Machining of circular micro holes by electrochemical micro-machining process

Abstract

Machining of micro holes with micro electrochemical machining (micro ECM) process has been carried out with an indigenously developed set up. This paper describes relevant problems and solutions for the circular micro holes machining process on 304 stainless steel sheets with 60 μm thickness using high speed steel cylindrical tool of diameter 500 μm and using dilute H₂SO₄ as electrolyte. The taper angle variation of the machined hole is analyzed and reported for different experimental setting parameters. The minimum value of the taper angle of machined holes is achieved at the parameter setting of 0.4 mol/L H₂SO₄, 700 kHz, 600 ns and 21 V, for stainless steel sheets and HSS tool.

Keywords

Micro machining / Micro ECM / Micro-hole / Electrochemical dissolution / Short pulse voltage / Pulse power supply

References

[1] Bhattacharyya B, Munda J, Malapati M. Advancement in electrochemical micro-machining. Int J Mach Tools Manuf, 2004, 44(15): 1577-1589.

[2] Masuzawa T. State of the art of micromachining. Ann CIRP, 2000, 49(2): 473-488.

[3] Bhattacharyya B, Munda J. Experimental investigation into electrochemical micromachining (EMM) process. J Mater Process Technol, 2003, 140: 287-291.

[4] Bhattacharyya B, Malapati M, Munda J. Experimental study on electrochemical micromachining. J Mater Process Technol, 2005, 169(3): 485-492.

[5] Bhattacharyya B, Malapati M, Munda J, et al. Influence of tool vibration on machining performance in electrochemical micro-machining of copper. Int J Mach Tools Manuf, 2007, 47(2): 335-342.

[6] Zhang Z, Zhu D, Qu N, Wang M. Theoretical and experimental investigation on electrochemical micromachining. Microsyst Technol, 2007, 13: 607-612.

[7] Kim BH, Na CW, Lee YS, et al. Micro electrochemical machining of 3D micro structure using dilute sulpfuric acid. Ann CIRP, 2005, 54(1): 191-194.

[8] Kim BH, Park BJ, Chu CN. Fabrication of multiple electrodes by reverse EDM and their application in micro ECM. J Micromech Microeng, 2006, 16: 843.

[9] Ahn SH, Ryu SH, Choi DK, et al. Electro-chemical micro drilling using ultra short pulses. Precis Eng, 2004, 28: 129-134.

[10] Cagnon L, Kirchner V, Kock M, et al. Electrochemical micromachining of stainless steel by ultra short voltage pulses. Z Phys Chem, 2003, 217: 299-313.

[11] Munda J, Malapati M, Bhattacharyya B. Control of micro-spark and stray-current effect during EMM process. J Mater Process Technol, 2007, 194(1–3): 151-158.

[12] Sen M, Shan HS. A review of electrochemical macro- to micro-hole drilling processes. Int J Mach Tools Manuf, 2005, 45(2): 137-152.

[13] Li Y, Zheng Y, Yang G, Peng L. Localized electrochemical micromachining with gap control. Sens Actuators A, 2003, 108(1–3): 144-148.

[14] Jahan MP, Wong YS, Rahman M. A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. J Mater Process Technol, 2009, 209(4): 1706-1716.

[15] Lim HS, Wong YS, Rahman M, et al. A study on the machining of high-aspect ratio micro-structures using micro-EDM. J Mater Process Technol, 2003, 140(1–3): 318-325.

[16] Asad ABMA, Masaki T, Rahman M, et al. Tool-based micro-machining. J Mater Process Technol, 2007, 192–193: 204-211.

[17] Rahman AA, Mamat A, Wagiman A. Effect of machining parameters on hole quality of micro drilling for brass. Mod Appl Sci, 2009, 3(5): 221-230.

[18] Schuster R, Kirchner V, Allongue P, et al. Electrochemical micromachining. Science, 2000, 289(5476): 98-101.