Chatter stability prediction in high-speed micromilling of Ti6Al4V via finite element based microend mill dynamics

Abstract

High-speed micromilling (spindle speeds 100 000 r/min) can create complex three-dimensional microfeatures in difficult-to-machine materials. The micromachined surface must be of high quality, to meet functional requirements. However, chatter-induced dynamic instability deteriorates the surface quality and can be detrimental to tool life. Chatter-free machining can be accomplished by identifying stable process parameters via stability lobe diagram. To generate accurate stability lobe diagram, it is essential to determine the microend mill dynamics. Frequency response function is required to determine the tool-tip dynamics obtained by experimental impact analysis. Note that application of impact load at the microend mill tip (typically 100 – 500 μm) is not feasible as it would invariably end with tool failure. Consequently, alternative methods need to be developed to identify the microend mill dynamics. In the present work, the frequency response function for the microend mill is obtained by finite element method modal analysis. The frequency response function obtained from modal analysis has been verified from the experimentally obtained frequency response function. The experimental frequency response function was obtained by impacting the microend mill near the taper portion with an impact hammer and measuring the vibration of the tool-tip with a laser displacement sensor. The fundamental frequency obtained from finite element method modal analysis shows a difference of 6.6% from the experimental fundamental frequency. Microend mill dynamics obtained from the finite element method is used for chatter prediction in high-speed micromilling operations. The stability lobe diagram predicts the stability boundary accurately at 60 000 r · min^–1 and 80 000 r/min; however, a slight deviation is observed at 100 000 r/min.

Keywords

Chatter / Micromilling / Microend mill dynamics / Frequency response function / Finite element modal analysis

References

[1] Jun MB, DeVor RE, Kapoor SG. Investigation of the dynamics of microend milling—part I: model development. J Manuf Sci Eng, 2006, 128(4): 893-900.

[2] Jin X, Altintas Y. Chatter stability model of micro-milling with process damping. J Manuf Sci Eng, 2013, 135(3): 031011.

[3] Miao JC, Chen GL, Lai XM, et al. Review of dynamic issue in micro-end milling. Int J Adv Manuf Technol, 2007, 31(9–10): 897-904.

[4] Ducobu F, Filippi E, Rivière-Lorphèvre E (2009) Chip formation and minimum chip thickness in micro-milling. In: Proceedings of the CIRP conference on modeling of machining operations, pp 339–346

[5] Quintana G, Ciurana J. Chatter in machining processes: a review. Int J Mach Tools Manuf, 2011, 51(5): 363-376.

[6] Graham E, Mehrpouya M, Nagamune R, et al. Robust prediction of chatter stability in micro milling comparing edge theorem and LMI. CIRP J Manuf Sci Technol, 2014, 7(1): 29-39.

[7] Rahnama R, Sajjadi M, Park SS. Chatter suppression in micro end milling with process damping. J Mater Process Technol, 2009, 209(17): 5766-5776.

[8] Malekian M, Park SS, Jun MB. Modeling of dynamic micro-milling cutting forces. Int J Mach Tools Manuf, 2009, 49(7): 586-598.

[9] Afazov SM, Zdebski D, Ratchev SM, et al. Effects of micro-milling conditions on the cutting forces and process stability. J Mater Process Technol, 2013, 213(5): 671-684.

[10] Afazov SM, Ratchev SM, Segal J, et al. Chatter modeling in micro-milling by considering process nonlinearities. Int J Mach Tools Manuf, 2012, 56: 28-38.

[11] Mascardelli BA, Park SS, Freiheit T. Substructure coupling of microend mills to aid in the suppression of chatter. J Manuf Sci Eng, 2008, 130(1): 119-129.

[12] Mancisidor I, Urkiola A, Barcena R, et al. Receptance coupling for tool point dynamic prediction by fixed boundaries approach. Int J Mach Tools Manuf, 2014, 78: 18-29.

[13] Singh KK, Kartik V, Singh R. Modeling dynamic stability in high-speed micromilling of Ti-6Al-4V via velocity and chip load dependent cutting coefficients. Int J Mach Tools Manuf, 2015, 96: 56-66.

[14] Song QH, Liu ZQ, Shi ZY. Chatter stability for micromilling processes with flat end mill. Int J Adv Manuf Technol, 2014, 71(5–8): 1159-1174.

[15] Schmitz TL, Donalson RR. Predicting high-speed machining dynamics by substructure analysis. CIRP Ann Manuf Technol, 2000, 49(1): 303-308.

[16] Altintas Y, Budak E. Analytical prediction of stability lobes in milling. Ann CIRP, 1995, 44(1): 357-362.

[17] Altintas Y. Manufacturing automation: principles of metal cutting and machine tool vibrations, 2000, Cambridge: Cambridge University Press

[18] Documentation, Abaqus, and User Manual (2010) Version 6.10. Dassault systemes

[19] Simulia D Abaqus 6.11 theory manual, 2011, Providence: DS SIMULIA Corp.

[20] Schmitz TL, Smith KS. Machining dynamics frequency response to improved productivity, 2008, Berlin: Springer

[21] Singh KK, Singh R, Kartik V. Comparative study of chatter detection methods for high-speed micromilling of Ti6Al4V. Procedia Manuf, 2015, 1(1): 593-606.

[22] Singh KK, Kartik V, Singh R. Modeling of dynamic instability via segmented cutting coefficients and chatter onset detection in high-speed micromilling of Ti6Al4V. J Manuf Sci Eng, 2017, 139(5): 051005.