Edible films (EF) are continuously developed as food packaging alternatives due to their biodegradable properties. EF can be made from polysaccharides, proteins, lipids, and composite components. The use of raw materials certainly affects the properties of EF. Some studies reported that mammalian gelatin films were significantly different from fish gelatin films. However, there have been different results among individual studies. Therefore, the present study would like to obtain a valid conclusion across different studies using a meta-analysis approach. Study selection was performed with the PRISMA guideline. There were six relevant studies and 28 data used for meta-analysis. The statistical analysis was calculated by using Hedges’d. The results show that fish gelatin films had significantly lower (p < 0.05) tensile strength, elastic modulus, water vapor permeability, and transparency compared to mammalian gelatin films. Besides, there were two additional factors that are also discussed such as different film fabrication methods and gelatin concentration. Those seasonal factors were conducted by using subgroup analysis and meta-regression, respectively. The results described that the film production method, i.e., casting and compression molding significantly effect (p < 0.05) the tensile strength and elongation at break. Slightly different from the method, gelatin concentration was significantly affected (p < 0.05) the tensile strength, elongation at break, and water vapor permeability.
The objective of this study was to determine the characteristics of fresh rice straw silage quality prepared with addition of Lactiplantibacillus plantarum 1A-2 and crude cellulase alone or in combination. Quality of the silage was observed through the chemical composition, chemical structure and in vitro digestibility. Six treatments were used in this study, i.e., 1) rice straw without any treatment as control, 2) rice straw with addition of 0.1% L. plantarum 1A-2 (LAB1), 3) rice straw with addition of 1% crude cellulase (E1), 4) rice straw with addition of 0.1% L. plantarum 1A-2 and 1% cellulase enzyme. (LAB1 E1), 5) rice straw with addition of 2% crude cellulase (E2), 6) rice straw with addition of 0.2% L. plantarum 1A-2 and 2% crude cellulase (LAB2E2). Each treatment was replicated by four times (n = 24). Ensilage was carried out for 60 days. Data obtained were analyzed by using one-way analysis of variance (ANOVA) according to complete randomized design. The result indicated that the treatments increased dry matter (DM) (p = 0.001), crude protein (p < 0.001) and lactic acid (p < 0.001). Meanwhile, reduced pH (p < 0.001) and organic acids (acetic, propionic and butyric (p < 0.001)). Total crystallinity index (TCI) of rice straw silage varied among treatments and decreased in crystallinity (%) except for LAB2E2, which showed the lowest crystalline size. The treatment increased DM digestibility (p = 0.397) with the highest in LAB2E2. There is significant effect (p < 0.001) on increasing the main SCFA products from in vitro rumen fermentation. This study suggests that addition of L. plantarum 1A-2 inoculant alone or with crude cellulase improved fresh rice straw silage quality.
Improper use of antibiotics to treat or prevent infections, and as a stimulant for livestock growth, can affect public health and the dairy industry due to the spread of antibiotic residues in milk. This systematic review and meta-analysis aimed to investigate antibiotic residues in raw and pasteurized milk in Iran. Data were collected through searching the databases, including Scopus, PubMed, Science Direct, Web of Science, Google Scholar, SID, and Magiran using the following keywords: “pasteurized milk”, “raw milk”, “milk”, “antibiotic residues”,” antibiotic”, and “Iran”. Finally, 40 eligible studies were selected for the systematic review and meta-analysis. According to the reviewed studies, the prevalence of antibiotic residues in raw and pasteurized milk was 26% (95% CI: 20–33%) and 21% (95% CI: 15–27%), respectively. It seems that the control measures are inefficient in dairy industry and milk collection centers for the presence of antibiotic residues and the time of antibiotic withdrawal during milk delivery. Permanent control of milk in the collection centers by the responsible organizations along with implementation of Hazard Analysis Critical Control Point system in milk factories can be very effective in reducing antibiotic residues.
The development of tolerant rice varieties using doubled-haploid technology is necessary to speed up the release of a variety tolerant to salinity stress. However, this requires a reliable screening method and selection index model for enhancing selection effectiveness. One approach is through the development of a selection index based on factor analysis under soil salinity screening in the greenhouse. The objective of this study was to develop a selection index model based on factor analysis and select tolerant doubled-haploid lines under high salinity conditions. The experimental design used was a split-plot design with salinity stress treatments as the main plot, i.e., normal (0 mM NaCl) and saline (25 mM NaCl ~ 5.6–5.8 dS/m) and 42 genotypes as the subplot. The genotypes consisted of 36 doubled-haploid lines, four commercial varieties, and two check varieties. The results indicated that a salinity selection index model involving yield and productive tiller traits could be used for selecting rice genotypes tolerant to salinity stress in soil artificial screening. This index which was developed through a combination of factor analysis, stress tolerance index (STI), and path analyses have identified 15 doubled haploid rice lines which were considered as good tolerant lines under salinity stress in soil artificial screening.
Callogenesis and embryogenesis are integral parts of many tissue culture procedures for genetic manipulation in rice. However, the efficiency of both processes is largely dependent on the media constituent especially the plant growth regulators (PGRs) due to the genotype-dependent nature of in vitro culture protocols. Therefore, this study investigates the effect of two PGRs; 2,4-dichlorophenoxyacetic acid (2,4-D) and kinetin (Kin) on callus growth and somatic embryogenesis of an important Malaysian rice cultivar (Oryza sativa L. cv. MARDI Siraj 297). Mature rice seeds explants were inoculated in Murashige & Skoog (MS) medium supplemented with different combinations of 2,4-D (0 to 3.5 mg/L) and Kin (0 to 0.5 mg/L) to induce callogenesis. Parameters for callus growth such as fresh weight (FW), callus induction frequency (CIF), embryogenic callus frequency (ECF), regeneration frequency (RF), number of plantlets per callus (PPC), callus texture and callus color were observed after 35 days of inoculation. The results show that the maximum callus growth was achieved in MS medium supplemented with combination of 2.0 mg/L 2,4-D and 0.2 mg/L Kin, represented by the highest FW (211 mg), CIF (95%), ECF (90%), RF (100%) and PPC (22 plantlets); along with friable callus texture. Low concentration of 2,4-D (0 to 0.5 mg/L) in the presence or absence of Kin promotes root growth instead of callus, while high concentrations (above 3.0 mg/L) retard the callus formation. The embryogenic calli from this optimized PGRs combination were successfully formed shoots in MS medium supplemented with 2 mg/L BAP and 1 mg/L NAA, followed by rooting in PGRs-free MS medium. This finding provides an efficient protocol for callogenesis and somatic embryogenesis of MARDI Siraj 297, since this is the first published report regarding somatic embryogenesis induction of this cultivar.
Research has linked increased fertilizer usage in the past twenty years to large zones of hypoxia and algal blooms in Lake Erie, the northern Gulf of Mexico and other water bodies across the U.S. Given the nature and the scale of these impacts, researchers and policymakers benefit by understanding the drivers behind the increased demand for fertilizer and fertilizer management to help develop strategies to reduce nonpoint source pollution associated with excessive fertilizer applications. The purpose of this paper is to examine the impact of crop price, specifically for corn, on expected demand for nitrogen fertilizer at the farm level. Using survey data, we examine the impact that an increase in expected corn prices could have on potential demand for nitrogen fertilizer given farm characteristics, farm demographics, and farmer behavior, holding land area and fertilizer price fixed. Results indicate that the marginal probability of a farmer increasing nitrogen fertilizer rates when crop prices increase is positive and statistically significant. In addition, we find that this marginal probability increases at a decreasing rate with moderate increases in corn price (up to around 20%) and then decreases at an increasing rate afterwards, while remaining positive. Thus, farmers are likely to increase nitrogen fertilizer applications to corn with future corn price increases.
Tempeh is a traditional fermented soybean product widely consumed as part of the staple Indonesian diet. Besides its role as a protein source, the consumption of tempeh has been associated with health benefits, such as those from antioxidants. The fermentation of soybean by tempeh starter (Rhizopus oligosporus) determines the antioxidant capacities of tempeh. Updated studies reporting the fermentation conditions effect on tempeh are limited. Therefore, this research aimed to evaluate various fermentation conditions (lactic acid addition, fermentation time, fermentation temperature) on antioxidant capacities and physical characteristics of tempeh. In this study, soybean was soaked for 4 h, dehulled and boiled in water containing lactic acid with different concentrations (0.8%, 0.9% and 1.0%) for 30 mins. After cooling, the tempeh starter (106 CFU/g of Rhizopus oligosporus) was inoculated into the soybean. Afterward, the soybean was incubated at three different temperatures (25, 30 and 35 ℃) for 2, 3 and 4 days. For each fermentation condition, the physical characteristic (L*a*b* color value), antioxidant capacities and isoflavones contents of the tempeh powder were observed. The results showed that the tempeh fermented for more than 2 days was overripe, and higher incubation temperature could intensify the speed of fermentation, resulting in darker tempeh. A significant decrease in the L* value and increases in the a* and b* values were observed on tempeh stored at longer incubation time at various storage temperatures and various lactic acid concentrations (p < 0.05). Tempeh incubated at a higher temperature and longer incubation time exhibited lower EC50 values of 2,2'-Azino-Bis-3-Ethylbenzothiazoline-6-Sulfonic Acid (ABTS) scavenging and ferrous chelating ability, increase total phenolic contents and significantly increase aglycone isoflavones (p < 0.05). Therefore, the highest antioxidant capacity, the highest total phenolic content and the highest aglycone isoflavones were found in the tempeh incubated for 4 days at 35 ℃. The 1% lactic acid-tempeh had the highest antioxidant of chelating ability, highest total phenolic content and highest aglycone isoflavone increase.
Eleutherine palmifolia is one of the medicinal plants widely used by the Dayak and Kutai tribes in Borneo Island, Indonesia as traditional medicines that can treat various diseases. Identification of the phytochemical content of E. palmifolia is very important to determine its potential as a medicinal plant. A significant factor in the success of the growth of E. palmifolia is the amount of fertilizer applied as a source of nutrients. In this study, the influence of various amounts of nitrogen (N) and potassium (K) fertilizers on the growth, total phenolic and flavonoid content (TPC and TFC), and antioxidant activity was investigated in different extracts of E. palmifolia. The treatments included 0, 46 or 92 kg/ha of N combined with 12.5 kg/ha of K, and 0, 25 or 50 kg/ha of K combined with 46 kg/ha of N. Using water, ethanol, or n-hexane as solvents, each sample was extracted with sonication method. TPC and TFC of the bulb extracts were quantified using Folin-Ciocalteu and aluminum chloride assays, respectively. Antioxidant activity was analyzed using 2,2′-diphenyl-1-picrylhydrazyl (DPPH) and ferric reducing antioxidant power (FRAP) assays. Results showed that combining N and K had no significant effects on plant height, the number of tillers, leaves, or bulbs, and bulb diameter, while the chlorophyll reading value, total plant weight, and fresh bulb weight were significantly increased. The results indicated that the availability of N and K has a substantial effect on TPC, TFC, and antioxidant activity. The aqueous extract had the highest TPC and DPPH scavenging activity, whereas the ethanol extract exhibited the highest TFC and antioxidant FRAP activity. Therefore, to improve fresh bulb weight, phenol and flavonoid content, and antioxidant properties of E. palmifoliaaqueous and ethanol extracts, supplementation of 46 kg/ha N and 12.5 kg/ha K is recommended.
The objectives of this study were to assess the microbial quality of honey, evaluate the effect of microwaves on microbial survival, and assess the antibacterial activity of honey. Bacteria, yeast and mold were evaluated in samples before and after microwave treatment. Dominant bacterial contaminants were also identified. The antibacterial activity of honey was assessed against nine pathogens using an agar well diffusion assay. The minimum inhibitory concentration was determined for four honey samples that exhibited the highest antibacterial activity. In addition, one sample of Manuka honey was tested to compare its microbial load as well as its antibacterial activity to local honey samples. Sequencing using 16S rRNA gene was used for the identification of dominant bacteria. The average standard plate count, yeasts and molds were 286.5, 161.0 and 25.5 CFU/g, respectively. Microwave treatment decreased microbial populations gradually with increasing power levels and exposure times. The present study indicated that raw honey had a significant antibacterial activity which decreased following microwave treatment. The identity of 125 isolates was confirmed with Bacillus being most frequently isolated.
Groundnut is an important crop grown by smallholder farmers in West Africa for both domestic and market consumption. In groundnut cultivation, earthing up, or covering the plant's base and lower nodes with soil, is a common practice. However, there is no consistent evidence about its economic benefit. From 2016 to 2018, a three-year experiment was conducted to assess the benefits of earthing up and establish the best time to do so to increase groundnut yield, thus filling a knowledge gap in the region. The experiment was set up in a split-plot design, with the planting arrangement as the main plot (ridge vs flatbed planting) and the timing of earthing up as the subplot. The earthing up timing was divided into ten treatments, ranging from no earthing up (control) to earthing up at 70 days after planting. Data was collected on the number of matured pods per plant, dry pod yield, dry haulm yield, shelling percentage, and 100 seeds weight. The results for the time of earthing up revealed that there was no statistically significant difference in dry pod yield and dry haulm yield except in 2017. Similarly, for the number of matured pods per plant, 100 seeds weight, and shelling percentage, there was no statistically significant difference between times of earthing up except for 100 seeds weight in 2018 and shelling percentage in 2017 and 2018. The individual years and combined analyses across years revealed no statistically significant difference between the main plots for all the five traits. The combined analysis for the times of earthing up showed a significant difference only for shelling percentage. Therefore, in the Sudan Savanah agro-climatic conditions of the semi-arid tropics of West Africa, earthing up may not be economically beneficial during a typical rainfall season with appropriate planting time. Instead, it could raise production costs, reducing the profit.
The effect of High Hydrostatic Pressure (HHP) on Escherichia coli and Listeria innocua in carrot juice was evaluated just after pressurization and during refrigerated storage for 14 days. Samples were processed with different variants of pressure (300, 400, 500) and time (1 min, 5 min, and 10 min). The number of bacteria in the populations was analyzed using plating count methods. Required 5 log reduction was achieved only for L. innocua strains starting from 400 MPa for 5 min. E. coli strains displayed resistance to pressure, and the maximum reduction achieved was 2 log CFU/mL for the harshest process parameters. Sublethal injuries in the bacterial population were observed for all tested strains. According to two standardized ISO methods, selective conventional agars, TBX, and ALOA were used in the storage test. Additionally, the Thin Agar Layer (TAL) method was applied. In both used methods, the possibilities of recovery were provided. The regeneration was observed exclusively for L. innocua strains. The recovery of sublethally injured cells on ALOA and TAL did not differ statistically in every strain. In turn, results obtained for E. coli suggest that TBX may underestimate the number of HHP-injured bacteria.
This work focuses on the area of food waste from the subjective perspective of the consumers themselves. The key source of data is a questionnaire survey with a sample selection of 3,429 respondents from the Czech Republic, Poland, and Slovakia, which are countries with historical and cultural ties. This survey was orchestrated in 2019 and it aimed to uncover the consumers’ stances on this area. For every country involved, the results proved that the most common reason for food waste is that the food spoils when stored. One’s stance on food waste is influenced by identifiers such as age, education, economic activity, and perceived income. A significant difference between the surveyed countries can be seen in the fact that Poles have over a 10× greater chance of wasting the smallest amount of food. Descriptive statistics, contingency analysis, and logistic regression were used to analyze the data. It is evident that subsequent research is necessary in this area, ideally with a united methodology for every country in the European Union.
Vertical integration is a means of increasing market power. For some agricultural products, it is easier for farmers to exert control over their product beyond the farm gate, but for others it is more difficult. Cases in the latter category have two main characteristics. First, the farmer cannot sell the respective product to final consumers without processing. Second, processing is capital-intensive. Consequently, farmers have limited sales channels, and vertical integration of the supply chain is complex and challenging. It implies cooperation among farmers to process the raw material at a profitable scale and to finance the installation of processing facilities. Thus, for these product categories, farmers are prone to market power issues, since they depend on private businesses that have the financial means to install processing facilities and the logistical capacities to organize the collection of large amounts of raw material. This paper aims to identify and analyze the role of supply chain integration for farmers who are already cooperating horizontally. Two case studies serve as the basis for the analysis: sugar beet in Flanders, Belgium, and oilseed rape in Hessen, Germany. The analysis is based on a qualitative research approach combining interviews, focus groups, and workshops with farmers and processors. While for sugar beet, the effects of market power are emerging only now with the termination of the quota system, farmers growing oilseed rape have been experiencing these problems since the 1990s. Our analysis concludes that most strategies to maintain or improve farm income have been exhausted. Even various forms of vertical integration supported by European policies do not necessarily work as a successful strategy.
Viscosity of glucomannan (GM) needs to be modified to support its application for spray drying encapsulation. The purpose of this study was to investigate degradation of GM using cellulase that fulfills viscosity in a spray-dryer specification. This hydrolyzed glucomannan (HGM) was subsequently spray-dried for encapsulating iron. Lower initial GM concentrations (0.5–1%) reached approximately 0.30 Pa·s which allowed to be spray-dried after 100 min degradation using 10 mg/L cellulase. Meanwhile, viscosity of 1.5% and 1.7% GM did not reach the target viscosity even after 300 min. The nth-order model was the most suitable model which fitted viscosity reduction of ≤1.5% initial GM concentration (coefficient of determination, R2 > 0.98), whereas the Mahammad model fitted the viscosity reduction of 1.75% initial GM concentration (R2 = 0.99). Hydrolysis decreased the degree of polymerization and surface tension but increased the antioxidant activities of HGM. Smaller molecules of the polysaccharides were released after hydrolysis. Particles of encapsulated iron using HGM were more hydrophilic than those using GM. The iron tended to have a higher release rate at pH 6.8 than at pH 1.2 in the first 40 min. Hence, the HGM showed its ability to act as a control release matrix for the iron that needs a protection in the acid environment, and delivers them to the neutral site for absorption. Nanoencapsulation using 0.35 Pa·s viscosity of HGM was able to have 84% yield, 96.41% encapsulation efficiency, and 10% moisture content. Particle size of the iron encapsulation was dominated by 341.99 nm-diameter. This study shows a potency to use an appropriate viscosity of HGM which not only allows to be spray-dried but also support in protecting the iron as aimed by encapsulation the iron. Performances and properties of this matrix on encapsulating other bioactive compounds become future study.
This research was undertaken in the agropastoral regions of Maradi, Tahoua and Tillabéri in Niger. The first study covered 900 households and assessed farmers production methods, income, household expenditure, gender issues and food security using four different indicators. The second study assessed causes for child malnutrition by combining a household survey (450 households) with measurement of the upper arm circumference of 1618 children aged 6 to 59 months from these households. A logistic regression analysis was used to identify the causes for malnutrition. The number of food-insecure months in the households were on average 3.54 months per year and 11.4% of the children belonged to the group defined as suffering from ‘global acute malnutrition’. Cereal yields were below 250 kg ha-1 and only 33% of the households were able to sell any of their cereal harvest. The households spent 66% of their total expenditure on the purchase of food. Money spent on diversifying their nutrition was very limited and horticulture production focused on temperate crops. The indicators for nutrition diversity, food quality and household perception of food security were low. The major causes identified for food insecurity and child malnutrition were low agricultural production, low nutritional diversity, women’s autonomy in agriculture (control over income) and poor sanitation. To address these challenges, we propose a mix of incremental and transformative changes, including strengthening the role of women, promotion of precision farming, nutrient-sensitive agriculture, eco-sanitation, and training on improved nutrition and childcare.
Lower bed single-row pineapple cultivation could protect pineapple from soil erosion during the rainy season and drought period; however, disease problems could arise as a result of water logging. Two experiments were conducted in Ultisol soil using a lower bed single row to investigate the ability of gypsum to provide soil calcium (Ca) to the pineapple plant, plant resistance to heart rot disease, and provide a better effect on crop growth and fruit quality. In the first trial, four levels of gypsum (0, 1.0, 1.5 and 2.0 Mg·ha−1) and dolomite (2 Mg·ha−1) were spread and incorporated into soil that had been saturated with Phytophthora nicotianae inoculums. In the second trial, gypsum treatments (0, 1.0, 1.5, 2.0 and 2.5 Mg·ha−1) were used as a basic fertiliser in the row between the single beds. P. nicotianae attacked all treatments at 6 weeks after planting (WAP), and at 10 WAP, the mortality of the dolomite treatment reached 63.8%, significantly higher than that of the gypsum treatments (3.3%–14.3%). In the second experiment, gypsum significantly increased plant weight from 3 to 9 months after planting (MAP), especially when applied at 1.5–2.5 Mg·ha−1. Fruit texture, total soluble solids (TSS), and titratable acidity (TA) were not significantly different between treatments, but they all met the standards for canned pineapple grades. The results showed that soil-applied gypsum before planting provides soil calcium, meets the plant Ca requirement during an early and fast growth stage, and is free of heart rot disease.
Low energy electron beam (e-beam) has the ability to decontaminate or reduce bioburden and enhance the food product’s safety with minimal quality loss. The current study aimed to evaluate the efficacy of e-beam on natural microbiota and quality changes in black peppercorns. The black pepper was exposed to e-beam at doses from 6–18 kGy. The microbial quality, physicochemical attributes, total phenolic compounds, and antioxidant activity were evaluated. Results demonstrated the microbial population in black pepper decreased with increasing e-beam treatment doses. Significant inactivation of Total Plate Count (TPC), yeasts, and molds were observed at dose 6 kGy by 2.3, 0.7, and 1.3 log CFU g−1, respectively, while at 18 kGy the reduction level was 6, 2.9, and 4.4 log CFU g−1, respectively. Similarly, 18 kGy of e-beam yielded a reduction of 3.3 and 3.1 log CFU g−1 of SalmonellaTyphimurium and coliform bacteria, respectively. A significant difference (p <0.05) was noted between doses 12, 15, and 18 kGy on Bacillus cereusand Clostridium perfringensin black pepper. During e-beam doses, the values L⁎ , a⁎ and b⁎ of black peppercorn were not noticeably altered up to 18 kGy dose. No significant (p > 0.05) difference in moisture, volatile oil, and piperine content upon (6–18 kGy) treatments in comparison to the control. A slight difference in the bioactive compound, retaining >90% of total phenolic compounds and antioxidant activity. Results revealed that e-beam doses ≥ 18 kGy were influential for inactivating natural microbes and foodborne pathogens without compromising the physicochemical properties and antioxidant activity of black peppercorns.