Application of high-turning bowed compressor stator to redesign of highly loaded fan stage

Application of high-turning bowed compressor stator to redesign of highly loaded fan stage

Abstract

A redesign of a highly loaded fan stage by using high-turning bowed compressor stator was conducted. The original tandem stator was replaced by the highly loaded bowed stator which was applicable to highly subsonic flow conditions. 3D contouring technique and local modification of blade were applied to the design of the bowed blade in order to improve the aerodynamic performance and the matching of the rotor and stator blade rows. Performance curves at different rotating speeds and performances at different operating points for both the original fan stage and redesigned fan stage were obtained by numerical simulations. The results show that the highly loaded bowed stator can be used not only to improve the structure and the aerodynamic performances at various operating points of the compressor stage but also to provide high performances at off-design conditions. It is believed that the highly loaded bowed stator can advance the design of high-performance compressor.

参考文献

1. Chen Maozhang . Development of fan/compressor techniques and suggestions on furtherresearches. Journal of Aerospace Power, 2002, 17(1): 1–15
2. Bryce J D, Cherrett M A, Lyes P A . Three-dimensional flow in a highly loaded single-stagetransonic fan. ASME Journal of Turbomachinery, 1995, 117(1): 22–28
3. Emmerson P R . Three-dimensional flow calculations of the stator in a highly loadedtransonic fan. American Society of MechanicalEngineers Report ASME 1996-GT-546. 1996
4. Calvert W J, Emmerson P R, Moore J M . Design, test and analysis of a high-pressure-ratio transonicfan. American Society of Mechanical EngineersReport ASME 2003-GT-38302. 2003
5. Friedrichs J, Sven Baumgarten, Gunter Kosyna, et al.. Effect of stator design on stator boundary layerflow in a highly loaded single-stage axial-flow low-speed compressor. American Society of Mechanical Engineers ReportASME 2000-GT-616. 2000
6. Boese M, Fottner L . Effects of riblets on theloss behavior of a highly loaded compressor cascade. American Society of Mechanical Engineers Report ASME 2002-GT-30438. 2002
7. Douglas J W, Li S M, Song B, et al.. Effects of free stream turbulence on the lossesof a highly loaded compressor stator blade. American Society of Mechanical Engineers Report ASME 2003-GT-38604. 2003
8. Hilgenfeld L, Pfitzner M . Unsteady boundary layer developmentdue to wake passing effects on a highly loaded linear compressor cascade. American Society of Mechanical Engineers ReportASME 2004-GT-53186. 2004
9. Liu Baojie, Zou Zhengping, Yan Ming, et al.. Present status and future development of CFDin Turbomachinery. Acta Aeronautica EtAstronautica Sinica, 2002, 23(5): 394–404
10. Wellborn S R, Delaney R A . Redesign of a 12-stage axial-flowcompressor using multistage CFD. AmericanSociety of Mechanical Engineers Report ASME 2001-GT-0351. 2001
11. Gallimore S J, Bolger J J, Cumpsty N A, et al.. The use of sweep and dihedral in multistageaxial flow compressor blading, part 1: University research and methodsdevelopment. American Society of MechanicalEngineers Report ASME 2002-GT-30328. 2002
12. Gallimore S J, Bolger J J, Cumpsty N A, et al.. The use of sweep and dihedral in multistageaxial flow compressor blading, part 2: Low and high speed designsand test verification. American Societyof Mechanical Engineers Report ASME 2002-GT-30329. 2002
13. Breugelmans F A E, Carels Y, Demuth M . Influence of dihedral on the secondary flow in a two-dimensionalcompressor cascade. ASME Journal of Engineeringfor Gas Turbine and Power, 1984, 106(3): 578–584
14. Brilliant L, Balamucki S, Burger G, et al.. Application of multistage CFD analysis to lowpressure compressor design. American Societyof Mechanical Engineers Report ASME 2004-GT-54263. 2004
15. Li Shaobin, Su Jiexian, Feng Guotai, et al.. Effect of blade bowing and local modificationon high-turning angle compressor stator performance. The 11th Engineering Thermophysics Conference of China, Dalian, 2005, Paper serial number: 052043