Effect of quenching cooling rate on residual stress and microstructure evolution of 6061 aluminum alloy

Abstract

In this study, the cooling rate was manipulated by quenching with water of different temperatures (30, 60 and 100 °C). Surface and internal residual stresses in the quenched 6061 aluminum alloy samples were measured using hole-drilling and crack compliance methods, respectively. Then, the processability of the quenched samples was evaluated at cryogenic temperatures. The mechanical properties of the as-aged samples were assessed, and microstructure evolution was analyzed. The surface residual stresses of samples W30°C, W60°C and W100°C is −178.7, −161.7 and −117.2 MPa, respectively along x-direction, respectively; and −191.2, −172.1 and −126.2 MPa, respectively along y-direction. The sample quenched in boiling water displaying the lowest residual stress (∼34 % and ∼60% reduction in the surface and core). The generation and distribution of quenching residual stress could be attributed to the lattice distortion gradient. Desirable plasticity was also exhibited in the samples with relatively low quenching cooling rates at cryogenic temperatures. The strengthes of the as-aged samples are 291.2 to 270.1 MPa as the quenching water temperature increase from 30 °C to 100 °C. Fine and homogeneous β″ phases were observed in the as-aged sample quenched with boiling water due to the clusters and Guinier-Preston zones (GP zones) premature precipitated during quenching process.

Keywords

6061 aluminum alloy / residual stress / cooling rate / cryogenic cooling / mechanical properties / microstructure evolution

References

[1] YinZ-q, YiZhang. Direct polishing of aluminum mirrors with higher quality and accuracy. Applied Optics, 2015, 54(26): 7835-7841 J]

[2] WangZ-s, FanR-h, ChenK, et al. . Effect of temperature treatment on microstructure and electrochemical properties of 6061 aluminum alloy. International Journal of Electrochemical Science, 2021, 16(4): 210410 J]

[3] YanJ-b, KongG-b, ZhangL-xin. Low-temperature tensile behaviours of 6061-T6 aluminium alloy: Tests, analysis, and numerical simulation. Structures, 2023, 56: 105054 J]

[4] ZhangZ-w, YiY-p, YouW, et al. . Investigation of quench sensitivity and microstructure evolution during isothermal treatment in 2195 Al-Li alloy. Metals and Materials International, 2022, 2861423-1432 J]

[5] WangH-m, YiY-p, HuangS-quan. Investigation of quench sensitivity of high strength 2219 aluminum alloy by TTP and TTT diagrams. Journal of Alloys and Compounds, 2017, 690446-452 J]

[6] RobinsonJ S, HossainS, TrumanC E, et al. . Residual stress in 7449 aluminium alloy forgings. Materials Science and Engineering A, 2010, 527(10–11): 2603-2612 J]

[7] DolanG P, RobinsonJ S. Residual stress reduction in 7175-T73, 6061-T6 and 2017A-T4 aluminium alloys using quench factor analysis. Journal of Materials Processing Technology, 2004, 153–154: 346-351 J]

[8] KoçM, CulpJ, AltanT. Prediction of residual stresses in quenched aluminum blocks and their reduction through cold working processes. Journal of Materials Processing Technology, 2006, 174(1–3): 342-354 J]

[9] WawszczakR, BaczmańskiA, MarciszkoM, et al. . Evolution of microstructure and residual stress during annealing of austenitic and ferritic steels. Materials Characterization, 2016, 112: 238-251 J]

[10] MohamedS S, SamuelA M, DotyH W, et al. . Development of residual stresses in Al – Si engine blocks subjected to different metallurgical parameters. International Journal of Metalcasting, 2020, 14(1): 25-36 J]

[11] GaoH-j, WuS-f, WuQ, et al. . Experimental and simulation investigation on thermal-vibratory stress relief process for 7075 aluminium alloy. Materials & Design, 2020, 195: 108954 J]

[12] ShalvandiM, HojjatY, AbdullahA, et al. . Influence of ultrasonic stress relief on stainless steel 316 specimens: A comparison with thermal stress relief. Materials & Design, 2013, 46713-723 J]

[13] LiuJ, DuZ-y, SuJ-l, et al. . Effect of quenching residual stress on precipitation behaviour of 7085 aluminium alloy. Journal of Materials Science & Technology, 2023, 132: 154-165 J]

[14] ZhangY-x, YiY-p, HuangS-q, et al. . Influence of quenching cooling rate on residual stress and tensile properties of 2A14 aluminum alloy forgings. Materials Science and Engineering A, 2016, 674: 658-665 J]

[15] DongY-b, ShaoW-z, JiangJ-t, et al. . Minimization of residual stress in an Al-Cu alloy forged plate by different heat treatments. Journal of Materials Engineering and Performance, 2015, 24(6): 2256-2265 J]

[16] DongF, YiY-p, HuangS-q, et al. . Cryogenic formability and deformation behavior of 2060 Al – Li alloys with water-quenched and T4 aged temper. Materials Science and Engineering A, 2021, 823: 141722 J]

[17] JobbaM, MishraR K, NiewczasM. Flow stress and work-hardening behaviour of Al – Mg binary alloys. International Journal of Plasticity, 2015, 6543-60 J]

[18] WangC-g, YiY-p, WangH-h, et al. . Investigation on the formability and deformation mechanism of aluminum alloy thin-walled parts at cryogenic temperature. Journal of Materials Processing Technology, 2023, 319: 118041 J]

[19] DongF, HuangS-q, YiY-p, et al. . Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature. Journal of Alloys and Compounds, 2023, 968171992 J]

[20] DongF, YiY-p, HuangS-q, et al. . Refinement of second-phase particles and grain structures of 2219 Al Cu alloy forgings using an improved thermomechanical treatment process. Materials Characterization, 2021, 173110927 J]

[21] WangD, HuangS-q, YiY-p, et al. . Effects of cryogenic deformation on the microstructure and mechanical properties of high-strength aluminum alloys. Materials Characterization, 2022, 187111831 J]

[22] HuangJ-w, YiY-p, HuangS-q, et al. . Effects of cryogenic deformation on second-phase Al₂Cu particles and mechanical properties of 2219 Al-Cu alloy rings. Metals and Materials International, 2021, 27(5): 815-824 J]

[23] ZhaoL, Santos MacíasJ G, DolimontA, et al. . Comparison of residual stresses obtained by the crack compliance method for parts produced by different metal additive manufacturing techniques and after friction stir processing. Additive Manufacturing, 2020, 36101499 J]

[24] PrimeM B, HillM R. Residual stress, stress relief, and inhomogeneity in aluminum plate. Scripta Materialia, 2002, 46(1): 77-82 J]

[25] NerviS, SzabóB A. On the estimation of residual stresses by the crack compliance method. Computer Methods in Applied Mechanics and Engineering, 2007, 196(37–40): 3577-3584 J]

[26] ChengW, FinnieI. Measurement of residual stress distributions near the toe of an attachment welded on a plate using the crack compliance method. Engineering Fracture Mechanics, 1993, 46(1): 79-91 J]

[27] HuangK, YiY-p, HuangS-q, et al. . Cryogenic die-less spinning of aluminum alloy thin-walled curved components and microstructure evolution. Journal of Manufacturing Processes, 2023, 9232-41 J]

[28] ArchambaultP, GodardD. High temperature precipitation kinetics and ttt curve of a 7xxx alloy by in situ electrical resistivity measurements and differential calorimetry. Scripta Materialia, 2000, 42(7): 675-680 J]

[29] GaoM, WangM-j, WenL, et al. . TTP curves and microstructural evolution mechanism after quenching in aluminum alloy 6082. Metallography, Microstructure, and Analysis, 2012, 1(3): 165-169 J]

[30] DongF, YiY-p, HuangS-quan. Measuring internal residual stress in Al-Cu alloy forgings by crack compliance method with optimized parameters. Journal of Central South University, 2020, 27(11): 3163-3174 J]

[31] MagalhäesD C C, KliaugaA M, SordiV L. Flow behavior and fracture of Al-Mg-Si alloy at cryogenic temperatures. Transactions of Nonferrous Metals Society of China, 2021, 31(3): 595-608 J]

[32] ZhouP, SongY-l, HuaL, et al. . Mechanical behavior and deformation mechanism of 7075 aluminum alloy under solution induced dynamic strain aging. Materials Science and Engineering A, 2019, 759: 498-505 J]

[33] YangW-c, WangM-p, ZhangR-r, et al. . The diffraction patterns from β″ precipitates in 12 orientations in Al-Mg-Si alloy. Scripta Materialia, 2010, 62(9): 705-708 J]

[34] LingM, MehrezS, VigneshR V, et al. . Investigation on underwater friction stir processing of AZ-61 magnesium alloy. Materials Today Communications, 2023, 36: 106885 J]

[35] MarioaraC D, AndersenS J, JansenJ, et al. . Atomic model for GP-zones in a 6082 Al-Mg-Si system. Acta Materialia, 2001, 49(2): 321-328 J]

[36] RaoP N, ViswanadhB, JayaganthanR. Effect of cryorolling and warm rolling on precipitation evolution in Al6061 alloy. Materials Science and Engineering A, 2014, 6061-10 J]

[37] ZhenL, KangS B. DSC analyses of the precipitation behavior of two Al-Mg-Si alloys naturally aged for different times. Materials Letters, 1998, 37(6): 349-353 J]

[38] ChangC S T, BanhartJ. Low-temperature differential scanning calorimetry of an Al-Mg-Si alloy. Metallurgical and Materials Transactions A, 2011, 42(7): 1960-1964 J]