Characterization of heat treatment-driven microstructural evolution, mechanical properties and electrochemical behavior of direct powder forged Al–10Si–0.3Mg alloy

Abstract

This study investigated the effects of direct aging (DA), solution treatment (ST), and ST followed by DA (T6) on the microstructural, mechanical, and corrosion properties of direct powder forged Al–10Si–0.3Mg alloy specimens. Microstructural analyses conducted using optical microscopy, scanning electron microscopy, and electron backscatter diffraction revealed that among DA specimens, direct aging at 200°C (DA-2) exhibited significantly enhanced silicon (Si) particle distribution uniformity and minimal interparticle boundaries owing to increased diffusion bonding; ST specimens exhibited partial Si dissolution, higher porosity, and retained the interparticle boundaries; and T6 specimens exhibited improved microstructural uniformity and enhanced Si precipitation. Furthermore, mechanical property evaluations indicated that T6 treatment comprising ST at 500°C for 180 min followed by DA at 200°C for 360 min resulted in the highest tensile strength (207.15 MPa) and elongation (5.02%), followed closely by DA at 200°C for 360 min (203.13 MPa and 4.39%). These improvements were attributed to the lower residual stress, higher diffusion distances, and well-dispersed Si particles induced by DA-2 treatment. Corrosion analyses conducted using cyclic polarization and impedance spectroscopy indicated varied electrochemical responses, with DA-2 resulting in the lowest corrosion current and highest impedance, and ST resulting in the lowest corrosion resistance. Overall, DA at 200°C for 360 min was the most effective heat treatment, offering the optimal balance between mechanical and corrosion-resistance properties.

Keywords

Al–10Si–0.3Mg / direct powder forging / heat treatment / microstructure / mechanical properties / corrosion behavior

References

[1] Gupta AK, Lloyd DJ, Court SA. Precipitation hardening in Al–Mg–Si alloys with and without excess Si. Mater. Sci. Eng. A, 2001, 316(1–2): 11

[2] Z.Z. Kuai, Z.H. Li, B. Liu, W.P. Liu, and S. Yang, Effects of remelting on the surface morphology, microstructure, and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting, Mater. Chem. Phys, 285(2022), art. No. 125901.

[3] Fousová M, Dvorský D, Michalcová A, Vojtěch D. Changes in the microstructure and mechanical properties of additively manufactured AlSi10Mg alloy after exposure to elevated temperatures. Mater. Charact., 2018, 137: 119

[4] K. Liu, X.M. Chen, L.M. Tam, et al., Combined influence of traverse and rotation speeds in friction stir processing of AlSi10Mg alloy produced by laser-powder bed fusion, Mater. Chem. Phys., 323(2024), art. No. 129585.

[5] M. Coşkun, K.C. Dizdar, G. Tarakçi, G. Özer, and D. Dispinar, Recycling of additive manufactured AlSi10Mg and its effect on mechanical properties, Mater. Chem. Phys., 289(2022), art. No. 126411.

[6] Tang HP, Gao CF, Zhang Y, et al. . Effects of direct aging treatment on microstructure, mechanical properties and residual stress of selective laser melted AlSi10Mg alloy. J. Mater. Sci. Technol., 2023, 139: 198

[7] Dwivedi A, Singh M, Ramkumar J, Gangolu S. Influence of soaking time on microstructural, machinability, and mechanical properties of Al–10Si–0.3Mg alloy fabricated by direct powder forging. J. Mater. Eng. Perform., 2025, 34(5): 4039

[8] Ghedjati K, Fleury E, Hamani MS, Benchiheub M, Bouacha K, Bolle B. Elaboration of AlSi10Mg casting alloys using directional solidification processing. Int. J. Miner. Metall. Mater., 2015, 22(5): 509

[9] Xu CL, Wang HY, Qiu F, Yang YF, Jiang QC. Cooling rate and microstructure of rapidly solidified Al–20 wt.% Si alloy. Mater. Sci. Eng. A, 2006, 417(1–2): 275

[10] Ceschini L, Morri A, Toschi S, Johansson S, Seifeddine S. Microstructural and mechanical properties characterization of heat-treated and overaged cast A354 alloy with various SDAS at room and elevated temperature. Mater. Sci. Eng. A, 2015, 648: 340

[11] Zamani M, Seifeddine S, Jarfors AEW. High-temperature tensile deformation behavior and failure mechanisms of an Al–Si–Cu–Mg cast alloy—The microstructural scale effect. Mater. Des., 2015, 86: 361

[12] Hyer H, Zhou L, Park S, et al. . Understanding the laser powder bed fusion of AlSi10Mg alloy. Metallogr. Microstruct. Anal., 2020, 9(4): 484

[13] Aboulkhair NT, Everitt NM, Ashcroft I, Tuck C. Reducing porosity in AlSi10Mg parts processed by selective laser melting. Addit. Manuf., 2014, 1: 77

[14] Kuang J, Zhao XL, Zhang YQ, et al. . Impact of thermal exposure on the microstructure and mechanical properties of a twin-roll cast Al–Mn–Fe–Si strip. J. Mater. Sci. Technol., 2022, 107: 183

[15] Song R, Harada Y, Kumai S. Influence of cooling rate on primary particle and solute distribution in high-speed twin-roll cast Al–Mn based alloy strip. Mater. Trans., 2018, 59: 110

[16] Luo Q, Guo YL, Liu B, et al. . Thermodynamics and kinetics of phase transformation in rare earth-magnesium alloys: A critical review. J. Mater. Sci. Technol., 2020, 44: 171

[17] Krueger DDLoria EA. The development of Direct Age 718 for gas turbine engine disk applications. Superalloy 718—Metallurgy and Applications, 1989, 279

[18] Moustafa MA, Samuel FH, Doty HW. Effect of solution heat treatment and additives on the microstructure of Al–Si (A413.1) automotive alloys. J. Mater. Sci., 2003, 38(22): 4507

[19] Cao WD, Kennedy RLLoria EA. Application of direct aging to Allvac® 718Plus™ alloy for improved performance. Superalloys 718, 625, 706 and Derivatives, 2005, 213

[20] T.H. Park, M.S. Baek, H. Hyer, Y. Sohn, and K.A. Lee, Effect of direct aging on the microstructure and tensile properties of AlSi10Mg alloy manufactured by selective laser melting process, Mater. Charact., 176(2021), art. No. 111113.

[21] R. Casati, M.H. Nasab, M. Coduri, V. Tirelli, and M. Vedani, Effects of platform pre-heating and thermal-treatment strategies on properties of AlSi10Mg alloy processed by selective laser melting, Metals, 8(2018), No. 11, art. No. 954.

[22] Zakay A, Aghion E. Effect of post-heat treatment on the corrosion behavior of AlSi10Mg alloy produced by additive manufacturing. JOM, 2019, 71: 1150

[23] A. Gatto, C. Cappelletti, S. Defanti, and F. Fabbri, The corrosion behaviour of additively manufactured AlSi10Mg parts compared to traditional Al alloys, Metals, 13(2023), No. 5, art. No. 913.

[24] Gu XH, Zhang JX, Fan XL, Zhang LC. Corrosion behavior of selective laser melted AlSi10Mg alloy in NaCl solution and its dependence on heat treatment. Acta Metall. Sin. (Engl. Lett.), 2020, 33(3): 327

[25] Cabrini M, Lorenzi S, Pastore T, et al. . Effect of heat treatment on corrosion resistance of DMLS AlSi10Mg alloy. Electrochim. Acta, 2016, 206: 346

[26] E. Cerri and E. Ghio, Aging profiles of AlSi7Mg0.6 and AlSi10Mg0.3 alloys manufactured via laser-powder bed fusion: direct aging versus T6, Materials., 15(2022), No. 17, art. No. 6126.

[27] Li W, Li S, Liu J, et al. . Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism. Mater. Sci. Eng. A, 2016, 663: 116

[28] Tabatabaei N, Zarei-Hanzaki A, Moshiri A, Abedi HR. The effect of heat treatment on the room and high temperature mechanical properties of AlSi10Mg alloy fabricated by selective laser melting. J. Mater. Res. Technol., 2023, 23: 6039

[29] Zhou L, Mehta A, Schulz E, McWilliams B, Cho K, Sohn Y. Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment. Mater. Charact., 2018, 143: 5

[30] Girelli L, Tocci M, Gelfi M, Pola A. Study of heat treatment parameters for additively manufactured AlSi10Mg in comparison with corresponding cast alloy. Mater. Sci. Eng. A, 2019, 739: 317

[31] Saraswat E, Maharana HS, Narayana Murty SVS, et al. . Fabrication of Al–Si controlled expansion alloys by unique combination of pressureless sintering and hot forging. Adv. Powder Technol., 2020, 31(7): 2820

[32] Upadhyaya A, Upadhyaya GS. Powder Metallurgy: Science, Technology and Materials, 2011, Hyderabad. Universities Press

[33] S. Marola, S. Bosia, A. Veltro, et al., Residual Stresses in additively manufactured AlSi10Mg: Raman spectroscopy and X-ray diffraction analysis, Mater. Des., 202(2021), art No. 109550.

[34] Rafieazad M, Mohammadi M, Nasiri AM. On microstructure and early stage corrosion performance of heat-treated direct metal laser sintered AlSi10Mg. Addit. Manuf., 2019, 28: 107

[35] Zheng Y, Zhao ZH, Xiong RZ, et al. . Effect of post heat treatment on microstructure, mechanical property, and corrosion behavior of AlSi10Mg alloy fabricated by selective laser melting. Prog. Nat. Sci.: Mater. Int., 2024, 34(1): 89

[36] H. Herrera Hernández, A. Mandujano Ruiz, C.O. González Morán, et al., Microstructural and electrochemical study: Pitting corrosion mechanism on A390 Al–Si alloy and Ce–Mo treatment as a better corrosion protection, Materials, 17(2024), No. 12, art No. 3044.

[37] Mandal S, Bhushan B, Gupta RK, Mondal K. Influence of feedstock on the excellent corrosion inhibition effect of cattle manure. J. Mater. Eng. Perform., 2025, 34(1): 749

[38] Bordihn S, Mertens V, Engelhart P, et al. . Surface passivation by Al₂O₃ and a-SiN_x: H films deposited on wet-chemically conditioned Si surfaces. ECS J. Solid State Sci. Technol., 2012, 1(6): 320

[39] Bartzsch H, Glöß D, Böcher B, Frach P, Goedicke K. Properties of SiO₂ and Al₂O₃ films for electrical insulation applications deposited by reactive pulse magnetron sputtering. Surf. Coat. Technol., 2003, 174–175: 774

[40] B. Bhushan, A. Banerjee, S.N. Patel, et al., Electrochemical response and passivation affinity of Fe-based amorphous HVOF coatings prepared from pig iron on mild steel, Surf. Coat. Technol., 452(2023), art. No. 129082.

[41] B. Bhushan, A. Banerjee, P.K. Bijalwan, et al., Prolong passivation of a novel Fe-based amorphous coating derived from high P pig iron, J. Non-Cryst. Solids, 601(2023), art. No. 122051.

RIGHTS & PERMISSIONS

University of Science and Technology Beijing