Modeling of flow and debris ejection in blasting erosion arc machining in end milling mode

Abstract

Blasting erosion arc machining (BEAM) is a typical arc discharge machining technology that was developed around 2012 to improve the machinability of difficult-to-cut materials. End milling BEAM has been successfully developed and preliminarily applied in industry. However, owing to the high complexity of the flow field and the difficulty of observing debris in the discharge gap, studies of the flow and debris in end milling BEAM are limited. In this study, fluid dynamics simulations and particle tracking are used to investigate the flow characteristics and debris ejection processes in end milling BEAM. Firstly, the end milling BEAM mode is introduced. Then the numerical modeling parameters, geometric models, and simulation methods are presented in detail. Next, the flow distribution and debris ejection are described, analyzed, and discussed. The velocity and pressure distributions of the axial feed and radial feed are observed; the rotation speed and milling depth are found to have almost no effect on the flow velocity magnitude. Further, debris is ejected more rapidly in the radial feed than in the axial feed. The particle kinetic energy tends to increase with increasing milling depth, and smaller particles are more easily expelled from the flushing gap. This study attempts to reveal the flow field properties and debris ejection mechanism of end milling BEAM, which will be helpful in gaining a better understanding of BEAM.

Keywords

Modeling / Flow / Debris ejection / Blasting erosion arc machining (BEAM) / End milling

References

[1] Jithin S, Raut A, Bhandarkar UV, et al. Fe modeling for single spark in EDM considering plasma flushing efficiency. Proc Manuf, 2018, 26: 617-628.

[2] Fridman A, Yang Y, Cho YI. Plasma discharge in liquid: water treatment and applications, 2012, London: CRC Press

[3] Wu X, Liu Y, Zhang X, et al. Sustainable and high-efficiency green electrical discharge machining milling method. J Clean Prod, 2020, 274: 123040.

[4] Meshcheriakov G, Nosulenko V, Meshcheriakov N, et al. Physical and technological control of arc dimensional machining. CIRP Ann, 1988, 37: 209-212.

[5] Yuan R, Wei B, Luo Y et al (2010) High-speed electroerosion milling of superalloys. In: ISEM-16, Shanghai, pp 207–210

[6] Trimmer AL, Hayashi S, Lamphere M (2010) Advancement in high speed electro-erosion processes for machining tough metals. In: Proceedings of the 16th international symposium on electromachining, Shanghai

[7] Wang F, Liu Y, Tang Z, et al. Ultra-high-speed combined machining of electrical discharge machining and arc machining. Proc Inst Mech Eng Part B J Eng Manuf, 2014, 228: 663-672.

[8] Wang F, Liu Y, Zhang Y, et al. Compound machining of titanium alloy by super high speed EDM milling and arc machining. J Mater Process Technol, 2014, 214: 531-538.

[9] Zhang M, Zhang QH, Kong DZ et al (2014) The analysis of processing factors for electro-arc machining. In: Applied mechanics and materials. Trans Tech Publ, vol 470, pp 585–588

[10] Kou Z, Han F, Wang G. Research on machining Ti6Al4V by high-speed electric arc milling with breaking arcs via mechanical-hydrodynamic coupling forces. J Mater Process Technol, 2019, 271: 499-509.

[11] Zhao W, Gu L, Xu H, et al. A novel high efficiency electrical erosion process—blasting erosion arc machining. Proc Cirp, 2013, 6: 621-625.

[12] Xu H, Gu L, Zhao W, et al. Influence of flushing holes on the machining performance of blasting erosion arc machining. Proc Inst Mech Eng Part B J Eng Manuf, 2017, 231: 1949-1960.

[13] Wang CL, Chen JP, Gu L, et al. Blasting erosion arc machining of turbine blisk flow channel with laminated electrode. Proc Cirp, 2016, 42: 317-321.

[14] Farhadi A, Zhu Y, Gu L, et al. Electric arc sweep milling of open channels. Int J Adv Manuf Technol, 2019, 102: 673-683.

[15] Han H, Hui X, Lin G, et al. Flow field simulation and machining experiment of flank milling blasting erosion arc machining. J Mech Eng, 2015, 51: 176-183 (in Chinese)

[16] Chen J, Gu L, Xu H, et al. Study on blasting erosion arc machining of Ti-6Al-4V alloy. Int J Adv Manuf Technol, 2016, 85: 2819-2829.

[17] Gu L, Chen J, Xu H, et al. Blasting erosion arc machining of 20 vol.% SiC/Al metal matrix composites. Int J Adv Manuf Technol, 2016, 87: 2775-2784.

[18] Chen J, Gu L, Zhu Y, et al. High efficiency blasting erosion arc machining of 50 vol.% SiC/Al matrix composites. Proc Inst Mech Eng Part B J Eng Manuf, 2018, 232: 2226-2235.

[19] Sheikholeslami M, Jafaryar M, Ali JA, et al. Simulation of turbulent flow of nanofluid due to existence of new effective turbulator involving entropy generation. J Mol Liq, 2019, 291: 111283.

[20] Launder B, Spalding D. The numerical computation of turbulent flows. Comput Method Appl M, 1974, 3(2): 269-289.

[21] Zhao Y, Liu Z, Li X, et al. A modified turbulence model for simulating airflow aircraft cabin environment with mixed convection. Build Simul, 2020, 13: 665-675.

[22] Marek M. Numerical simulation of a gas flow in a real geometry of random packed bed of Raschig rings. Chem Eng Sci, 2017, 161: 382-393.

[23] Chen J, Gu L, Liu X, et al. Combined machining of SiC/Al composites based on blasting erosion arc machining and CNC milling. Int J Adv Manuf Technol, 2018, 96: 111-121.

[24] Gu L, Chen J, Zhu Y, et al. Influence of reinforcement particles on the mechanism of the blasting erosion arc machining of SiC/Al composites. Int J Adv Manuf Technol, 2018, 99: 1119-1129.

Funding

Natural Science Foundation of China(51975371)

Innovation and entrepreneurship project for high-level talents in Jiangsu province(164040022)