimal Latin hypercube experimental design and leave-p-out cross-validation (LPOCV). Analysis of the technological parameters revealed that the milling speed and feed rate per tooth significantly affected both milling power and tool wear. Finally, the surrogate model was integrated with particle swarm optimization and a genetic algorithm to solve for the Pareto frontier and identify the optimal combination of cutting parameters. The optimized parameters of the multi-objective model reduced the milling power by 29.88% and tool wear by 18.18% during the processing of frozen sand molds. The models proposed for the milling power and tool wear in this study are accurate and reliable. By revealing the mapping relationship among the cutting power, tool wear and various cutting parameters, the proposed model can serve as an excellent platform for the energy-saving manufacturing of frozen sand molds.

Keywords

Frozen sand mold / Data-driven / Cutting energy consumption / Tool wear / Multi-objective optimization

References

[1] ShanZ, LiuF, SunQGreen manufacturing processes and equipment, 2022, Beijing. China Machine Press.

[2] SivarupanT, BalasubramaniN, SaxenaP, et al.. A review on the progress and challenges of binder jet 3D printing of sand moulds for advanced casting. Addit Manuf, 2021, 40. 101889

[3] SadarangJ, NayakRK. Utilization of fly ash as an alternative to silica sand for green sand mould casting process. J Manuf Process, 2021, 68: 1553-1561.

[4] FernaldRD. Casting a genetic light on the evolution of eyes. Science, 2006, 313: 1914-1918.

[5] GaoM, LiL, WangQ. Integration of additive manufacturing in casting: advances, challenges, and prospects. Int J Precis Eng Manuf-Green Tech, 2022, 9: 305-322.

[6] SinghS, RamakrishnaS, GuptaMK. Towards zero waste manufacturing: a multidisciplinary review. J Clean Prod, 2017, 168: 1230-1243.

[7] ShimizuK, XinbaY, TanakaM, et al.. Mechanical properties of spheroidal graphite cast iron made by reduced pressure frozen mold casting process. Mater Trans, 2009, 50: 1128-1134.

[8] ShiJ, ShanZ, YangH, et al.. Research on frozen sand mold casting technology for complex thin-walled aluminum alloy castings. Mater Today Commun, 2024, 41. 110907

[9] MooreC, BeetD. Effset-metallurgy, sand technology and economics. Foundry Trade J, 1979, 146: 1049-1063

[10] YasuhiroH, HidekazuM. Reduced-pressure frozen mold casting method and casting characterization. Foundry Technol, 2015, 36: 1225-1228

[11] OmuraN, TadaS. Effect of water content of frozen mold on fluidity of aluminum alloy. Light Metals, 2016, 2012: 989-992

[12] TadaS, NishioT, KobayashiK. Effect of colloidal silica addition on compressive strength of frozen mould. Int J Cast Metal Res, 2008, 21: 260-264.

[13] ShanZ, YangH, YanD, et al.. Research on green casting technology and equipment of digital frozen sand mold. Int J Metalcast, 2023, 17: 2439-2451.

[14] YangH, ShanZ, YanD, et al.. Research on forming method of additive manufacturing of frozen sand mold. Heliyon, 2023, 9. e19340

[15] ShiJ, ShanZ, YangH. Advancing sustainable casting through cryogenic gradient forming of frozen sand molds: design, error control, and experimental validation. J Mater Sci Technol, 2024, 203: 211-226.

[16] VelchevS, KolevI, IvanovK. Empirical models for specific energy consumption and optimization of cutting parameters for minimizing energy consumption during turning. J Clean Prod, 2014, 80: 139-149.

[17] SihagN, SangwanKS. A systematic literature review on machine tool energy consumption. J Clean Prod, 2020, 275. 123125

[18] XuL, HuangC, LiC. A novel intelligent reasoning system to estimate energy consumption and optimize cutting parameters toward sustainable machining. J Clean Prod, 2020, 261. 121160

[19] ChenXZ, LiCB, TangY. Energy efficient cutting parameter optimization. Front Mech Eng, 2021, 16: 221-248.

[20] ZhaoX, LiC, ChenX. Data-driven cutting parameters optimization method in multiple configurations machining process for energy consumption and production time saving. Int J Precis Eng Manuf-Green Tech, 2022, 9: 709-728.

[21] LuF, ZhouG, LiuY. Ensemble transfer learning for cutting energy consumption prediction of aviation parts towards green manufacturing. J Clean Prod, 2022, 331. 129920

[22] SóbesterA, LearySJ, KeaneAJ. On the design of optimization strategies based on global response surface approximation models. J Global Optim, 2005, 33: 31-59.

[23] Rama KotaiahK, SrinivasJ, BabuKJ. Prediction of optimal cutting states during inward turning: an experimental approach. Mater Manuf Process, 2010, 25: 432-441.

[24] SiL, WangZB, JiangG. Fusion recognition of shearer coal-rock cutting state based on improved RBF neural network and DS evidence theory. IEEE Access, 2019, 7: 122106-122121.

[25] LafifiB, HamrouniA, KhoualdiaT. Prediction and optimization of the bearing capacity of strip footing resting on soft soil improved with stone columns using RSM, ANN, and multi-objective GA. Innov Infrastruct Solut, 2024, 9146.

[26] LabidiA, TebassiH, BelhadiS. Cutting conditions modeling and optimization in hard turning using RSM, ANN and desirability function. J Fail Anal Prev, 2018, 18: 1017-1033.

[27] AsilturkI, KahramanliH, MounayriHE. Prediction of cutting forces and surface roughness using artificial neural network (ANN) and support vector regression (SVR) in turning 4140 steel. Mater Sci Technol, 2012, 28: 980-986.

[28] ArifinA, WuYR. Integrated multi-objective optimization on the geometrical design of a disk-type milling cutter with multiple inserts applying uniform design, RBF neural network, and PSO algorithm. Int J Adv Manuf Technol, 2022, 121: 4829-4846.

[29] Safaei-FaroujiM, ThanhHV, DaiZ. Exploring the power of machine learning to predict carbon dioxide trapping efficiency in saline aquifers for carbon geological storage project. J Clean Prod, 2022, 372. 133778

[30] JurkovicZ, CukorG, BrezocnikM. A comparison of machine learning methods for cutting parameters prediction in high speed turning process. J Intell Manuf, 2018, 29: 1683-1693.

[31] YeganefarA, NiknamSA, AsadiR. The use of support vector machine, neural network, and regression analysis to predict and optimize surface roughness and cutting forces in milling. Int J Adv Manuf Technol, 2019, 105: 951-965.

[32] ZertiA, YalleseMA, MeddourI. Modeling and multi-objective optimization for minimizing surface roughness, cutting force, and power, and maximizing productivity for tempered stainless steel AISI 420 in turning operations. Int J Adv Manuf Technol, 2019, 102: 135-157.

[33] SunY, GuoC, LiQ. Optimization of rock cutting process parameters with disc cutter for wear and cutting energy reduction based on the discrete element method. J Clean Prod, 2023, 391. 136160

[34] MaY, HuangZ, LiQ. Cutter layout optimization for reduction of lateral force on PDC bit using Kriging and particle swarm optimization methods. J Petrol Sci Eng, 2018, 163: 359-370.

[35] LiC, XiaoQ, TangY. A method integrating Taguchi, RSM and MOPSO to CNC machining parameters optimization for energy saving. J Clean Prod, 2016, 135: 263-275.

[36] DengZ, ZhangH, FuY. Optimization of process parameters for minimum energy consumption based on cutting specific energy consumption. J Clean Prod, 2017, 166: 1407-1414.

[37] ChengY, YangJ, QinC. Tool design and cutting parameter optimization for side milling blisk. Int J Adv Manuf Technol, 2019, 100: 2495-2508.

[38] JamilM, KhanAM, HegabH. Milling of Ti-6Al-4V under hybrid Al₂O₃-MWCNT nanofluids considering energy consumption, surface quality, and tool wear: a sustainable machining. Int J Adv Manuf Technol, 2020, 107: 4141-4157.

[39] ShaoH, WangHL, ZhaoXM. A cutting power model for tool wear monitoring in milling. Int J Mach Tool Manu, 2004, 44: 1503-1509.

[40] ZhaoGY, LiuZY, HeY. Energy consumption in machining: classification, prediction, and reduction strategy. Energy, 2017, 133: 142-157.

[41] DorethK, HenjesJ, KröningS. Approach to forecast energy consumption of machine tools within the design phase. Adv Mater Res, 2013, 769: 278-284.

[42] BinderM, KlockeF, DoebbelerB. Abrasive wear behavior under metal cutting conditions. Wear, 2017, 376: 165-171.

[43] KhaliliM, EivaniAR, SeyedeinSH. The effect of multi-pass friction stir processing on microstructure and mechanical properties of dual-phase brass alloy. J Mater Res Technol, 2022, 21: 1177-1195.

[44] LiuY, LiskiewiczTW, BeakeBD. Dynamic changes of mechanical properties induced by friction in the Archard wear model. Wear, 2019, 428: 366-375.

[45] ArchardJF. Contact and rubbing of flat surfaces. J Appl Phys, 1953, 24: 981-988.

[46] KhruschovMM. Principles of abrasive wear. Wear, 1974, 28: 69-88.

[47] BriscoeB. Wear of polymers: an essay on fundamental aspects. Tribol Int, 1981, 14: 231-243.

[48] ShiJ, ShanZ, YangH. Experimental and modeling investigation of freezing behavior for frozen sand molds. Int J Heat Mass Tran, 2023, 215. 124499

[49] ShiJ, ShanZ, YangH. Research on the macro-and meso-mechanical properties of frozen sand mold based on Hertz-Mindlin with Bonding model. Particuology, 2024, 88: 176-191.

[50] OnoI, NakashimaH, ShimizuH. Investigation of elemental shape for 3D DEM modeling of interaction between soil and a narrow cutting tool. J Terramechanics, 2013, 50: 265-276.

[51] SardinasRQ, ReisP, DavimJP. Multi-objective optimization of cutting parameters for drilling laminate composite materials by using genetic algorithms. Compos Sci Technol, 2006, 66: 3083-3088.

[52] WangJ, SunZ, GuL, et al.. Investigating the effect of laser cutting parameters on the cut quality of Inconel 625 using response surface method (RSM). Infrared Phys Techn, 2021, 118. 103866

[53] ZhangX, YuT, ZhaoJ. An analytical approach on stochastic model for cutting force prediction in milling ceramic matrix composites. Int J Mech Sci, 2020, 168. 105314

[54] EffendiMK, SoepangkatBO, NorcahyoR. Cutting force and surface roughness optimizations in end milling of GFRP composites utilizing BPNN-firefly method. Inter J Integr Eng, 2021, 13: 297-306.

[55] JiangY, HuangW, TianY, et al.. Research on cutting tool edge geometry design based on SVR-PSO. Int J Adv Manuf Technol, 2024, 131: 5047-5059.

[56] TranVQ. Using artificial intelligence approach for investigating and predicting yield stress of cemented paste backfill. Sustainability, 2023, 152892.

[57] AdnanRM, MostafaRR, DaiHL, et al.. Pan evaporation estimation by relevance vector machine tuned with new metaheuristic algorithms using limited climatic data. Eng Appl Comp Fluid, 2023, 172192258.

Funding

National Key R&D Program of China(2021YFB3401200)

Jiangsu Provincial Basic Research Program (Natural Science Foundation) Youth Fund(BK20230885)

High-quality Development Project of Ministry of Industry and Information Technology

RIGHTS & PERMISSIONS

Shanghai University and Periodicals Agency of Shanghai University and Springer-Verlag GmbH Germany, part of Springer Nature