非对称板式换热器传热和流动阻力特性模拟和实验研究

Numerical simulation and experimental research on heat transfer and flow resistance characteristics of asymmetric plate heat exchangers

Abstract

The asymmetric plate heat exchanger (APHE) has the possibility of achieving balanced pressure drops on both hot and cold sides for situations with unbalanced flow, which may in turn enhance the heat transfer. In this paper, the single-phase water flow and heat transfer of an APHE consisted of two types of plates are numerically (400≤Re≤12000) and experimentally (400≤Re≤ 3400) investigated. The numerical model is verified by the experimental results. Simulations are conducted to study the effects of N, an asymmetric index proposed to describe the geometry of APHEs. The correlations of the Nusselt number and friction factor in the APHEs are determined by taking N and working fluids into account. It is found that an optimal N exists where the pressure drops are balanced and the heat transfer area reaches the minimum. The comparison between heat transfer and flow characteristics of the APHEs and the conventional plate heat exchanger (CPHE) is made under various flow rate ratios of the hot side and the cold side and different allowable pressure drops. The situations under which APHE may perform better are identified based on a comprehensive index Nu/f^1/3.

Keywords

plate heat exchanger / asymmetric / simulation / correlation / heat transfer enhancement

参考文献

[1] Odejobi O J, Adejokun A E, Al-Mutairi E M. Heat exchanger network synthesis incorporating enhanced heat transfer techniques. Applied Thermal Engineering, 2015, 89: 684–692

[2] Caputo A C, Pelagagge P M, Salini P. Heat exchanger optimized design compared with installed industrial solutions. Applied Thermal Engineering, 2015, 87: 371–380

[3] Doo J H, Ha M Y, Min J K, Stieger R, Rolt A, Son C. An investigation of cross-corrugated heat exchanger primary surfaces for advanced intercooled-cycle aero engines (Part-I: Novel geometry of primary surface). International Journal of Heat and Mass Transfer, 2012, 55(19–20): 5256–5267

[4] Bejan A, Alalaimi M, Sabau A S, Lorente S. Entrance-length dendritic plate heat exchangers. International Journal of Heat and Mass Transfer, 2017, 114: 1350–1356

[5] Abu-Khader M M. Plate heat exchangers: recent advances. Renewable & Sustainable Energy Reviews, 2012, 16(4): 1883–1891

[6] Abou Elmaaty T M, Kabeel A E, Mahgoub M. Corrugated plate heat exchanger review. Renewable & Sustainable Energy Reviews, 2017, 70: 852–860

[7] Nilpueng K, Keawkamrop T, Ahn H S, Wongwises S. Effect of chevron angle and surface roughness on thermal performance of single-phase water flow inside a plate heat exchanger. International Communications in Heat and Mass Transfer, 2018, 91: 201–209

[8] Kanaris A G, Mouza A A, Paras S V. Optimal design of a plate heat exchanger with undulated surfaces. International Journal of Thermal Sciences, 2009, 48(6): 1184–1195

[9] Zhang L, Che D. Influence of corrugation profile on the thermalhydraulic performance of cross-corrugated plates. Numerical Heat Transfer, 2011, 59(4): 267–296

[10] Doo J H, Ha M Y, Min J K, Stiegerc R, Roltc A, Sona C. An investigation of cross-corrugated heat exchanger primary surfaces for advanced intercooled-cycle aero engines (Part-II: Design optimization of primary surface). International Journal of Heat Mass Transfer, 2013, 61(s19–20): 138–148

[11] Utriainen E, Sunden B. Evaluation of the cross corrugated and some other candidate heat transfer surfaces for microturbine recuperators. Journal of Engineering for Gas Turbines and Power, 2002, 124(3): 550–560

[12] Focke W W. Asymmetrically corrugated plate heat-exchanger plates. International Communications in Heat and Mass Transfer, 1985, 12(1): 67–77

[13] Kim M, Ha M Y, Min J K, Stieger R, Rolt A, Son C. Numerical study on the cross-corrugated primary surface heat exchanger having asymmetric cross-sectional profiles for advanced intercooled-cycle aero engines. International Journal of Heat and Mass Transfer, 2013, 66: 139–153

[14] Vestergren U. Plate heat exchanger. United State Patent 6237679B1, 2001

[15] Dahlberg T. Asymmetric heat exchanger. European Patent 2267391A2, 2010

[16] Funke M. Asymmetric plate heat exchanger. European Patent 2674718, 2013

[17] Lee H, Hwang Y, Radermacher R, Chun H H. Experimental investigation of novel heat exchanger for low temperature lift heat pump. Energy, 2013, 51: 468–474

[18] Jain S, Joshi A, Bansal P K. A new approach to numerical simulation of small sized plate heat exchangers with chevron plates. Journal of Heat Transfer, 2007, 129(3): 291–297

[19] Sharif A, Ameel B, T’Jollyn I, Lecompte S, De Paepe M. Comparative performance assessment of plate heat exchangers with triangular corrugation. Applied Thermal Engineering, 2018, 141: 186–199

[20] Zhang Y, Jiang C, Yang Z, Zhang Y, Bai B. Numerical study on heat transfer enhancement in capsule-type plate heat exchangers. Applied Thermal Engineering, 2016, 108: 1237–1242

[21] Han X H, Cui L Q, Chen S J, Chen G M, Wang Q. A numerical and experimental study of chevron, corrugated-plate heat exchangers. International Communications in Heat and Mass Transfer, 2010, 37(8): 1008–1014

[22] Gullapalli V S, Sunden B. CFD simulation of heat transfer and pressure drop in compact brazed plate heat exchangers. Heat Transfer Engineering, 2014, 35(4): 358–366

[23] Tiwari A K, Ghosh P, Sarkar J, Dahiya H, Parekh J. Numerical investigation of heat transfer and fluid flow in plate heat exchanger using nanofluids. International Journal of Thermal Sciences, 2014, 85: 93–103

[24] Wu Q G. The optimality of orthogonal experimental designs. Acta Mathematicae Applicatae Sinica, 1978, 4: 283–299

[25] Wheeler A J, Ganji A R. Introduction to Engineering Experimentation. New Jersey: Pearson Prentice Hall, 2004

[26] Lee J, Lee K S. Friction and colburn factor correlations and shape optimization of chevron-type plate heat exchangers. Applied Thermal Engineering, 2015, 89: 62–69

[27] Sarraf K, Launay S, Tadrist L. Complex 3D-flow analysis and corrugation angle effect in plate heat exchangers. International Journal of Thermal Sciences, 2015, 94: 126–138

[28] Martin H. A theoretical approach to predict the performance of chevron-type plate heat exchangers. Chemical Engineering and Processing, 1996, 35(4): 301–310

[29] Fernández-Seara J, Uhía F J, Sieres J, Campo A. A general review of the Wilson plot method and its modifications to determine convection coefficients in heat exchange devices. Applied Thermal Engineering, 2007, 27(17–18): 2745–2757

Acknowledgments

This work was supported by the National Key Research and Development Program of China (No. 2016YFB0901404).

版权

2020 Higher Education Press