Comparative study between wear of uncoated and TiAlN-coated carbide tools in milling of Ti6Al4V

Abstract

As is recognized widely, tool wear is a major problem in the machining of difficult-to-cut titanium alloys. Therefore, it is of significant interest and importance to understand and determine quantitatively and qualitatively tool wear evolution and the underlying wear mechanisms. The main aim of this paper is to investigate and analyse wear, wear mechanisms and surface and chip generation of uncoated and TiAlN-coated carbide tools in a dry milling of Ti6Al4V alloys. The quantitative flank wear and roughness were measured and recorded. Optical and scanning electron microscopy (SEM) observations of the tool cutting edge, machined surface and chips were conducted. The results show that the TiAlN-coated tool exhibits an approximately 44% longer tool life than the uncoated tool at a cutting distance of 16 m. A more regular progressive abrasion between the flank face of the tool and the workpiece is found to be the underlying wear mechanism. The TiAlN-coated tool generates a smooth machined surface with 31% lower roughness than the uncoated tool. As is expected, both tools generate serrated chips. However, the burnt chips with blue color are noticed for the uncoated tool as the cutting continues further. The results are shown to be consistent with observation of other researchers, and further imply that coated tools with appropriate combinations of cutting parameters would be able to increase the tool life in cutting of titanium alloys.

Keywords

Tool wear / Titanium alloy / Tungsten carbide tool / Wear mechanism / High speed machining

References

[1] Arrazola PJ, Garay A, Iriarte LM, et al. Machinability of titanium alloys (Ti6Al4V and Ti555.3). J Mater Process Technol, 2009, 209(5): 2223-2230.

[2] Niknam SA, Khettabi R, Songmene V. Davim JP. Machinability and machining of titanium alloys: a review. Machining of titanium alloys, 2014, Berlin: Springer 1-30.

[3] Nouari M, Makich H. On the physics of machining titanium alloys: interactions between cutting parameters, microstructure and tool wear. Metals, 2014, 4(3): 335-358.

[4] Arsecularatne JA, Zhang LC, Montross C. Wear and tool life of tungsten carbide, PCBN and PCD cutting tools. Int J Mach Tools Manuf, 2006, 46(5): 482-491.

[5] Zareena AR, Veldhuis SC. Tool wear mechanisms and tool life enhancement in ultra-precision machining of titanium. J Mater Process Technol, 2012, 212(3): 560-570.

[6] Santhanam T, Tierney P, Hunt JL. Properties and selection: nonferrous alloys and special-purpose materials, 1990, 10 Latrobe: Kennametal Inc

[7] Egashira K, Hosono S, Takemoto S, et al. Fabrication and cutting performance of cemented tungsten carbide micro-cutting tools. Precis Eng, 2011, 35(4): 547-553.

[8] Su HH, LIU P, FU Y, et al. Tool life and surface integrity in high-speed milling of titanium alloy TA15 with PCD/PCBN tools. Chin J Aeronaut, 2012, 25(5): 784-790.

[9] Li A, Zhao J, Wang D, et al. Failure mechanisms of a PCD tool in high-speed face milling of Ti-6Al-4V alloy. Int J Adv Manuf Technol, 2012, 67(9–12): 1959-1966.

[10] Jawaid A, Sharif S, Koksal S. Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy. J Mater Process Technol, 2000, 99(1–3): 266-274.

[11] Bhatt A, Attia H, Vargas R, et al. Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718. Tribol Int, 2010, 43(5–6): 1113-1121.

[12] Ghani J, Che HCH, Hamdan SH, et al. Failure mode analysis of carbide cutting tools used for machining titanium alloy. Ceram Int, 2013, 39(4): 4449-4456.

[13] Hartung PD, Kramer BM, von Turkovich BF. Tool wear in titanium machining. CIRP Ann Manuf Technol, 1982, 31(1): 75-80.

[14] Ezugwu EO, Wang ZM. Titanium alloys and their machinability—a review. J Mater Process Technol, 1997, 68(3): 262-274.

[15] Ginting A, Nouari M. Experimental and numerical studies on the performance of alloyed carbide tool in dry milling of aerospace material. Int J Mach Tools Manuf, 2006, 46(7–8): 758-768.

[16] Deng JX, Li YS, Song WL. Diffusion wear in dry cutting of Ti-6Al-4V with WC/Co carbide tools. Wear, 2008, 265(11–12): 1776-1783.

[17] Gerez JM, Sanchez-Carrilero M, Salguero J et al (2009) A SEM and EDS based study of the microstructural modifications of turning inserts in the dry machining of Ti6Al4V alloy. AIP Conf Proc 1181:567–574

[18] Pramanik A, Islam MN, Basak A, et al. Machining and tool wear mechanisms during machining titanium alloys. Adv Mater Res, 2013, 651: 338-343.

[19] Zhang S, Li JF, Sun J, et al. Tool wear and cutting forces variation in high-speed end-milling Ti-6Al-4V alloy. Int J Adv Manuf Technol, 2009, 46(1–4): 69-78.

[20] Astakhov VP, Davim JP (2008) Tools (geometry and material) and tool wear—Springer. In: machining: fundamentals and recent advances. Springer, Berlin, pp 25–57

[21] Dhar NR, Islam S, Kamruzzaman M, et al. Wear behavior of uncoated carbide inserts under dry, wet and cryogenic cooling conditions in turning C-60 steel. J Braz Soc Mech Sci Eng, 2006, 28(2): 146-152.

[22] Sharif S, Abd E, Sasahar H. Amin AKMN. Machinability of titanium alloys in drilling. Titanium alloys-towards achieving enhanced properties for diversified applications, 2012, Osaka: InTech

[23] König W, Fritsch R, Kammermeier D (1991) Physically vapor deposited coatings on tools: performance and wear phenomena. In: metallurgical coatings and thin films. Elsevier, Oxford, pp 316–324

[24] Zhang Y, Zhou Z, Wang J, et al. Diamond tool wear in precision turning of titanium alloy. Mater Manuf Process, 2013, 28(10): 1061-1064.

[25] Odelros S. Tool wear in titanium machinin, 2012, Uppasla: Uppasla University

[26] Bai Q (2014) Interactions between wear mechanisms in a WC-Co/Ti-6Al-4V machining tribosystem. Dissertation, Texas A&M University, USA

[27] Che-Haron CH, Jawaid A. The effect of machining on surface integrity of titanium alloy Ti-6% Al-4% V. J Mater Process Technol, 2005, 166(2): 188-192.

[28] Bermingham MJ, Palanisamy S, Dargusch MS. Understanding the tool wear mechanism during thermally assisted machining Ti-6Al-4V. Int J Mach Tools Manuf, 2012, 62: 76-87.

[29] Cotterell M, Byrne G. Dynamics of chip formation during orthogonal cutting of titanium alloy Ti-6Al-4V. CIRP Ann Manuf Technol, 2008, 57(1): 93-96.

[30] Li H, He G, Qin X, et al. Tool wear and hole quality investigation in dry helical milling of Ti-6Al-4V alloy. Int J Adv Manuf Technol, 2014, 71(5–8): 1511-1523.

[31] Sutter G, List G. Very high speed cutting of Ti-6Al-4V titanium alloy—change in morphology and mechanism of chip formation. Int J Mach Tools Manuf, 2013, 66: 37-43.

[32] Gao C, Zhang L. Effect of cutting conditions on the serrated chip formation in high-speed cutting. Mach Sci Technol, 2013, 17(1): 26-40.

[33] Wang Z, Nakashima S, Larson M. Energy efficient machining of titanium alloys by controlling cutting temperature and vibration. Procedia CIRP, 2014, 17: 523-528.