Friction identification and compensation design for precision positioning

Abstract

Precision positioning systems driven by linear motors are vulnerable to force disturbances owing to the reduction of gear transmission. The friction, included in the disturbance, can be modeled and compensated to improve the servo performance. This paper proposes a modified Stribeck friction model (SFM) and an optimization algorithm for consistency with the positioning platform. The compensators based on the friction model and disturbance observer (DOB) are simulated. The simulation results show that as compared with the DOB compensator (the velocity recovers by 5.19%), the friction model based compensator (the velocity recovers by 10.66%) exhibits a better performance after adding the disturbance. Moreover, compensation comparisons among the Coulomb friction, traditional SFM, and modified SFM are performed. The experimental results show that the following error with modified SFM compensation improves by 67.67% and 51.63% at a speed of 0.005 m/s and 0.05 m/s, compared with the Coulomb friction compensation. This demonstrates that the proposed model, optimization algorithm, and compensator can reduce the following error effectively.

Keywords

Precision positioning / Friction compensation / Identification / Modeling

References

[1] Chen MY, Lu JS. High-precision motion control for a linear permanent magnet iron core synchronous motor drive in position platform. IEEE Trans Ind Inform, 2014, 10(1): 99-108.

[2] Yao WH, Tung PC, Fuh CC, et al. A robust uncertainty controller with system delay compensation for an ILPMSM system with unknown system parameters. IEEE Trans Ind Electron, 2011, 58(10): 4727-4735.

[3] Wu Y, Jiang H, Zou M. The research on fuzzy PID control of the permanent magnet linear synchronous motor. Phys Procedia, 2012, 24: 1311-1318.

[4] Ruderman M, Iwasaki M. Observer of nonlinear friction dynamics for motion control. IEEE Trans Ind Electron, 2015, 62(9): 5941-5949.

[5] Yan M, Huang K, Shiu Y, et al. Disturbance observer and adaptive controller design for a linear-motor-driven table system. Int J Adv Manuf Technol, 2007, 35(3–4): 408-415.

[6] Zhang DL, Chen YP, Wu A, et al. Precision motion control of permanent magnet linear motors. Int J Adv Manuf Technol, 2007, 35(3–4): 301-308.

[7] Cho K, Kim J, Choi SB, et al. A high-precision motion control based on a periodic adaptive disturbance observer in a PMLSM. IEEE-ASME Trans Mechatron, 2015, 20(5): 2158-2171.

[8] Feng B, Zhang D, Yang J, et al. A novel time-varying friction compensation method for servomechanism. Math Probl Eng, 2015, 1: 1-16.

[9] Wu W. Disturbance compensation using feedforward and feedback for scanner direct current motor mechanism low speed regulation. J Dyn Syst Meas Control-Trans ASME, 2011, 137(4): 1614-1619.

[10] Wang XJ, Wang SP. High performance adaptive control of mechanical servo system with LuGre friction model: identification and compensation. J Dyn Syst Meas Control-Trans ASME, 2012, 134(1): 011021.

[11] Shen JC, Lu QZ, Wu CH, et al. Sliding-mode tracking control with DNLRX model-based friction compensation for the precision stage. IEEE-ASME Trans Mechatron, 2014, 19(2): 788-797.

[12] Kim J, Cho K, Jung H et al (2014) A novel method on disturbance analysis and feed-forward compensation in permanent magnet linear motor system. In: International conference on intelligent system, pp 394–399

[13] Villegas FJ, Hecker L, Peña ME, et al. Modeling of a linear motor feed drive including pre-rolling friction and aperiodic cogging and ripple. Int J Adv Manuf Technol, 2014, 73(1): 267-277.

[14] Tan WB, Li XW, Xiang HB, et al. Parameter identification of LuGre model based on analysis of steady state error. Opt Precis Eng, 2011, 3: 664-671.

[15] Li YX, Meng HR, Zhang B, et al. Stribeck friction measure system of servo table based on Labview. Chin J Liq Cryst Disp, 2015, 30(1): 180-185.

[16] Chen Q, Tao L, Nan Y, et al. Adaptive nonlinear sliding mode control of mechanical servo system with LuGre friction compensation. J Dyn Syst Meas Control, 2015, 138(2): 021003.

[17] Yeh S, Su H. Development of friction identification methods for feed drives of CNC machine tools. Int J Adv Manuf Technol, 2011, 52(1–4): 263-278.

[18] Harman JJ, Kaufman MR, Shrestha DK. Compensation and estimation of friction by using on-line input estimation algorithm. J Tribol, 2014, 136(2): 325

[19] Piatkowski T. Dahl and LuGre dynamic friction models—the analysis of selected properties. Mech Mach Theory, 2014, 73: 91-100.

[20] Lin CJ, Yau HT, Tian YC. Identification and compensation of nonlinear friction characteristics and precision control for a linear motor stage. IEEE-ASME Trans Mechatron, 2013, 18(4): 1385-1396.

[21] Kabziński J, Jastrzębski M (2014) Practical implementation of adaptive friction compensation based on partially identified LuGre model. In: the 19th international conference on methods and models in automation and robotics (MMAR), pp 699–704

[22] Wang XJ, Wang SP. Output torque tracking control of direct-drive rotary torque motor with dynamic friction compensation. J Frankl Inst, 2015, 352(11): 5361-5379.

Funding

Shanghai Municipal Natural Science Foundation(No.13ZR1415800)

National Natural Science Foundation of China (CN)(61573238)

Innovation Program of Shanghai Municipal Education Commission of China(14YZ008)

Jiangsu Key Laboratory for Advanced Robotics Technology Foundation(No.JAR201304)