Vertical plane depth-resolved surface potential and carrier separation characteristics in flexible CZTSSe solar cells with over 12% efficiency

Abstract

Cu₂ZnSn(S,Se)₄ (CZTSSe) solar cells have resource distribution and economic advantages. The main cause of their low efficiency is carrier loss resulting from recombination of photo-generated electron and hole. To overcome this, it is important to understand their electron-hole behavior characteristics. To determine the carrier separation characteristics, we measured the surface potential and the local current in terms of the absorber depth. The elemental variation in the intragrains (IGs) and at the grain boundaries (GBs) caused a band edge shift and bandgap (E_g) change. At the absorber surface and subsurface, an upward E_c and E_v band bending structure was observed at the GBs, and the carrier separation was improved. At the absorber center, both upward E_c and E_v and downward E_c-upward E_v band bending structures were observed at the GBs, and the carrier separation was degraded. To improve the carrier separation and suppress carrier recombination, an upward E_c and E_v band bending structure at the GBs is desirable.

Keywords

carrier separation / CZTSSe / flexible solar cell / local current / surface potential

References

[1] International Energy Agency. Special report on solar PV global supply chains. 2022. Accessed March 6, 2023.

[2] Wadia C, Alivisatos AP, Kammen DM. Materials availability expands the opportunity for large-scale photovoltaics deployment. Environ Sci Technol. 2009; 43 (6): 2072- 2077.

[3] U.S. Geological Survey. Rare earth elements-critical resources for high technology. 2002. Accessed March 6, 2023.

[4] Green MA, Dunlop ED, Siefer G, et al. Solar cell efficiency tables (Version 61). Prog Photovoltaics Res Appl. 2022; 31 (1): 3- 16.

[5] National Renewable Energy Laboratory. Best research-cell efficiencies. 2023. Accessed March 6, 2023.

[6] Son DH, Kim SH, Kim SY, et al. Effect of solid-H₂S gas reactions on CZTSSe thin film growth and photovoltaic properties of a 12.62% efficiency device. J Mater Chem A. 2019; 7 (44): 25279- 25289.

[7] Yang KJ, Kim S, Kim SY, et al. Sodium effects on the diffusion, phase, and defect characteristics of kesterite solar cells and flexible Cu₂ZnSn(S,Se)₄ with greater than 11% efficiency. Adv Funct Mater. 2021; 31 (29): 2102238.

[8] Yang KJ, Kim S, Kim SY, et al. Flexible Cu₂ZnSn(S,Se)₄ solar cells with over 10% efficiency and methods of enlarging the cell area. Nat Commun. 2019; 10: 2959.

[9] Yang KJ, Kim S, Sim JH, et al. The alterations of carrier separation in kesterite solar cells. Nano Energy. 2018; 52: 38- 53.

[10] Chen S, Walsh A, Gong XG, Wei SH. Classification of lattice defects in the kesterite Cu₂ZnSnS₄ and Cu₂ZnSnSe₄ earth-abundant solar cell absorbers. Adv Mater. 2013; 25 (11): 1522- 1539.

[11] Song J, Li SS, Huang CH, Crisalle OD, Anderson TJ. Device modeling and simulation of the performance of Cu(In_1-x,Ga_x) Se₂ solar cells. Solid-State Electron. 2004; 48 (1): 73- 79.

[12] Yang KJ, Son DH, Sung SJ, et al. A band-gap-graded CZTSSe solar cell with 12.3% efficiency. J Mater Chem A. 2016; 4 (26): 10151- 10158.

[13] Woo K, Kim Y, Yang W, et al. Band-gap-graded Cu₂ZnSn (S_1-x,Se_x)₄ solar cells fabricated by an ethanol-based, particulate precursor ink route. Sci Rep. 2013; 3: 3069.

[14] Guo H, Meng R, Wang G, et al. Band-gap-graded Cu₂ZnSn (S,Se)₄ drives highly efficient solar cells. Energy Environ Sci. 2022; 15 (2): 693- 704.

[15] Park HK, Cho Y, Kim K, et al. Tailored band structure of Cu (In,Ga) Se₂ thin-film heterojunction solar cells: depth profiling of defects and the work function. ACS Appl Mater Interfaces. 2022; 14 (30): 34697- 34705.

[16] Walsh A, Chen S, Wei SH, Gong XG. Kesterite thin-film solar cells: advances in materials modelling of Cu₂ZnSnS₄. Adv Energy Mater. 2012; 2 (4): 400- 409.

[17] Chen S, Walsh A, Yang JH, et al. Compositional dependence of structural and electronic properties of Cu₂ZnSn(S,Se)₄ alloys for thin film solar cells. Phys Rev B. 2011; 83 (12): 125201.

[18] Gershon T, Lee YS, Antunez P, et al. Photovoltaic materials and devices based on the alloyed kesterite absorber (Ag_xCu_1-x)₂ZnSnSe₄. Adv Energy Mater. 2016; 6 (10): 1502468.

[19] Yang Y, Kang X, Huang L, Pan D. Tuning the band gap of Cu₂ZnSn(S,Se)₄ thin films via lithium alloying. ACS Appl Mater Interfaces. 2016; 8 (8): 5308- 5313.

[20] Lin TY, Chen CH, Huang WC, Ho WH, Wu YH, Lai CH. Direct probing Se spatial distribution in Cu(In_xGa_1-x) Se₂ solar cells: a key factor to achieve high efficiency performance. Nano Energy. 2016; 19: 269- 278.

[21] Kim GY, Jo W, Jo HJ, Kim DH, Kang JK. Macroscopic and microscopic electrical properties of Cu(In,Ga) Se₂ thin-film solar cells with various Ga/(In+Ga) contents. Curr Appl Phys. 2015; 15 (2): S44- S50.

[22] Jeong AR, Kim GY, Jo W, et al. Local current transport and surface potential of photovoltaic Cu(In, Ga) Se₂ thin films probed by multi-scale imaging methods. Adv Nat Sci Nanosci Nanotechnol. 2013; 4 (4): 015007.

[23] Kim GY, Kim JR, Jo W, Son DH, Kim DH, Kang JK. Nanoscale observation of surface potential and carrier transport in Cu₂ZnSn(S,Se)₄ thin films grown by sputtering-based two-step process. Nanoscale Res Lett. 2014; 9: 10.

[24] Kim GY, Jeong AR, Kim JR, et al. Surface potential on grain boundaries and intragrains of highly efficient Cu₂ZnSn(S,Se)₄ thin-films grown by two-step sputtering process. Sol Energy Mater Sol Cells. 2014; 127: 129- 135.

[25] Li JB, Chawla V, Clemens BM. Investigating the role of grain boundaries in CZTS and CZTSSe thin film solar cells with scanning probe microscopy. Adv Mater. 2012; 24 (6): 720- 723.

[26] Kaur K, Nisika , Chowdhury AH, Qiao Q, Kumar M. Nanoscale charge transport and local surface potential distribution to probe the defect passivation in Cr-substituted earth abundant CZTS absorber layer. J Alloys Compd. 2021; 854: 157160.

[27] Xin H, Vorpahl SM, Collord AD, et al. Lithium-doping inverts the nanoscale electric field at the grain boundaries in Cu₂ZnSn (S,Se)₄ and increases photovoltaic efficiency. Phys Chem Chem Phys. 2015; 17 (37): 23859- 23866.

[28] Kim J, Kim GY, Son DH, et al. High photo-conversion efficiency Cu₂ZnSn(S,Se)₄ thin-film solar cells prepared by compound-precursors and metal-precursors. Sol Energy Mater Sol Cells. 2018; 183: 129- 136.

[29] Jeong WL, Kim KP, Kim J, et al. Impact of Na doping on the carrier transport path in polycrystalline flexible Cu₂ZnSn (S,Se)₄ solar cells. Adv Sci. 2020; 7 (21): 1903085.

[30] Karade V, Choi E, Gang MG, et al. Achieving low V_OC-deficit characteristics in Cu₂ZnSn(S,Se)₄ solar cells through improved carrier separation. ACS Appl Mater Interfaces. 2021; 13 (1): 429- 437.

[31] Park HK, Cho Y, Kim J, et al. Flexible kesterite thin-film solar cells under stress. npj Flex Electron. 2022; 6: 91.

[32] Melitz W, Shen J, Kummel AC, Lee S. Kelvin probe force microscopy and its application. Surf Sci Rep. 2011; 66 (1): 1- 27.

[33] Lanzoni EM, Gallet T, Spindler C, et al. The impact of Kelvin probe force microscopy operation modes and environment on grain boundary band bending in perovskite and Cu(In,Ga) Se₂ solar cells. Nano Energy. 2021; 88: 106270.

[34] Kim J, Park HK, Cho Y, et al. Photo-excited carrier transport and secondary phases of Na-engineered kesterite flexible thin films. Sol Energy Mater Sol Cells. 2023; 250: 112091.

[35] Kim K, Jeong I, Cho Y, et al. Mechanisms of extrinsic alkali incorporation in CIGS solar cells on flexible polyimide elucidated by nanoscale and quantitative analyses. Nano Energy. 2020; 67: 104201.

[36] Lee H, Jang Y, Nam SW, et al. Passivation of deep-level defects by cesium fluoride post-deposition treatment for improved device performance of Cu(In,Ga) Se₂ solar cells. ACS Appl Mater Interfaces. 2019; 11 (39): 35653- 35660.

[37] Kim K, Kim J, Gang MG, et al. A simple and robust route toward flexible CIGS photovoltaic devices on polymer substrates: atomic level microstructural analysis and local optoelectronic investigation. Sol Energy Mater Sol Cells. 2019; 195: 280- 290.

[38] Cojocaru-Mirédin O, Choi PP, Abou-Ras D, Schmidt SS, Caballero R, Raabe D. Characterization of grain boundaries in Cu(In,Ga) Se₂ films using atom-probe tomography. IEEE J Photovolt. 2011; 1 (2): 207- 212.

[39] Choi PP, Cojocaru-Mirédin O, Wuerz R, Raabe D. Comparative atom probe study of Cu(In,Ga) Se₂ thin-film solar cells deposited on soda-lime glass and mild steel substrates. J Appl Phys. 2011; 110 (12): 124513.

[40] Kim K, Jung C, Yim K, et al. Atom-scale chemistry in chalcopyrite-based photovoltaic materials visualized by atom probe tomography. ACS Appl Mater Interfaces. 2022; 14 (47): 52825- 52837.

[41] Siebentritt S, Avancini E, Bär M, et al. Heavy alkali treatment of Cu(In,Ga) Se₂ solar cells: surface versus bulk effects. Adv Energy Mater. 2020; 10 (8): 1903752.

[42] Schwarz T, Redinger A, Siebentritt S, et al. Variable chemical decoration of extended defects in Cu-poor Cu₂ZnSnSe₄ thin films. Phys Rev Mater. 2019; 3 (3): 035402.

[43] Schwarz T, Cojocaru-Mirédin O, Choi P, et al. Atom probe tomography study of internal interfaces in Cu₂ZnSnSe₄ thin-films. J Appl Phys. 2015; 118 (9): 095302.

[44] He M, Zhang X, Huang J, et al. High efficiency Cu₂ZnSn (S,Se)₄ solar cells with shallow Li_Zn acceptor defects enabled by solution-based Li post-deposition treatment. Adv Energy Mater. 2021; 11 (13): 2003783.

[45] Chen S, Yang JH, Gong XG, Walsh A, Wei SH. Intrinsic point defects and complexes in the quaternary kesterite semiconductor Cu₂ZnSnS₄. Phys Rev B. 2010; 81 (24): 245204.

[46] Ma Y, Li W, Feng Y, et al. Band bending near grain boundaries of Cu₂ZnSn(S,Se)₄ thin films and its effect on photovoltaic performance. Nano Energy. 2018; 51: 37- 44.

[47] Castañeda-Uribe OA, Reifenberger R, Raman A, Avila A. Depth-sensitive subsurface imaging of polymer nanocomposites using second harmonic Kelvin probe force microscopy. ACS Nano. 2015; 9 (3): 2938- 2947.

[48] Heath JT, Cohen JD, Shafarman WN. Bulk and metastable defects in CuIn_1-xGa_xSe₂ thin films using drive-level capacitance profiling. J Appl Phys. 2004; 95 (3): 1000- 1010.

[49] Wang W, Winkler MT, Gunawan O, et al. Device characteristics of CZTSSe thin-film solar cells with 12.6% efficiency. Adv Energy Mater. 2014; 4 (7): 1301465.

[50] Hanna G, Jasenek A, Rau U, Schock HW. Open circuit voltage limitations in CuIn_1-xGa_xSe₂ thin-film solar cells—dependence on alloy composition. Phys Stat Sol A. 2000; 179 (1): R7- R8.

[51] Kim SY, Kim SH, Hong S, et al. Secondary phase formation mechanism in the Mo-back contact region during sulfo-selenization using a metal precursor: effect of wettability between a liquid metal and substrate on secondary phase formation. ACS Appl Mater Interfaces. 2019; 11 (26): 23160- 23167.

[52] Kim SY, Son DH, Kim YI, et al. Void and secondary phase formation mechanisms of CZTSSe using Sn/Cu/Zn/Mo stacked elemental precursors. Nano Energy. 2019; 59: 399- 411.

[53] Park HK, Cho Y, Kim J, et al. Chemical tailoring of sodium content for optimization of interfacial band bending and alignment in flexible kesterite solar cells. Sol Energy Mater Sol Cells. 2021; 230: 111243.

[54] Kim SY, Son DH, Kim SH, et al. Effect of Cu-Sn-Se liquid phase on grain growth and efficiency of CZTSSe solar cells. Adv Energy Mater. 2020; 10 (14): 1903173.

[55] Werner F, Babbe F, Elanzeery H, Siebentritt S. Can we see defects in capacitance measurements of thin-film solar cells? Prog Photovolt Res Appl. 2019; 27 (11): 1045- 1058.

[56] Hegedus SS, Shafarman WN. Thin-film solar cells: device measurements and analysis. Prog Photovolt Res Appl. 2004; 12 (2-3): 155- 176.

[57] Han M, Zhang X, Zeng Z. An investigation of Na-related defects in Cu₂ZnSnSe₄. Phys Chem Chem Phys. 2017; 19 (27): 17799- 17804.

[58] Xiao W, Wang JN, Zhao XS, et al. Intrinsic defects and Na doping in Cu₂ZnSnS₄: a density-functional theory study. Sol Energy. 2015; 116: 125- 132.

RIGHTS & PERMISSIONS

2024 The Authors. Carbon Energy published by Wenzhou University and John Wiley & Sons Australia, Ltd.