Hybrid fuzzy-grey-Taguchi based multi weld quality optimization of Al/Cu dissimilar friction stir welded joints

Abstract

Nowadays aluminum alloys substitute copper in various applications for weight reduction and cost savings. This paper presents fuzzy-grey Taguchi technique for optimization of friction stir welding condition with seven weld quality attributes of dissimilar Al/Cu joints with the minimum number of experiments for effective productivity and product quality. Taguchi’s L₁₆ orthogonal array was used to conduct the experiments. Fuzzy inference system was adapted to convert the multi quality characteristics into an equivalent single quality parameter which was optimized by Taguchi approach. Four parameters namely, rotational speed of the tool, welding speed, plunging depth and tool pin offset were varied in four levels for investigating the effects on the process output like tensile strength, compressive strength, percentage of elongation, bending angle, weld bead thickness and average hardness at the nugget zone. The hardness profile is consistent with the variation of the structure within the nugget zone (NZ). Confirmation experiment was conducted using predicted optimum parameter setting and it showed that the proposed approach could efficiently optimize weld quality parameters. The microstructural analyses were also performed for all the zones of the joints at both Al and Cu sides. It revealed the finer grain size at the NZ compared to the base material due to dynamic recrystallization.

Keywords

Dissimilar friction stir welding / Grey relational analysis / Fuzzy inference system / Multi-response optimization / Mechanical properties / Microstructural analysis

References

[1.] Al-Roubaiy AO, Nabat SM, Batako ADL. Experimental and theoretical analyses of friction stir welding of Al to Cu joints. Int J Adv Manuf Technol, 2014, 71: 1631-1642.

[2.] Genevois C, Girard M, Huneau B, et al. Interfacial reaction during friction stir welding of Al and Cu. Min Met Mater Soc, 2011, 42: 2290-2295.

[3.] Liu HJ, Shen JJ, Zhou L, et al. Microstructural characterisation and mechanical properties of friction stir welded joints of Al to Cu. Sci Technol Weld Join, 2011, 16(1): 92-99.

[4.] Thomas WM, Nicholas ED, Needham JC et al (1991) Friction stir welding. International Patent Application No. PCT/GB92/02203 and Great Britain Patent Application No. 9125978.8

[5.] Vidal C, Infante V, Vilaca P. Assessment of improvement techniques effect on fatigue behaviour of friction stir welded aerospace aluminium alloys. Proc Eng, 2010, 2: 1605-1616.

[6.] Sahu PK, Pal S. Multi-response optimization of process parameters in friction stir welded AM20 magnesium alloy by Taguchi grey relational analysis. J Magnes Alloys, 2015, 3: 36-46.

[7.] Padmanaban G, Balasubramanian V, Sarin Sundar JK. Influences of welding processes on microstructure, hardness, and tensile properties of AZ31B magnesium alloy. J Mater Eng Perform, 2010, 19: 155-165.

[8.] Fattah-alhosseini A, Taheri AH. Effect of friction stir welding on corrosion behavior of pure copper in 3.5 wt% NaCl solution. J Manuf Process, 2015, 20: 98-103.

[9.] Lina J, Changa H, Wu M. Comparison of mechanical properties of pure copper welded using friction stir welding and tungsten inert gas welding. J Manuf Process, 2014, 16: 296-304.

[10.] Baraka A, Panoutsos G, Cater S. A real-time quality monitoring framework for steel friction stir welding using computational intelligence. J Manuf Process, 2015, 20: 137-148.

[11.] Seighalani KR, Givi MKB, Nasiri AM, et al. Investigations on the effects of the tool material, geometry, and tilt angle on friction stir welding of pure titanium. J Mater Eng Perform, 2010, 19: 955-962.

[12.] Sanders DG, Ramulu M, Klock-McCook EJ, et al. Characterization of super plastically formed friction stir weld in titanium 6 Al-4V: preliminary results. J Mater Eng Perform, 2008, 17: 187-192.

[13.] Uzun H. Friction stir welding of SiC particulate reinforced AA2124 aluminium alloy matrix composite. Mater Des, 2007, 28: 1440-1446.

[14.] Leitao C, Emílio B, Chaparro BM, et al. Formability of similar and dissimilar friction stir welded AA 5182-H111and AA 6016-T4 tailored blanks. Mater Des, 2009, 30: 3235-3242.

[15.] Grujicic M, Arakere G, Yen CF, et al. Computational investigations of hardness evolution during friction stir welding of AA5083 and AA2139 aluminum alloys. J Mater Eng Perform, 2011, 20: 1097-1108.

[16.] Mofid MA, Abdollah-zadeh A, Ghaini FM. The effects of water cooling during dissimilar friction stir welding of Al alloy to Mg alloy. Mater Des, 2012, 36: 161-167.

[17.] Movahedi M, Kokabi AH, Seyed-Reihani SM, et al. Effect of annealing treatment on joint strength of aluminum/steel friction stir lap weld. Mater Des, 2013, 44: 487-492.

[18.] Sahu PK, Pal S, Pal SK, et al. Influence of plate position, tool offset and tool rotational speed on mechanical properties and microstructures of dissimilar Al/Cu friction stir welding joints. J Mater Process Technol, 2016, 235: 55-67.

[19.] Bisadi H, Tavakoli A, Tour SM, et al. The influences of rotational and welding speeds on microstructures and mechanical properties of friction stir welded Al5083 and commercially pure copper sheets lap joints. Mater Des, 2013, 43: 80-88.

[20.] Akinlabi ET. Effect of shoulder size on weld properties of dissimilar metal friction stir welds. J Mater Eng Perform, 2012, 21: 1514-1519.

[21.] Carlone P, Astarita A, Palazzo GS, et al. Microstructural aspects in Al–Cu dissimilar joining by FSW. Int J Adv Manuf Technol, 2015, 79: 1109-1116.

[22.] Vidal C, Infante V. Optimization of FS welding parameters for improving mechanical behavior of AA2024-T351 joints based on Taguchi method. J Mater Eng Perform, 2013, 22(8): 2261-2270.

[23.] Rao TB, Gopala Krishna A. Simultaneous optimization of multiple performance characteristics in WEDM for machining ZC63/SiCp MMC. Adv Manuf, 2013, 1: 265-275.

[24.] Shojaeefard MH, Khalkhali A, Akbari M, et al. Application of Taguchi optimization technique in determining aluminum to brass friction stir welding parameters. Mater Des, 2013, 52: 587-592.

[25.] Taguchi G. Introduction to quality engineering: designing quality into products and processes, 1986, New York: Kraus International Publications

[26.] Walia RS, Shan HS, Kumar P. Multi-response optimization of CFAAFM process through taguchi method and utility concept. Mater Manuf Proc, 2006, 21: 907-914.

[27.] Pal S, Malviya S, Pal SK, et al. Optimization of quality characteristics parameters in a pulsed metal inert gas welding process using grey-based Taguchi method. Int J Adv Manuf Technol, 2009, 44: 1250-1260.

[28.] Karande P, Gauri SK, Chakraborty S. Applications of utility concept and desirability function for materials selection. Mater Des, 2013, 45: 349-358.

[29.] Tiwary AP, Pradhan BB, Bhattacharyya B. Application of multi-criteria decision making methods for selection of micro-EDM process parameters. Adv Manuf, 2014, 2: 251-258.

[30.] Julong D. Introduction to grey system theory. J Grey Syst, 1989, 1: 1-24.

[31.] Datta S, Bandyopadhyay A, Pal PK. Grey-based Taguchi method for optimization of bead geometry in submerged arc bead-on-plate welding. Int J Adv Manuf Technol, 2008, 39: 1136-1143.

[32.] Kasman S. Multi-response optimization using the Taguchi-based grey relational analysis: a case study for dissimilar friction stir butt welding of AA6082-T6/AA5754-H111. Int J Adv Manuf Technol, 2013, 68: 795-804.

[33.] Zadeh LA. Fuzzy sets. Inf Control, 1965, 8: 338-353.

[34.] Mamdani EH, Assilian S. An experiment in linguistic synthesis with a fuzzy logic controller. Int J Man-Machine Stud, 1975, 7: 1-13.

Funding

Department of Mechanical Engineering, Indian Institute of Technology Guwahati