Kinematic design of an anthropomimetic 7-DOF cable-driven robotic arm

Abstract

In this paper, an anthropomimetic design of a 7-DOF dexterous robotic arm is proposed. Similar to the human arm, the arm consists of three sequentially connected modules, i.e., a 3-DOF shoulder module, a 1-DOF elbow module, and a 3-DOF wrist module. All three arm modules are also driven by cables in order to mimic the driving scheme and functionality of the human muscles. This paper addresses three critical design analysis issues, i.e., the displacement analysis, the tension-closure analysis, and the workspace analysis. A closed-form solution approach is presented for the forward displacement analysis, while the inverse displacement solution is obtained through an efficient optimization algorithm, in which both task-decomposition and dimension-reduction techniques are employed. An effective tension-closure analysis algorithm is also formulated based on the theory of convex analysis. The orientation workspace for the 3-DOF shoulder and wrist modules are then analyzed using a new equi-volumetric partition scheme based on the intuitive Tilt-and-Torsion angle parameterization. An optimization approach is then investigated for the kinematic design of the three joint modules, in which the design objective is to maximize the matched workspace of the robotic arm joints with that of the human arm joints. A research prototype of the 7-DOF cable-driven robotic arm has also been developed in order to demonstrate the anthropomimetic design concept. With a lightweight structure of 1 kg, the cable-driven robotic arm can carry a payload of 5 kg and has motion repeatability of±2.5mm.

Key words： anthropomimetic design; robotic arm; cable-driven mechanism; kinematic analysis; design optimization

Acknowledgment

The authors would like to acknowledge that this work was partly supported by the Singapore Institute of Manufacturing Technology, A*STAR and the Nanyang Technological University (under Academic Research Fund RG 24/06).

References

1 Kwee H, Quaedackers J, Van de Bool E, Theeuwen L, Speth L. Ocus project: Adapting the control of the manus manipulator for persons with cerebral palsy. In: Proceedings of IEEE ICORR. Stanford, CA, 1999, 106-114

2 Romer G R B E, Stuyt H J A, Peters A. Cost-savings and economic benefits due to the assistive robotic manipulator (ARM). In: Proceedings of IEEE ICORR. Chicago, IL, 2005, 201-204

3 Alqasemi R M, McCaffrey E J, Edwards K D, Dubey R V. Analysis, evaluation and development of wheelchair-mounted robotic arms. In: Proceedings of IEEE ICORR. Chicago, IL, 2005, 469-472

4 Topping M, Smith J. The development of handy 1: A robotic system to assist the severely disabled. In: Proceedings of ICORR. Stanford, CA, 1999, 244-249

5 Krebs H I, Palazzolo J J, Dipietro L, Ferraro M, Krol J, Rannekleiv K, Volpe B T, Hogan N. Rehabilitation robotics: Performance-based progressive robot-assisted therapy. Autonomous Robots, 2003, 15(1): 7-20

6 Lusardi M M, Nielsen C C. Orthotics and Prosthetics in Rehabilitation: Butterworth Heinemann, 2000

7 Tsagarakis N G, Caldwell D G. Development and control of a ‘soft-actuated’ exoskeleton for use in physiotherapy and training. Autonomous Robots, 2003, 15(1): 21-33

8 Kiguchi K, Tanaka T, Watanabe K, Fukuda T. Design and control of an exoskeleton system for human upper-limb motion assist. In: Proceedings of IEEE/ASME AIM. Kobe, 2003, 926-931

9 Homma K, Fukuda O, Sugawara J, Nagata Y, Usuba M. A wire-driven leg rehabilitation system: Development of a 4-dof experimental system. In: Proceedings of IEEE/ASME AIM. Kobe, 2003, 908-913

10 Surdilovic D, Bernhardt R. String-man: A new wire robot for gait rehabilitation. In: Proceedings of IEEE ICRA. New Orleans, LA, 2004, 2031-2036

11 Bernhardt M, Frey M, Colombo G, Riener R. Hybrid force-position control yields cooperative behaviour of the rehabilitation robot LOKOMAT. In: Proceedings of IEEE ICRA. Chicago, IL, 2005, 536-539

12 Takahashi Y, Suzuki T, Obuchi Y, Kusakabe K, Takahashi K, Sakamoto T. Evaluations of human physical burdens when using transfer aid robotic system. In: Proceedings of SICE. Hokkaido, 2004, 933-938

13 Cook A M, Bentz B, Harbottle N, Lynch C, Miller B. School-based use of a robotic arm system by children with disabilities. IEEE Transactions on Neural Systems and Rehabilitation Engineering, 2005, 13(4): 452-460

PMID

14 Robins B, Dickerson P, Dautenhahn K. Robots as embodied beings- interactionally sensitive body movements in interactions among autistic children and a robot. In: Proceedings of IEEE RO-MAN. Nashville, TN, 2005, 54-59

15 Graf B, Hans M, Kubacki J, Schraft R D. Robotic home assistant care-o-bot II. In: Proceedings of the Second Joint Meeting of the IEEE Engineering in Medicine and Biology Society and the Biomedical Engineering Society. Houston, Texas, 2002, 2343-2344

16 Pineau J, Montemerlo M, Pollack M, Roy N, Thrun S. Towards robotic assistants in nursing homes: Challenges and results. Robotics and Autonomous Systems, 2003, 42(3-4): 271-281

17 Balaguer C, Gimenez A, Huete A J, Sabatini A M, Topping M, Bolmsjo G. The mats robot: Service climbing robot for personal assistance. IEEE Robotics & Automation Magazine, 2006, 13(1): 51-58

18 Asfour T, Berns K, Dillmann R. The humanoid robot ARMAR. In: Proceedings of the 2nd International Symposium in Humanoid Robots. Tokyo, 1999, 174-180

19 Asfour T, Dillmann R. Human-like motion of a humanoid robot arm based on a closed-form solution of the inverse kinematics problem. In: Proceedings of IEEE/RSJ IROS. Las Vegas, Nevada, 2003, 1407-1412

20 Zinn M, Khatib O, Roth B. A new actuation approach for human friendly robot design. In: Proceedings of IEEE ICRA. New Orleans, LA, 2004, 249-254

21 Yoon S S, Kang S, Kim S J, Kim Y H, Kim M, Lee C W. Safe arm design with mr-based passive compliant joints and visco-elastic covering for service robot applications. In: Proceedings of IEEE/RSJ IROS. Las Vegas, Nevada, 2003, 2191-2196

22 Jeong S H, Takahashi T, Nakano E. A safety service manipulator system: The reduction of harmful forces by a controllable torque limiter. In: Proceedings of IEEE/RSJ ROS. Sendai, Japan, 2004, 162-167

23 Tondu B, Ippolito S, Guiochet J, Daidie A. A seven-degrees-of-freedom robot-arm driven by pneumatic artificial muscles for humanoid robots. International Journal of Robotics Research, 2005, 24(4): 257-274

24 Yokoi K, Tanie K, Inamura N, Kawai T, Agou K. Design and control of a seven-degrees-of-freedom manipulator actuated by a coupled tendon-driven system. In: Proceedings on IEEE/RSJ IROS. Osaka, Japan, 1991, 737-742

25 Salisbury K, Eberman B, Levin M, Townsend W. An experimental whole-arm manipulator. Artificial intelligence at MIT: Expanding Frontiers. Cambridge, MA: MIT Press, 1990, 228-249

26 Lenarcic J, Stanisic M. A humanoid shoulder complex and the humeral pointing kinematics. IEEE Transactions on Robotics and Automation, 2003, 19(3): 499-506

27 Murray R, Li Z, Sastry S S. A Mathematical Introduction to Robotic Manipulation. CRC Press, 1994

28 Brockett R. Robotic manipulators and the product-of-exponential formula. Mathematical Theory of Network and Systems. New York: Springer, 1984, 120-129

29 Rockafella R T. Convex Analysis. Princeton University Press, 1970

30 Lim W B, Yang G, Yeo S H, Mustafa S K, Chen I M. A Generic Tension-Closure Analysis Method for Fully-Constrained Cable-Driven Parallel Manipulators. In: Proceedings of IEEE ICRA. Kobe, 2009, 2187-2192

31 Hamilton N, Luttgens K. Kinesiology: Scientific Basis of Human Motion. Mc-Graw Hill, 2002

32 Korein J U. A Geometric Investigation of Reach.Cambridge, MA: MIT Press, 1984

33 Bonev I A, Gosselin C M. Analytical determination of the workspace of symmetrical spherical parallel mechanisms. IEEE Transactions on Robotics, 2006, 22(5): 1011-1017

34 Bonev I A, Gosselin C M. Singularity Loci of Spherical Parallel Mechanisms. In: Proceedings of IEEE ICRA. Barcelona, 2005, 2968-2973

35 Yang G, Lin W, Mustafa S K, Chen I M, Yeo S H. Numerical orientation workspace analysis with different parameterization methods. In: Proceedings of IEEE CISRAM. Bangkok, Thailand, 2006, 720-725

36 Chirikjian G S, Kyatkin A B. Engineering Applications of Noncommutative Harmonic Analysis with Emphasis on Rotation and Motion Groups.Boca Raton: CRC Press, 2000

37 Deb K. Optimization for Engineering Design: Algorithms and Examples.New Delhi: Prentice-Hall, 1998