V-belt transmissions of agricultural machines

Abstract

The article is devoted to the analysis of design features and operating conditions of V-belt transmissions of agricultural machinery. When designing these gears, it is recommended to give preference to gears made according to an open circuit or with a tension roller located outside the belt contour, to avoid cross and semi-cross gears, as well as multi-pulley gears with crossing shaft axles. To make the wider use of more progressive types of belts. It was shown that the features of V-belt transmissions of agricultural machinery require clarification of the methods for calculating transmissions with progressive types of V-belts and automatic belt tensioning methods. It was noted that special attention should be paid to transmissions with multi-profile belts, which calculation has not been sufficiently reflected in domestic regulatory documents. The advantages of such belts are especially noticeable under variable and shock loading. Based on the analysis, the recommendations for clarifying the calculation of belt drives with multi-profile belts were given. Analytical dependencies are proposed for determining the value of the nominal power transmitted by one belt (stream) of a multi-profile belt, allowing automation of the calculation of V-belt transmissions of agricultural machinery. For gears with a tension or guide roller that add an extra (sometimes reverse) bend of the belt, it is proposed to determine the coefficient taking into account different degrees of bending on the pulleys according to a graph built taking into account the linear hypothesis of summation of damages. It is recommended to calculate gears with spring-loaded tensioning rollers and design tensioning devices for such transmissions using a special method that takes into account the belt tensioning method. At the same time, the required value of the pre-tension of the belt can be significantly reduced, which will have a positive effect on its resource, without losing the traction capacity of the transmission itself. Expressions are given for finding the value of the pre-tension of belts, both for gears with tension due to the elasticity of the belt, and for gears with spring-loaded tension rollers. Conclusions and directions for further research are formulated.

Keywords

Belt drive / multi-profile V-belt / load / resource / traction capacity / belt tension

References

[1] Пронин Б.А., Баловнев Н.П., Жуков К.П. Ременные передачи. Машиностроение. Энциклопедия. Том IV-1. Детали машин. Конструкционная прочность. Трение, износ, смазка. М.: Машиностроение, 1995. С. 606-631.

[2] Баловнев Н.П. Анализ методов расчета клиноременных передач. В сб. Агрегатирование и приводы сельскохозяйственных машин. М.: НПО ВИСХОМ, 1985. С. 60-71.

[3] Флик Э.П., Баловнев Н.П., Вяткин А.А., Бассаман А.Е. Ускоренные испытания механических приводов зернокомбайнов на автономных стендах. Тракторы и сельхозмашины. 1987. № 9. С. 22-25.

[4] Флик Э.П. Механические приводы сельскохозяйственных машин. М.: Машиностроение, 1984, 266 с.

[5] ГОСТ 1284.3-96. Ремни приводные клиновые нормальных сечений. Передаваемые мощности.

[6] ТУ 38.105 1998-91. Ремни приводные клиновые зернокомбайнов «ДОН» и других сельскохозяйственных машин. Технические условия.

[7] Баловнев Н.П., Вавилов П.Г. О совершенствовании индивидуальной системы электроснабжения пассажирских вагонов. Тяжелое машиностроение. 2009. №. С. 35-39.

[8] Баловнев Н.П., Дмитриева Л.А. Расчет клиноременных передач сельхозмашин с автоматическим натяжением ремня. Тракторы и сельхозмашины. 2014. № 9. С. 39-41.

[9] Баловнев Н.П., Дмитриева Л.А., Семин И.Н. Экспериментальная оценка тяговой способности ременных передач с различными способами натяжения ремня. Известия московского государственного университета МАМИ. 2012. Т. 1. № 2(14). С. 23-29.

[10] Баловнев Н.П., Дмитриева Л.А., Семин И.Н. Результаты сравнительных испытаний клиноременных передач с различными способами натяжения ремней. Автомобильная промышленность. 2013. № 5. С. 19-21.

RIGHTS & PERMISSIONS

Balovnev N.P., Brovkina Y.I., Dmitrieva L.A.